Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.
Now unloading and repeated module loading is working just fine.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading for Netgear R7500
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Use the stateless 4-byte op codes for this flash chip to fix reboot
hangs on SoCs expecting the flash chip in 3-byte mode.
Fixes: FS#179
Signed-off-by: Mathias Kresin <dev@kresin.me>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116
Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with (phy, offset, value, mask)
The patch is swapping value and mask.
Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:
root@LEDE:/# rmmod dwc3
[ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.168084] usb usb4: USB disconnect, device number 1
[ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.182960] usb usb3: USB disconnect, device number 1
[ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
[ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.205912] usb usb2: USB disconnect, device number 1
[ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.221751] usb usb1: USB disconnect, device number 1
[ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[ 29.583343] phy phy-100f8830.phy.4: phy init failed --> -110
[ 29.583399] dwc3 10000000.dwc3: failed to initialize core
[ 29.588169] dwc3: probe of 10000000.dwc3 failed with error -110
[ 29.652943] phy phy-110f8830.phy.2: phy init failed --> -110
[ 29.652988] dwc3 11000000.dwc3: failed to initialize core
[ 29.657735] dwc3: probe of 11000000.dwc3 failed with error -110
root@LEDE:/#
With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.622298] usb usb4: USB disconnect, device number 1
[ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.637054] usb usb3: USB disconnect, device number 1
[ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.652910] usb usb2: USB disconnect, device number 1
[ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.668604] usb usb1: USB disconnect, device number 1
[ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[ 25.426509] hub 1-0:1.0: USB hub found
[ 25.431626] hub 1-0:1.0: 1 port detected
[ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.452926] hub 2-0:1.0: USB hub found
[ 25.460420] hub 2-0:1.0: 1 port detected
[ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[ 25.546583] hub 3-0:1.0: USB hub found
[ 25.551997] hub 3-0:1.0: 1 port detected
[ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.573063] hub 4-0:1.0: USB hub found
[ 25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#
Fixes: dwc3 module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.
Fixes FS#497
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.
Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9
* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.
By design unlike other qcom boards ipq do not use clocks to connect to scm.
Considering this we're removing from DT and scm driver clocks for ipq boards.
As a result cpuidle does not produce errors about failed configuration anymore.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The available amount of coherent DMA memory is very limited. On Linux
4.4 this issue was worked around by increasing the pool size.
It turns out that using coherent memory here is completely unnecessary.
This change reworks the driver code to use kzalloc+dma_map_single
instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.
Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.
Runtime-tested on ar71xx, octeon, ramips and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.
The second change removes settings now present in base dts.
The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.
Signed-off-by: André Valentin <avalentin@marcant.net>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.
This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.
It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Thomas Reifferscheid
Mathias Kresin
Hauke Mehrtens
Pavel Kubelun
John Crispin
Christian Lamparter
Hannu Nyman
Felix Fietkau
Jo-Philipp Wich
Stijn Tintel
Joseph C. Lehner
André Valentin
Zhang Jingye