Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The swconfig switch led driver has the ability to switch
between a "link, rx and/or tx" mode. However, this feature
was not implemented in uci, the led init script and
config_generate.
This patch adds a seventh parameter to the
ucidef_set_led_switch() function. The accepted values for
this parameter are: link, rx and tx.
Any permutations of these three values are supported, as
long as they are properly encased with quotes.
If the parameter is not specified it will default to "all"
(link rx tx).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The previous refactoring of ucidef_set_interface() removed the protocol
selection heuristic which breaks the networking defaults for the majority
of boards.
Re-add the protocol selection and rename two bad "proto" references to
the expected "protocol" value.
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is a rework of previously submitted patch reworking
ucidef_set_interface_raw [1]. Here, keep the idea but instead
make _ucidef_set_interface more generic and use it instead of
ucidef_set_interface_raw.
Also change the users like ucidef_set_interface_lan and others.
[1] https://patchwork.ozlabs.org/patch/844961/
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
The offset and factor are only related for LEDs which can have
different brightness values. But binary LEDs are more common and don't
require any further configuation than setting the factor to 1.
Use offset = 0 and factor = 1 in case nothing else is specified.
Signed-off-by: Mathias Kresin <dev@kresin.me>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Instead of only using tagged CPU port configurations when more than one VLAN
is present on the switch, always emit tagged configurations unless a board
explicitely opts out of this behaviour by using the previously introduced
[0-9]u@netdev syntax.
Emitting default tagged configurations has the following benefits:
- Relation of switch vlans to netdevs is easier to understand, especially
for multi-cpu-port switches
- Adding additional VLANs (e.g. to break out a LAN port for other purposes)
becomes easier as users are not forced to change the existing untagged
VLAN to tagged and the existing ifname notation from ethX to ethX.Y
anymore, drastly reducing the likelyhood of soft-bricks.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce support for a new [0-9]u@netdev syntax to ucidev_add_switch() to let
board.d network files request default network switch configurations which do
not use tagged CPU ports.
This commit itself has no effect on generated configurations at the moment
since we still emit untagged configurations by default but it allows boards to
opt-out from default tagged configs in case we start emitting tagged settings
by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"
This adds a proper object to the board.json, e.g.
"usb": {
"name": "USB",
"type": "usbport",
"sysfs": "devicename:colour:function",
"ports": [
"usb1-port1",
"usb2-port1"
]
}
and supports translating it into uci section.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch adds extra parameter to switch LED trigger initialization
functions. New functionality maintains backward compatibility, so
calling functions without setting new speed_mask parameter works
as expected.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48776
oneshot and timer have the same configuration options, just a different
trigger name.
Signed-off-by: Karl Palsson <karlp@etactica.com>
SVN-Revision: 48770
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42848
Add a third argument to ucidef_set_interface_raw, which is specifying
the protocol.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42665
This allows services to bind to it at boot time instead of waiting for a
cable to be plugged in
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40773
Petr Štetiar
Christian Lamparter
Jo-Philipp Wich
Roman Yeryomin
Martin Schiller
Mathias Kresin
Alberto Bursi
Rafał Miłecki
Jonas Gorski
John Crispin
Felix Fietkau
Jo-Philipp Wich
Jonas Gorski
Steven Barth
Florian Fainelli
Luka Perkov
Gabor Juhos