Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The two phy operation mode where one phy is assigned to an interface
without lantiq,* device tree property and the other phy is assigned to
an interface with the lantiq,wan device property was broken with the
multicast package leaks between vlans fixes.
Move the multicast packages relevant portmap settings to the condition
which handles multicast packages for better readability.
Replace the priv->port_map based port_map only for the interface which
has the lantiq,switch device tree property set, to allow tagged
multicast packages in two phy mode where the lantiq,switch device tree
property isn't used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The port is labeled as wan and was only used as lan port because of the
"tx ring full" issues fixed with 8f02f7c.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.
The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.
If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.
Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Explicitely disable X2APIC support on legacy targets since the targeted
processor types do not support it anyway there.
Fixes FS#285.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The umdns init script includes function/network.sh globally, outside of any
service procedure. This causes init script activation to fail in buildroot
and IB context if umdns is set to builtin.
Additionally, the network.sh helper is not actually used.
Drop the entire include in order to repair init script activation in build
host context. Fixes FS#658.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is a cumulative backport of multiple dnsmasq update commits in master.
Drops three LEDE specific patches which are included upstream and another
patch which became obsolete. Remaining LEDE specific patches are rebased.
Fixes FS#766 - Intermittent SIGSEGV crash of dnsmasq-full.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Brings the following changes:
22f041e18df0 Extend StandardEject sequence to include LUN 1
61fdf7e9b1cc cmake: Search for libjson-c
2769852e76b5 cmake: Find libubox/blobmsg_json.h
8a47c4b6649f add TargetClass support
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The previous CVE bugfix commit did not adjust PKG_RELEASE, therefor the
fixed samba package does not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
Ref: https://forum.lede-project.org/t/sambacry-are-lede-devices-affected/3972/4
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest Git HEAD in order to import a number of fixes and other
improvements:
a4d98ae options: remove stray continue statement
3d2c18a options: improve handling of negations when parsing space separated values
0e5dd73 iptables: support -i, -o, -s and -d in option extra
4cb06c7 ubus: increase ubus network interface dump timeout
e5dfc82 iptables: add exception handling
f625954 firewall3: add check_snat() function
7d3d9dc firewall3: display the section type for UBUS rules
53ef9f1 firewall3: add UBUS support for include scripts
5cd4af4 firewall3: add UBUS support for ipset sections
02d6832 firewall3: add UBUS support for forwarding sections
0a7d36d firewall3: add UBUS support for redirect sections
d44f418 firewall3: add fw3_attr_parse_name_type() function
e264c8e firewall3: replace warn_rule() by warn_section()
6039c7f firewall3: check the return value of fw3_parse_options()
c328d1f build: use -Wno-format-truncation instead of -Wno-error=format-truncation
e06e537 utils: replace sprintf use with snprintf to avoid overflows
533f834 build: disable the format-truncation warning error to fix gcc 7 build errors
e751cde zones: drop outgoing invalid traffic in masqueraded zones
d596f72 rules: fix UCI context in error reporting
1d0564c ubus: fix interface name and proto lookup
82ccd9e firewall3: fix handling of UTC times
1949e0c iptables: support xtables API > 11
Fixes FS#548, FS#640, FS#806, FS#811.
Ref: https://forum.lede-project.org/t/nat-leakage-on-tl-wr1043nd-v4/1712
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit contains the following changes
- Use local shell var where appliable
- The $(sort $$$$$$$$mods) call will have no expected effect
- Avoid EEXIST when creating symlinks in /etc/modules-boot.d/
- Avoid duplicate arguments for insert_modules() in postinst-pkg
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Bump the 17.01 tree kernel to 4.4.69. Trunk 4.4 and 17.01 4.4 have diverged, talked this
through with jow, he was okay with a clean diff against 17.01 and not a backported trunk
patch.
The following patches were applied upstream:
* 062-[1-6]-MIPS-* series
* 042-0004-mtd-bcm47xxpart-fix-parsing-first-block
Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup, as
it was incorrectly included upstream thus dropped from LEDE, but subsequently
reverted upstream. Thanks to Kevin Darbyshire-Bryant for pointing me to it.
Compile-tested on: ar71xx, ramips/mt7621, x86/64.
Run-tested on: ar71xx, ramips/mt7621, x86/64.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
binutils 2.27 checks if the target compiler supports -Wstack-
usage=262144, and also uses this setting for the host compiler. If the
host compiler is gcc < 4.9 binutils build will fail. This backports 2
commits which are fixing this problem for binutils 2.28.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix build of scriptreplay with uClibc.
Some parts of the libm detection were backported to 2.29.2, but some
parts were missing, which are added here. This patch is needed when
libm is a separate library, this is not needed for LEDE master, because
libm is there integrated in the libc for uClibc and musl.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
- Security: Fix double-free in server TCP listener cleanup A double-free
in the server could be triggered by an authenticated user if dropbear is
running with -a (Allow connections to forwarded ports from any host)
This could potentially allow arbitrary code execution as root by an
authenticated user. Affects versions 2013.56 to 2016.74. Thanks to Mark
Shepard for reporting the crash.
CVE-2017-9078 https://secure.ucc.asn.au/hg/dropbear/rev/c8114a48837c
- Security: Fix information disclosure with ~/.ssh/authorized_keys
symlink. Dropbear parsed authorized_keys as root, even if it were a
symlink. The fix is to switch to user permissions when opening
authorized_keys
A user could symlink their ~/.ssh/authorized_keys to a root-owned file
they couldn't normally read. If they managed to get that file to contain
valid authorized_keys with command= options it might be possible to read
other contents of that file.
This information disclosure is to an already authenticated user.
Thanks to Jann Horn of Google Project Zero for reporting this.
CVE-2017-9079 https://secure.ucc.asn.au/hg/dropbear/rev/0d889b068123
Refresh patches, rework 100-pubkey_path.patch to work with new
authorized_keys validation.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This includes following changes:
0e8b948 Support specifying instance name in JSON file
49fdb9f Support PTR queries for a specific service
26ce7dc Allow filtering with instance name in service_reply
920c62a Store instance name in the struct service
ff09d9a Rename service_name function to the service_instance_name
64f78f1 Rename mdns_hostname variable to the umdns_host_label
Previous package update pulled commit 70c66fbbcde86 ("Fix sending
replies to PTR questions") which introduced a regression which this
update fixes.
Fixes: 474c31a20d ("umdns: update to the version 2017-03-21")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This model also contains few partitions non-discoverable partitions we
need to "protect". Othen than that it uses non-deprecated serial entry
in DTS that doesn't work with LEDE so we need to workaround it as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refer to LINUX_KARCH instead of ARCH when bundling DTS files in the image
builder tarball.
While we're at it, also dereference symbolic links when copying as some
kernel architectures contain symbolic links in their DTS directories.
This fixes aarch64 imagebuilders such as brcm2708/bcm2710 ones in particular
as the kernel refers to "aarch64" as "arm64" internally.
Ref: https://forum.lede-project.org/t/lede-image-builder-problem/3680
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some files (e.g. /etc/dropbear) need to be owned by root. Add cpio
option to ensure that.
Other image types (at least targz and squashfs) already have this.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update OpenVPN to 2.4.1
Remove 200-small_build_enable_occ.patch as it's included upstream.
Refresh patches
Add mirror and switch to HTTPS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Mathias Kresin
Felix Fietkau
Jo-Philipp Wich
Alberto Bursi
Karl Vogel
Philip Prindeville
Piotr Dymacz
Etienne Haarsma
Julian Labus
Florian Fainelli
Matthias Schiffer
Nick Lowe
Thomas Reifferscheid
Yousong Zhou
Hauke Mehrtens
Stijn Segers
Hauke Mehrtens
Kevin Darbyshire-Bryant
Stijn Tintel
Rafał Miłecki
Michal Sojka
Steffen Weinreich
Daniel Engberg
Martin Schiller