Significant performance/stability improvements for MT76x2 and MT7603.
Adds LED support.
Changes:
2895775 mt76x2: mcu: remove unused parameter in mt76x2_mcu_msg_alloc signature
1dae8f0 mt7603: mcu: remove unused parameter in mt7603_mcu_msg_alloc() signature
5e49aa9 Fix errors found by cppcheck
1b8c8a0 mt7603: add LED definition registers
4d83561 mt76x2: add LED register definitions
2f40e4a mt76x2: Support using PCI ID as chip ID
27c64bc mt76: add led support using mac80211 led framework
dfd64fc mt76x2: init: add ma80211 led callbacks
215edf1 mt7603: init: add ma80211 led callbacks
9d36ff2 mt76x2: Add PCI identifier for MT7602
0b7984e mt7603: remove unnecessary mcu register read function
f5498d2 debugfs: add support for changing the LED pin
8e453b3 mac80211: move DT led configuration to the "led" child node
8f1673a mt76x2: limit client WCID entries to 0-127
f9d9c22 mt76x2: clear drop flag for all WCIDs on init
0dd8b68 mt76x2: clear per-WCID tx rate lookup register
3e5afe7 mt76x2: add helper function for setting drop mask
941555b mt76x2: clear drop mask when sending a PS response
7dfb354 mt76: increase rx ring size for mt76x2
73902dc mt76x2: add rx statistics registers
fe79816 mt76x2: fix LNA gain register annotation
cc588c5 mt76x2: sync channel gain value with latest reference driver
60a4d67 mt76x2: implement dynamic AGC tuning based on false packet detection count
4bc9aa9 mt76x2: add more gain tuning based on the latest reference driver
0a0d16f mt76x2: sync tx power related values with reference driver
8c821aa mac80211: add missing include
82acc85 mt7603: add missing include required on newer kernels
2c1a77c mt76x2: fix transmission of encrypted management frames
0532315 mt76x2: increase OFDM SIFS time
1acde21 mt76x2: add channel argument to eeprom tx power functions
58364a2 mt76x2: initialize channel power limits
c2bd89e mt76x2: convert between per-chain tx power and combined output
e7eaa7c mt7603: rename mt7603_mac_reset to mt7603_pse_reset
ea4c2a1 mt7603: rename MT_PSE_RESET register
c86c3a0 mt7603: remove watchdog reset on interface stop
4490f93 mt7603: remove WARN_ON_ONCE for workaround checks
3075059 mt7603: simplify PSE reset
4ed7e07 mt7603: warn if PSE reset fails
7dc8db1 mt7603: clean up dma debug reads
41e6a04 mt7603: make mt7603_mac_watchdog_reset() static
dc7a351 mt7603: clear wtbl PS bit for powersave responses
123acf2 mt7603: set tx-skip flag for powersave clients
7dd2a9e mt7603: initialize wtbl ps flag on station add
86ddef3 mt76x2: remove some harmless WARN_ONs in tx status and rx path
e326bc2 mt7603: remove some harmless WARN_ONs in rx path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The short log of changes since the 2016-06-10 release is below.
Jouni Malinen (1):
wireless-regdb: Remove DFS requirement for India (IN)
Ryan Mounce (1):
wireless-regdb: Update rules for Australia (AU) and add 60GHz rules
Seth Forshee (2):
wireless-regdb: Update 5 GHz rules for Canada
wireless-regdb: update regulatory.bin based on preceding changes
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
(cherry picked from commit 8b12e62e9c)
Backport required DT changes from commit dabdd123c9.
Significantly improves stability and performance for MT76x2 and MT7603
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit b428f45c06.
If the optimized firmware download is disabled, the xdsl subsystem
hangs in the "idle request" state after physically disconnecting and
reconnecting the xdsl modem from the line.
It might fix the failing line init on boot as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With ltq-vdsl-mei 1.5.17.6 an optimized firmware download was added and
enabled by default. As soon as the optimized firmware download is
enabled, a watchdog based reboot is trigger between 24h to 48h of
uptime if the board isn't connected to a xdsl line.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a backport form drv_dsl_cpe_api-4.18.10 and fixes some PM
thread handling issues which lead to high system load and watchdog
trigger within 1h of uptime for boards not connected to a xdsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
The tftp and irc netfilter modules are provided by nf-nathelper-extra
and not by nf-nathelper.
Signed-off-by: Uwe Arnold <donvipre@gmail.com>
[move the irc module as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: moved changes into a separate patch]
Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: moved changes into a separate patch]
Some of our local patches have been accepted upstream. And there are
some more relevant changes (mostly for rt2800usb). Import them and
rebase our remaining local patches on top.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Introduce RT6352 instead of matching against RF7620.
Clean up channel setting rfvals.
Port bandwidth filter calibration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So here is another round of improvements for MT7620 WiFi.
This commit fixes a few significant issues related to TX_PWR_CFG_x and
TX_ALC and also makes the code more readable by adding register
descriptions for things added for MT7620 and use the usual bit-field
access macros and the now defined macros instead of plain bit-ops and
magic numbers.
Properly describe EEPROM_TARGET_POWER at word 0x68 (== byte 0xD0) and
thereby fix internal TXALC which would otherwise just read
out-of-bounds of the EEPROM map.
Split-out tx-power/ALC related stuff into an additional function.
Fix VCO calibration, it was carried out properly in the channel
switching but incomplete in the actual VCO calibration function.
Also there is no need to trigger VCO calibration in channel switching,
the VCO calibration function is already being called at this point.
Remove it from channel switching function to avoid redundant code.
The TX power calibration differs significantly from all other
Mediatek/Ralink chips: They finally allow 0.5dB steps stored as 8-bit
values for (almost) each bitrate -- and promptly ran out of space and
for some reason didn't want to change the EEPROM layout. The hence
opted for a scheme of sharing values for some adjecent bitrates and
a highly over-complicated (or obfuscated?) way to populate the
TX_PWR_CFG_x registers with the values stored in the EEPROM.
The code here now looks much less complicated than what you see in the
vendor's driver, however, it does the exact same thing:
bGpwrdeltaMinus is a constant and always TRUE, hence half of the
code was dead. Gpwrdelta is always 0 (rather than using the value read
from the EEPROM). What remains is some very grotesque effort to avoid
0x20, probably some hardware bug related to some misunderstanding of
what a singed 8-bit value is (imagine: if it was a signed 6-bit value
then someone could believe that 0x20 == 0x0). And then they didn't
clean it up once they later on anandonned that whole story of having a
constant offset for 40 MHz channels and just set the offset to be
constant 0 -- there is no effort for avoiding 0x20 for the 20 MHz
values stored in the EEPROM, hence that's probably just a forbidden
value in the EEPROM specs and won't appear anyway...
Anyway, the whole thing felt like solving some college math test
where in the end everything cancels out and the result equals 0 ;)
To make sure that channel bandwidth power compensation really doesn't
need to be taken care of, output a warning when the corresponding
value stored in the EEPROM is non-zero.
Also there is no apparent reason to refrain from initializing RFCSR
register 13, it doesn't fail what-so-ever.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a device uses the default EEPROM code, typically only the main CTLs
are valid, and they do not apply properly when switching to a different
regulatory domain. If the regdomain deviates from the EEPROM one, force
the world roaming regdomain to ensure that power limits are sane
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds option to build kernel module and firmware packages
for a Marvell 8887 SDIO Wireless device
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for the PCB LEDs and Reset Button found on the PC
Engines APU2/APU3 embedded boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This adds support for the SuperIO chip nct5104d found on the PC Engines
APU boards, which allows for a handful of additional ports, such as 2x
additional UART pinouts, enabling an external watchdog (no driver for
this functionality yet), and 16 GPIO pins. More info can be found at
https://pcengines.ch/ht_gpio.htm
Thanks to @feckert for helping package this.
Cc: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The subtarget on which the driver still depends was removed with
dee8986b95 because it was unmaintained
for a long time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is required for default wireless configuration of malta target to
work out of the box again. Fixes "77ece30e: hostapd: Add ability to
specify that that wireless driver supports 802.11ac"
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Includes the following changes:
9edff13abd mac80211: disable potentially harmful PS software retry for A-MPDU sessions
75216a76b0 mac80211: backport upstream fix for CSA in IBSS mode
368cc8ef47 mac80211: update brcmfmac backporting brcmf_err cleanups
66a63d25c4 mac80211: fix build on linux 3.18
9eacb9d7fc rt2x00: mt7620: lots of improvements
fd94fa61a7 mac80211: brcmfmac: update Raspberry Pi patches for linux 4.9
649e766a64 mac80211: update to wireless-testing 2017-01-31
47540afa5d ath9k: add a warning to the tx99 config option
b367eef21d mac80211: rt2x00: add support for external LNA on MT7620
9200e168f2 mac80211: move (& update) upstream accepted brcmfmac patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The driver had a bug when calculating the rateset. This resolves
that and allows full VHT mcs rates on 2x2 hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This patch splits `kmod-mt76` into three separate packages:
`kmod-mt76-core`, `kmod-mt76x2` and `kmod-mt7603`. By making
`kmod-mt76` a metapackage containing these new packages,
the previous behaviour of including all drivers and firmware
is left unchanged, unless explicitly unselected in
`DEVICE_PACKAGES`.
This splitting is especially beneficial for devices with
small flash chips, since the `kmod-mt76` package currently
requires ~160K on squashfs (after compression).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Effects of the bugs could include memory corruption, tx hangs, kernel
crahes, possibly other things as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
I needed a moment to figure out relation between this patchset and the
nl80211: fix validation of scheduled scan info for wowlan netdetect
It appears nl80211 commit will go on top of brcmfmac changes so it's
safe to backport these patches.
One patch that was excluded is commit 2a2a5d1835b6 ("brcmfmac: add
.update_connect_params() callback") as it depends on missing commit
088e8df82f91 ("cfg80211: Add support to update connection parameters").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau
Stijn Tintel
Ryan Mounce
Mathias Kresin
Martin Schiller
Lorenzo Santina
Uwe Arnold
Jo-Philipp Wich
Matthias Schiffer
Yousong Zhou
Steffen Weinreich
Piotr Dymacz
Tomislav Požega
Daniel Golle
Jonas Gorski
Álvaro Fernández Rojas
Henryk Heisig
Hsing-Wang Liao
Chris Blake
Koen Vandeputte
Ben Greear
Joseph C. Lehner
Sven Eckelmann
Rafał Miłecki