Fixes package libcurl build issue :
Package libcurl is missing dependencies for the following libraries:
libzstd.so.1
Suggested-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Abort the dhcp-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't cause a dnsmasq reload, thus dhcp won't become active
on this interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
"type" is already used as a common option for all protocols types, so
using the same option name for the map type makes the configuration
ambiguous. Luci in particular adds controls for both options and sees
errors when reading the resulting configuration.
Use "maptype" instead, but still fallback to "type" if "maptype" is not
set. This allows configurations to migrate without breaking old
configurations.
This addresses FS#3287.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The is no reason to catch the output by $() and then echo it again.
Remove the useless echos.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy map version based on the IPv6 Interface Identifier in
draft-ietf-softwire-map-03 was typically used by uncommenting the LEGACY
variable in the map.sh file, which is not ideal. A proper configuration
option is needed instead.
The IPv6 Interface Identifier format described in the draft was
eventually changed in RFC7597, but is still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If not needed, disabling scp allows for a nice size reduction.
Dropbear executable size comparison:
153621 bytes (baseline)
133077 bytes (without scp)
In other words, we trim a total of 20544 bytes.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
677aa53 Fix -W option for pppoe-discovery utility (#157)
115c419 Accept Malformed Windows Success Message (#156)
5bdb148 pppd: Add documentation of stop-bits option to pppd man page (#154)
2a7981f Add ipv6cp-accept-remote option
0678d3b pppd: Fix the default value for ipv6cp-accept-local to false
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The hostapd configuration logic is supposed to accept "option key" as
legacy alias for "option auth_secret". This particular fallback option
failed to work though because "key" was not a registered configuration
variable.
Fix this issue by registering the "key" option as well, similar to the
existing "server" nad "port" options.
Ref: https://github.com/openwrt/openwrt/pull/3282
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If an existing "wpa_psk_file" is passed to hostapd, the "key" option may
be omitted.
While we're at it, also improve the passphrase length checking to ensure
that it is either exactly 64 bytes or 8 to 63 bytes.
Fixes: FS#2689
Ref: https://github.com/openwrt/openwrt/pull/3283
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add package which provides size optimized wpad with support for just
WPA-PSK, SAE (WPA3-Personal), 802.11r and 802.11w.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[adapt to recent changes, add dependency for WPA_WOLFSSL config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Before this commit, if uci option "dnssec" was set, we pass "--dnssec"
and friends to dnsmasq, let it start and decide whether to quit and
whether to emit message for diagnosis
# dnsmasq --dnssec; echo $?
dnsmasq: DNSSEC not available: set HAVE_DNSSEC in src/config.h
1
DNSSEC as a feature is different from others like dhcp, tftp in that
it's a security feature. Better be explicit. With this change
committed, we make it so by not allowing it in the first in the
initscript, should dnsmasq later decides to not quit (not likely) or
quit without above explicit error (unlikely but less so ;)
So this is just being proactive. on/off choices with uci option
"dnssec" are still available like before
Link: https://github.com/openwrt/openwrt/pull/3265#issuecomment-667795302
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
With the introduction of the generic OpenVPN hotplug mechanism, wrapped
--up and --down scripts got the wrong amount and order of arguments passed,
breaking existing configurations and functionality.
Fix this issue by passing the same amount of arguments in the same expected
order as if the scripts were executed by the OpenVPN daemon directly.
Ref: https://github.com/openwrt/openwrt/pull/1596#issuecomment-668935156
Fixes: 8fe9940db6 ("openvpn: add generic hotplug mechanism")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This package provides the necessary files to translate `config dsa_vlan`
and `config dsa_port` sections of `/etc/config/network` into appropriate
bridge vlan filter rules.
The approach of the configuration is to bridge all DSA ports into a logical
bridge device, called "switch0" by default, and to set VLAN port membership,
tagging state and PVID as specified by UCI on each port and on the switch
bridge device itself, allowing logical interfaces to reference port VLAN
groups by using "switch0.N" as ifname, where N denotes the VLAN ID.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
212f836 ubus: rename JSON-RPC format related functions
628341f ubus: use local "blob_buf" in uh_ubus_handle_request_object()
9d663e7 ubus: use BLOBMSG_TYPE_UNSPEC for "params" JSON attribute
77d345e ubus: drop unused "obj" arguments
8d9e1fc ubus: parse "call" method params only for relevant call
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* compat: rhel 8.3 beta removed nf_nat_core.h
* compat: ipv6_dst_lookup_flow was ported to rhel 7.9 beta
This compat tag adds support for RHEL 8.3 beta and RHEL 7.9 beta, in addition
to RHEL 8.2 and RHEL 7.8. It also marks the first time that
<https://www.wireguard.com/build-status/> is all green for all RHEL kernels.
After quite a bit of trickery, we've finally got the RHEL kernels building
automatically.
* compat: allow override of depmod basedir
When building in an environment with a different modules install path, it's
not possible to override the depmod basedir flag by setting the DEPMODBASEDIR
environment variable.
* compat: add missing headers for ip_tunnel_parse_protocol
This fixes compilation with some unusual configurations.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for packages by the
corresponding ip commands now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update the openvpn sample configurations to use modern options in favor
of deprecated ones, suggest more sane default settings and add some
warnings.
* Add tls_crypt and ncp_disable to the sample configuration
* Replace nsCertType with remote_cert_tls in client sample configuration
* Comment out "option compress", compression should not be preferred
* Advise 2048-bit Diffie-Hellman parameters by default
* Add warnings about compression and use of Blowfish (BF-CBC)
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
The wg utility compiles and runs without issues in MIPS16 mode, despite setting
PKG_USE_MIPS16:=0 in the makefile. Let's remove this, allowing for a substantial
size reduction of the wg executable. Since wg is a just a configuration utility,
it shouldn't be performance-critical, as the crypto heavy-lifting is done on the
kernel side.
wg sizes for both modes:
MIPS32: 64309 bytes
MIPS16: 42501 bytes
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
The current selection of DRIVER_MAKEOPTS and TARGET_LDFLAGS is
exceptionally hard to read. This tries to make things a little
easier by inverting the hierarchy of the conditions, so SSL_VARIANT
is checked first and LOCAL_VARIANT is checked second.
This exploits the fact that some of the previous conditions were
unnecessary, e.g. there is no hostapd-mesh*, so we don't need
to exclude this combination.
It also should make it a little easier to see which options are
actually switched by SSL_VARIANT and which by LOCAL_VARIANT.
The patch is supposed to be cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For a few packages, the current TITLE is too long, so it is not
displayed at all when running make menuconfig. Despite, there is
no indication of OpenSSL vs. wolfSSL in the titles.
Thus, this patch adjusts titles to be generally shorter, and adds
the SSL variant to it.
While at it, make things easier by creating a shared definition for
eapol-test like it's done already for all the other flavors.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Drop outdated and by now broken patchset originally supplied by
Peter Oh in August 2018 but never merged upstream.
Instead add the more promissing rework recently submitted by
Markus Theil who picked up Peter's patchset, fixed and completed it
and added support for HE (802.11ax) in mesh mode.
This is only compile tested and needs some real-life testing.
Fixes: FS#3214
Fixes: 167028b750 ("hostapd: Update to version 2.9 (2019-08-08)")
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Fixes: 017320ead3 ("hostapd: bring back mesh patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The following patches:
* 972-ath10k_fix-crash-due-to-wrong-handling-of-peer_bw_rxnss_override-parameter.patch
* 973-ath10k_fix-band_center_freq-handling-for-VHT160-in-recent-firmwares.patch
are replaced by this commit in the upstream kernel:
* 3db24065c2c8 ("ath10k: enable VHT160 and VHT80+80 modes")
The following patches were applied upstream:
* 001-rt2800-enable-MFP-support-unconditionally.patch
* 090-wireless-Use-linux-stddef.h-instead-of-stddef.h.patch
The rtw88 driver is now split into multiple kernel modules, just put it
all into one OpenWrt kernel package.
rtl8812au-ct was patched to compile against the mac80211 from kernel
5.8, but not runtime tested.
Add a patch which fixes ath10k on IPQ40XX, this patch was send upstream
and fixes a crash when loading ath10k on this SoC.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If using a configuration file for OpenVPN, allow overriding name of the
interface. The reason is that then people could use configuration file
provided by VPN provider directly and override the name of the interface
to include it in correct firewall zone without need to alter the
configuration file.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit c93667358515ec078ef4ac96393623ac084e5c9e)
Split out code that parses openvpn configuration file into separate file
that can be later included in various scripts and reused.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit 86d8467c8ab792c79809a08c223dd9d40da6da2e)
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Similar to wireguard, vxlan can configure multiple peers or add specific
entries to the fdb for a single mac address.
While you can still use peeraddr/peer6addr option within the proto
vxlan/vxlan6 section to not break existing configurations, this patch
allows to add multiple sections that conigure fdb entries via the bridge
command. As such, the bridge command is now a dependency of the vxlan
package. (To be honest without the bridge command available, vxlan isn't
very much fun to use or debug at all)
Field names are taken direclty from the bridge command.
Example with all supported parameters, since this hasn't been documented so
far:
config interface 'vx0'
option proto 'vxlan6' # use vxlan over ipv6
# main options
option ip6addr '2001:db8::1' # listen address
option tunlink 'wan6' # optional if listen address given
option peer6addr '2001:db8::2' # now optional
option port '8472' # this is the standard port under linux
option vid '42' # VXLAN Network Identifier to use
option mtu '1430' # vxlan6 has 70 bytes overhead
# extra options
option rxcsum '0' # allow receiving packets without checksum
option txcsum '0' # send packets without checksum
option ttl '16' # specifies the TTL value for outgoing packets
option tos '0' # specifies the TOS value for outgoing packets
option macaddr '11:22:33:44:55:66' # optional, manually specify mac
# default is a random address
Single peer with head-end replication. Corresponds to the following call
to bridge:
$ bridge fdb append 00:00:00:00:00:00 dev vx0 dst 2001:db8::3
config vxlan_peer
option vxlan 'vx0'
option dst '2001:db8::3' # always required
For multiple peers, this section can be repeated for each dst address.
It's possible to specify a multicast address as destination. Useful when
multicast routing is available or within one lan segment:
config vxlan_peer
option vxlan 'vx0'
option dst 'ff02::1337' # multicast group to join.
# all bum traffic will be send there
option via 'eth1' # for multicast, an outgoing interface needs
# to be specified
All available peer options for completeness:
config vxlan_peer
option vxlan 'vx0' # the interface to configure
option lladdr 'aa:bb:cc:dd:ee:ff' # specific mac,
option dst '2001:db8::4' # connected to this peer
option via 'eth0.1' # use this interface only
option port '4789' # use different port for this peer
option vni '23' # override vni for this peer
option src_vni '123' # see man 3 bridge
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
vxlan can be configured without a peer address. This is used to prepare
an interface and add peers later.
Fixes: FS#2743
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
This fixes a nasty problem introduced in 2.81 which causes random
crashes on systems where there's significant DNS activity over TCP. It
also fixes DNSSEC validation problems with zero-TTL DNSKEY and DS
records.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This file is always present because it is part of the ltq-dsl-base
package on which these packages depend.
This check would not have been necessary in the past, because the script
was part of the TARGET_LANTIQ on which these packages also depend.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.
This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.
For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".
This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.
Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. To achieve
that, PKG_VERSION is removed there, bumping PKG_RELEASE where
necessary to ensure the resulting package version string is bigger
than before.
During adjustment, one has to make sure that the new resulting composite
package version will not be considered "older" than the previous one.
A useful tool for evaluating that is 'opkg compare-versions'. In
principle, there are the following cases:
1. Sole PKG_VERSION replaced by sole PKG_RELEASE:
In this case, the resulting version string does not change, it's
just the value of the variable put in the file. Consequently, we
do not bump the number in these cases so nobody is tempted to
install the same package again.
2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE:
In this case, the resulting version string has been "version-release",
e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just
need to be higher than the previous PKG_VERSION.
For the cases where PKG_VERSION has always sticked to "1", and
PKG_RELEASE has been incremented, we take the most recent value of
PKG_RELEASE.
Apart from that, a few packages appear to have developed their own
complex versioning scheme, e.g. using x.y.z number for PKG_VERSION
_and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION
(adb-enablemodem, wwan). I didn't touch these few in this patch.
Cc: Hans Dedecker <dedeckeh@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Andre Valentin <avalentin@marcant.net>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Steven Barth <steven@midlink.org>
Cc: Daniel Golle <dgolle@allnet.de>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bumping package version has been overlooked in a previous commit.
While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter
is meant for upstream version number only.
(The effective version string for the package would be "3" in both
cases, so there is no harm done for version comparison.)
Fixes: 0453c3866f ("vxlan: fix udp checksum control")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, passing "rxcsum" and "txcsum" had no effect.
Fixes: 95ab18e012 ("vxlan: add options to enable and disable UDP
checksums")
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Feature detection doesn't recognize ipset v7 use on kernel v5.x systems
and thus disables the tc ematch function em_ipset.
- backport patch:
* 002-configure-support-ipset-v7.patch:
650591a7a70c configure: support ipset version 7 with kernel version 5
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Recent iproute2 5.x versions modified the symbols resolved for plugins,
causing "tc .. action xt .." to fail. Update the list of symbols to fix.
Fixes: b61495409b ("iproute2: tc: reduce size of dynamic symbol table")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This release brings parity with the commits Linus released a few hours
ago into 5.8-rc5.
* receive: account for napi_gro_receive never returning GRO_DROP
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
* device: implement header_ops->parse_protocol for AF_PACKET
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
* queueing: make use of ip_tunnel_parse_protocol
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
* compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops
These are required for moving wg_examine_packet_protocol out of
wireguard and into upstream.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
New script for comgt. Should help to fetch balance or any additional information with USSD.
This script uses the standard AT command which should be supported by all modems.
Run-tested on: Mikrotik wAP LTE KIT
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
[fixed from/sob]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hauke Mehrtens
Josef Schlehofer
Hans Dedecker
David Bauer
Remi NGUYEN VAN
Adrian Schmutzler
Rui Salvaterra
Daniel Golle
Jo-Philipp Wich
Petr Štetiar
Yousong Zhou
Rafał Miłecki
Jason A. Donenfeld
Magnus Kroken
Michal Hrusecky
Kevin Darbyshire-Bryant
Johannes Kimmel
Martin Schiller
Martin Schiller
Tony Ambardar
Kirill Lukonin