Removed an eglibc remnant, and while at it, grouped all of the
TOOLCHAIN_PLATFORMs using the same FLAGS together.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefore add all libraries linked by
block-mount and blockd as direct dependencies to the corresponding
binary package definition.
This ensures that block-mount and blockd is automatically rebuilt and
relinked if any of these libraries has its ABI_VERSION updated in the
future.
Fixes: FS#2373
[jow: similar fix for procd and 98.42% of commit message]
Signed-off-by: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
The command line enforced by the kernel is harmful, we want to
use the command line passed from the device tree. This is
especially important for the SQ201, Teltonika RUT and WBD111
which has a console set to 115200n8 and not 19200n8 like all
the others, so their consoles will be confusingly changing
baudrate between boot loader and kernel. The setting in the
device tree corresponds to what the boot loader is using.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch unifies the polled and interrupt-driven gpio_keys code
paths as well implements consistent handling of the debounce
interval set for the GPIO buttons and switches.
Hotplug events will only be fired if
1. The input changes its state and remains stable for the duration
of the debounce interval (default is 5 ms).
2. In the initial stable (no state-change for duration of the
debounce interval) state once the driver module gets loaded.
Switch type inputs will always report their stable state.
Unpressed buttons will not trigger an event for the initial
stable state. Whereas pressed buttons will trigger an event.
This is consistent with upstream's gpio-key driver that uses
the input subsystem (and dont use autorepeat).
Prior to this patch, this was handled inconsistently for interrupt-based
an polled gpio-keys. Hence this patch unifies the shared logic into the
gpio_keys_handle_button() function and modify both implementations to
handle the initial state properly.
The changes described in 2. ) . can have an impact on the
failsafe trigger. Up until now, the script checked for button
state changes. On the down side, this allowed to trigger the
failsafe by releasing a held button at the right time. On the
plus side, the button's polarity setting didn't matter.
Now, the failsafe will only engage when a button was pressed
at the right moment (same as before), but now it can
theoretically also trigger when the button was pressed the
whole time the kernel booted and well into the fast-blinking
preinit phase. However, the chances that this can happen are
really small. This is because the gpio-button module is usually
up and ready even before the preinit state is entered. So, the
initial pressed button event gets lost and most devices behave
as before.
Bisectors: If this patch causes a device to permanently go into
failsafe or experience weird behavior due to inputs, please
check the following:
- the GPIO polarity setting for the button
- the software-debounce value
Run-tested for 'gpio-keys' and 'gpio-keys-polled' on
- devolo WiFi pro 1200e
- devolo WiFi pro 1750c
- devolo WiFi pro 1750x
- Netgear WNDR4700
- Meraki MR24
- RT-AC58U
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [further
cleanups, simplification and unification]
- Support added to bcm2709 subtarget (32 bit).
- 64 bit kernel still requires many hacks on RPi 4B.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
Update the lua5.3 package to build a shared object just like the old lua
package. Ported / recreated the same patch number as the other lua
package. Built and tested library / interpreter on BCM5301X.
Signed-off-by: Colby Whitney <colby.whitney@luxul.com>
This commit fixes a forgotten case in previous commit.
Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
do_upgrade_stage2() isn't really any common code. It isn't used anywhere
except for /sbin/sysupgrade that passes it to the stage2.
Moving its code to separated file also simplifies COMMAND variable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
mt7621 and mt7628 now have the ability to detect memory size
automatically.
Drop memory nodes and let kernel determine memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].
[1]: https://fcc.io/K7S/F7C027
Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch applies sorting to the definitions as whole blocks.
Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Having converted the target to use device compatible, ramips.sh
is obsolete now.
The only remaining entry for the mt7688 evaluation board seems to
be orphaned.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
---
This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.
Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Include "Archer" in compatible as it is part of the device name.
Update Makefile device names where necessary to match compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Eneas U de Queiroz
Moritz Warning
Rafał Miłecki
Petr Štetiar
David Bauer
Linus Walleij
Álvaro Fernández Rojas
Felix Fietkau
Hans Dedecker
Hauke Mehrtens
Colby Whitney
Chuanhong Guo
Daniel Golle
Adrian Schmutzler
Chen Minqiang
Luis Araneda