oneshot trigger configurations for LEDs are created, but the on/off
timing configurations are ignored. generate_config is correctly creating
oneshot configs, but the later led script doesn't recognise the trigger
details.
Fixes: c0c3f2d4c9 leds: support oneshot as well as timer triggers
Signed-off-by: Karl Palsson <karlp@etactica.com>
Due to an empty pi_ifname in the generic failsafe setup, the deconfig
never removed the failsafe networking interface, causing broken
networking later on.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Also configure the switch based on the failsafe config, and create the
failsafe interface as tagged if necessary.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
In preparation of properly setting up vlans and switches, add
support for configuring failsafe on a vlan tagged interface.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Move preinit interface and ip config to its own function to allow
calling it from more than one place.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of board_detect generating the config as a side effect, let
config_generate call board_detect as needed.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The pi_* variables and the fs_failsafe_wait_timeout variable are set by
the CONFIG_TARGET_PREINIT_* config options. No need to maintain the same
values twice.
All other fs_ variables were never used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
sysupgrade immediately reboots after flashing an image and doesn't
allow to unmount filesystems. At least in case the image used for
sysupgrade is stored on a FAT formatted usb flash drive, the following
warning is printed during the next mount of the flash drive:
FAT-fs (sda1): Volume was not properly unmounted. Some data may be
corrupt. Please run fsck.
Although a data corruption during read operations is unlikely, there is
no need to scare the users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
/etc/init.d/boot tried to create /dev/root based on the kernel's
cmdline which won't work on any recent targets. Remove that code now
that fstools can detect the mounted rootfs based on
/proc/self/mountinfo and /dev/root was long gone anyway.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Network drivers typically allocate memory in atomic context. For that to
be reliable, there needs to be enough free memory. Set the value
heuristically based on the total amount of system RAM.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Treat 'relayd' as an essential service to avoid connection interruptions during sysupgrade on devices configured as a pseudobridge.
Signed-off-by: Conn O'Griofa <connogriofa@gmail.com>
Previous implementation was blocking the init and
breaking halt/reboot/sysupgrade (reported by Daniel Golle)
v2: use procd logging, use set -e + trap for error handling
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
This commit:
1) seed /dev/urandom with the saved seeds as early as possible
(see /lib/preinit/81_urandom_seed)
2) save a seed at /etc/urandom.seed if it doesn't exists
3) save a new seed each boot at "system.@system[0].urandom_seed"
(see /etc/init.d/urandom_seed)
We use getrandom() so we are sure /dev/urandom pool is initialized
Seed size is 512 bytes (ie /proc/sys/kernel/random/poolsize / 8)
it's the same size as in ubuntu 14.04 and all systemd systems
Seeding /dev/urandom doesn't change entropy estimation, so we still have
"random: ubus urandom read with 4 bits of entropy available"
messages in the logs, but we can now ignore them if
after "urandom-seed: Seeding with ..." message
Saving a new seed on each boot is disabled by default to avoid too much
writes without user consent
v2: log preinit messages to /dev/kmsg
v3: use non generic function name for logging, as /lib/preinit/ files
are all sourced together in /etc/preinit
v4: after a lot of discussion on the ML, use a uci config param
v5: config param is now the path of the seed
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
dnsmasq's dnssec time checking method now uses a ntp hotplug mechanism,
therefore dnsmasq.time is redudant and no longer needs to be explicitly
excluded from sysfixtime.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
/etc/os-release is the standard distribution release information
file, therefore add it (and image configuration options for
fields not previously present in LEDE). Once it is deemed
reasonable the non-standard openwrt_release, openwrt_version,
and device_info files could be removed (that is with this patch
we consider them deprecated in favour of the standard file).
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Increase the default system log buffer size
from 16 kB (built-in default in ubox logd)
to 64 kB by setting the option in /etc/config/system.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Record the state of any hardware LED configured through UCI and use that
information to revert the state when applying updated settings while
maintaining default behaviour of system LEDs.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The board_detect framework is now able to create the entire system config from
scratch so we can finally drop the copy shipped by base-files.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that config_generate is able to generate the entire /etc/config/system
from scratch we can apply the same logic as used for /etc/config/network;
when the configuration file exists already then do not do anything, else
generate it from the values provided by /etc/board.json .
In order to facilitate that move the file existance checking inside
/bin/config_generate and call it unconditionally from /bin/board_detect.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Attempt to reset all LED states before applying the UCI configuration to
avoid leaving disabled LEDs behind in lingering glowing state, e.g. when
changing the sysfs entry in the config from one hardware LED to another.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some package postinstall operations, e.g. those emitted by the LuCI build
system, source and delete the uci-defaults themselves upon package insteall,
causing the generic defaults apply code to trigger shell errors like:
.../luci-app-ddns.postinst: .: line 130: can't open './40_luci-ddns'
Rework the generic apply code to check the existence of the uci-defaults
script before trying to source it, use sed to prefilter the list of entries
from the control file and perform the directory change in a subshell,
avoiding the need for cd $OLDPWD.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Generalize the partition discovery in sysupgrade in order to fix sysupgrade
and config backup/recovery on MMC block devices which use a different naming
scheme compared to mtdblock or sd* devices.
The change also adds the find applet to the ramdisk utilities so that upgrade
code can rely on it.
The commit is based on the initial submission by Russell Senior at
http://patchwork.ozlabs.org/patch/625440/ .
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Centralize setting all version information in include/version.mk
* Set RELEASE env variable in include/version.mk instead of toplevel.mk.
Stop exporting the variable.
* Remove hardcoded release name from /etc/banner
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Typo, missing space before ] in previous commit caused shell syntax
failure and incorrect restoration of time.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
dnsmasq maintains dnsmasq.time across reboots and uses it as a means of
determining if current time is good enough to validate dnssec time
stamps. By including /etc/dnsmasq.time as a time source for sysfixtime,
the mechanism was effectively defeated because time was set to the
last time that dnsmasq considered current even though that time is in
the past. Since that time is out of date, dns(sec) resolution would
fail thus defeating any ntp based mechanisms for setting the clock
correctly.
In theory the process is defeated by any files in /etc that are newer
than /etc/dnsmasq.time however dnsmasq now updates the file's timestamp
on process TERM so hopefully /etc/dnsmasq.time is the latest file
timestamp in /etc as part of LEDE shutdown/reboot.
Either way, including /etc/dnsmasq.time as a time source for
sysfixtime is not helpful.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
dnsmasq maintains dnsmasq.time across reboots and uses it as a means of
determining if current time is good enough to validate dnssec time
stamps. By including /etc/dnsmasq.time as a time source for sysfixtime,
the mechanism was effectively defeated because time was set to the
last time that dnsmasq considered current even though that time is in
the past. Since that time is out of date, dns(sec) resolution would
fail thus defeating any ntp based mechanisms for setting the clock
correctly.
In theory the process is defeated by any files in /etc that are newer
than /etc/dnsmasq.time however dnsmasq now updates the file's timestamp
on process TERM so hopefully /etc/dnsmasq.time is the latest file
timestamp in /etc as part of LEDE shutdown/reboot.
Either way, including /etc/dnsmasq.time as a time source for
sysfixtime is not helpful.
- Update the terminal window title with the current directory and hostname, if using an xterm-compatible terminal emulator.
- Add ll, an useful alias to ls.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
The json_select call fails when there are no roles or ports objects in board.json. "json_select .." must not be executed after failing.
This fixes for example LEDs not being set up in /etc/config/system.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Packages may install scripts into /etc/uci-defaults to be executed once
after installation, usually at the first boot of the target. This works
fine if the package was installed to the rootfs during build or using
the ImageBuilder.
If the package is installed using opkg during run-time uci-defaults
were applied only after a reboot of the device. Avoid the need to
reboot by evaluting the package's uci-defaults in default-postinst.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove the public unatteded buildkey from the opkg package to avoid
having hardcoded keys in tree. Use the external keyring package instead
which can be easily updated by users.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Karl Palsson
Jonas Gorski
Mathias Kresin
Felix Fietkau
Daniel Golle
Conn O'Griofa
Etienne CHAMPETIER
Jo-Philipp Wich
Kevin Darbyshire-Bryant
Daniel Dickinson
John Crispin
Hannu Nyman
Vittorio G (VittGam)
Vittorio Gambaletta (VittGam)
John Crispin
Hauke Mehrtens
John Crispin