Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Certain boards have limitations on U-Boot that prevent flashing
of images where the kernel size exceeds a threshold, yet
sysupgrade can sucessfully manage larger kernels. The current
check-size will remove the target artifact if its total size
exceeds the threshold. If applied after append-kernel,
it will remove the kernel, but the remaining image-assembly
steps will continue, resulting in an image without a kernel
that is likely unbootable.
By defining check-kernel-size, it is now possible to prevent release
of such unbootable images through a construct similar to:
IMAGE/factory.img := append-kernel | pad-to $$$$(GL_UBOOT_UBI_OFFSET) | \
append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Setting CONFIG_IPK_FILES_CHECKSUMS=y causes sha256 checksum files to be
included with the packages to check for corruption. This commit fixes two
issues:
- /sbin/pkg_check was being removed incorrectly if IPK_FILES_CHECKSUMS=y
- checksums were being saved in the wrong file
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Package new kmods "nf_tables_set" and "nft_objref" which got introduced
with kernel 4.18 and restrict the old "nft_set_rbtree" and "nft_set_hash"
modules to sub-4.18 versions.
Also reorder the nftables related netfilter.mk entries alphabetically
while touching this code section.
Fixes: FS#2699
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2699#comment7450
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This tristate choose allows to select to build only some applications
with PIE enabled. On MIPS binaries are getting about 30% bigger when PIE
is activated for the, which is a huge increase.
Network exposed applications like dnsmasq should then be build with PIE
enabled, but some applications which are normally not parsing data from
the network do not have it activated. The regular option should give a
good trade off between extra flash and RAM memory usage and security.
This changes the default from building no applications with PIE to build
some specifically marked applications with PIE enabled. This option is
only activated for targets with bigger flash and RAM to not consume
extra memory on the very small targets. On SDK builds the Regular option
should always be selected, because some tiny targets share the
applications with big targets and only the images for the tiny targets
should contain the none PIE applications, but the images for the normal
targets should use PIE. The shared packages should always use PIE when
it should be normally activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
nft_hash hash falsely removed in commit 97940f8766
("kernel: remove obsolete kernel version switches").
Add the module back, as otherwise the build fails.
Fixes: 97940f8766 ("kernel: remove obsolete kernel version switches")
Signed-off-by: David Bauer <mail@david-bauer.net>
After kernel 4.9 has been removed, this removes all (now obsolete)
kernel version switches that deal with versions before 4.14.
Package kmod-crypto-iv is empty now and thus removed entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Several CMake packages such as log4cplus and protobuf(-c) install to
lib64 instead of lib on some hosts. This completely breaks rpath linking.
Override it globally to avoid fixing each package individually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Currently in OpenWrt, there are two libc++: libstdcpp and uClibc++. The
former is huge and the latter supports only C++98 with some basic support
for C++11. Those C++ versions seem to be specific to the compiler version
libcxx supports C++11 and above while being much smaller than libstdcpp.
On mt7621, these are the sizes of the ipks that I get:
libstdcpp: 460786
libcxx: 182881
uClibc++:67720
libcxx is faster than uClibc++ and is under active development as part of
the LLVM project while uClibc++ is effectively dead.
This PR modifies uclibc++.mk to expose the make menuconfig option. Further
cleanup is beyond the scope of this PR. What that means is, this is not
used by default.
A g++-libcxx wrapper based on the uClibc++ one was added. Works the same
way.
Compile tested with all packages that use uclibc++.mk in their Makefiles
under mipsel_24kc. kismet fails compilation but that package needs to be
cleaned up and updated.
Runtime tested with gddrescue, gdisk, dcwapd, bonnie++, and aircrack-ng
on a TP-Link Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This creates the device variable SOC and adds it to DEFAULT_DEVICE_VARS.
It is supposed to replace target-specific SOC variables like ATH_SOC or
MTK_SOC and thus unify variable names across targets.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Don't put CC_HAS_ASM_GOTO, IS_GCC, IS_CLANG and GCC_VERSION runtime
config options into the kernel configs during reconfiguration as it
makes no sense, since these options should be set at runtime.
Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It seems that there is a missing PKG_SOURCE_URL_FILE support.
This little fix adds the support for packages to change the name of the
downloaded file.
Sometimes it is desirable to change the downloaded archive file name, like
for mitigating name conflicts for different packages (some files on the server
could be named like, e.g. 2018-01-01.tar.gz) or for the cases that there is
no name for the file in the URL (e.g. http://someserver.com/download).
Signed-off-by: Kamil Wcislo <kamil.wcislo@lpnplant.io>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add support for Python 3.8 which was released Oct. 14, 2019.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
[added missing commit description, simplified version check]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit 965f341aa9 ("build: fix host menu config targets using
ncurses") has moved host's path with pkg-config (usually /usr/bin) at
the first place in PATH variable, which is now causing issues with bison
as BISON_PKGDATADIR points into STAGING_DIR_HOST, but the actual bison
used is the one under host PATH (usually /usr/bin/bison), leading to the
following strange failures:
$ make target/linux/clean kernel_menuconfig V=sc
export MAKEFLAGS= ;make -C /somewhere/linux-4.19.81 menuconfig
make -f ./scripts/Makefile.build obj=scripts/kconfig menuconfig
...
bison -oscripts/kconfig/zconf.tab.c -t -l scripts/kconfig/zconf.y
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/bison.m4': No such file or directory
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/c-skel.m4': No such file or directory
...
gcc -Wp,-MD,scripts/kconfig/.zconf.tab.o.d <...snip...> -o scripts/kconfig/zconf.tab.o scripts/kconfig/zconf.tab.c
gcc: error: scripts/kconfig/zconf.tab.c: No such file or directory
gcc: fatal error: no input files
Fix this by forcing usage of bison under STAGING_DIR_HOST/bin via YACC
make variable.
Cc: Thomas Albers <thomas.gameiro@gmail.com>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Cc: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Ivan Revyakin <LovingFox@GMail.com>
Tested-by: Thomas Albers <thomas.gameiro@googlemail.com>
Ref: https://forum.openwrt.org/t/bpi-r64-kernel-4-19-kernel-menuconfig-error
Fixes: 965f341aa9 ("build: fix host menu config targets using ncurses")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Replace 2 instances of non posix use of 'head' with posix compliant
'cut'.
'head -c n' cuts 'n' bytes from the passed string and happens to work on
Linux & Mac OS X even though '-c' is not posix.
'head --bytes n' does the same thing and happens to work on linux but
not on Mac OS X and is also not posix.
'cut -b1-8' cuts the first 8 bytes from the passed string and is posix
compliant, hence works on Linux & Mac OS X.
Our usage of 'head --bytes' was particularly unfortunate since it was
used to calculated the RootFS UUID passed to grub - the net result being
a non-functioning system waiting for the root file system to appear.
Thanks to karlp, ynezz & others for pointers on solving this.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
x86, mvebu and tegra targets are currently using more or less same
SIGNATURE variable which provides unique partition ID/signature, so it
makes sense to refactor it out into common variable which could be
reused by all targets. While at it, make the content of the variable
reproducible.
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2019-March/016148.html
Signed-off-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
[renamed to IMG_PARTSIGNATURE, reworked with epoch+vermagic hash]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit 881ed09ee6 ("build: create JSON files containing image info")
has removed the crucial empty new line from the image copy step
resulting in the following errors during make function expansion:
GZ_SUFFIX :=
bash: GZ_SUFFIX: command not found
Makefile:86: recipe for target 'openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin' failed
Fixes: 881ed09ee6 ("build: create JSON files containing image info")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
UUID of ext4 volumes generated by make_ext4fs are determined by volume
label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label
is empty
Labeling them does not make them unique but tools like block command
from fstools have a better chance differentiating them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
It's related to the upstream kernel commit adf82accc5f5 ("netfilter:
x_tables: merge ip and ipv6 masquerade modules").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The luci and freifunk feed having a common Makefile included by the
individual packages. Currently a change to this file will be ignored
when running "scripts/feeds update".
When we are updating for a feed, add a dependency for all .mk files
in the root of it.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
This separates the options for signature creation and verification
* SIGNED_PACKAGES create Packages.sig
* SIGNED_IMAGES add ucert signature to created images
* CHECK_SIGNATURE add verification capabilities to images
* INSTALL_LOCAL_KEY add local key-build to /etc/opkg/keys
Right now the buildbot.git contains some hacks to create images that
have signature verification capabilities while not storing private keys
on buildbot slaves. This commit allows to disable these steps for the
buildbots and only perform signing on the master.
Signed-off-by: Paul Spooren <mail@aparcar.org>
'append-uImage-fakehdr' can now accept magic number as a second, optional
parameter (passed directly to 'mkimage' command with '-M' option). This
enables construction of proper Netgear-specific fake rootfs images
(required for flashing WNDR4300 for example).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Problem found on alpine linux when trying to `./scripts/feeds update -a`,
which results in `Build dependency: Missing seq command`.
Ref: https://github.com/openwrt/openwrt/pull/1926
Suggested-by: imShara <shara@protonmail.com>
[reworded commit and turned faulty Sob into Suggested-by]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some kmods (gpio-hotplug, wireguard) store the build path in the
compiled files and therefore make it harder to rebuild the official
binaries. As the same "iremap" function is used as for other binaries,
the change is compatible with gcc7 and 8.
Tested with both gcc7 and gcc8 resulting in build path independent
reproducible builds.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This is a follow up of 8cb13f4e6d which sets the right timestamp for the
/init file in initramfs. The previous patch doesn't cover it as the
files appear to come from a later step during compilation.
CC: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Paul Spooren <mail@aparcar.org>
The check for libelf in the kernel build is not enough, because the code that
uses libelf for stack validation is completely non-portable, as it tries to
include asm/types.h and relies on kernel types in user space.
Until this is fixed properly, the only solution is to disable this on any non
Linux build host
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The JSON info files contain details about the created firmware images
per device and are stored next to the created images.
The JSON files are stored as "$(IMAGE_PREFIX).json" and contain some
device/image meta data as well as a list of created firmware images.
An example of openwrt-ramips-rt305x-aztech_hw550-3g.json
{
"id": "aztech_hw550-3g",
"image_prefix": "openwrt-ramips-rt305x-aztech_hw550-3g",
"images": [
{
"name": "openwrt-ramips-rt305x-aztech_hw550-3g-squashfs-sysupgrade.bin",
"sha256": "db2b34b0ec4a83d9bf612cf66fab0dc3722b191cb9bedf111e5627a4298baf20",
"type": "sysupgrade"
}
],
"metadata_version": 1,
"supported_devices": [
"aztech,hw550-3g",
"hw550-3g"
],
"target": "ramips/rt305x",
"titles": [
{
"model": "HW550-3G",
"vendor": "Aztech"
},
{
"model": "ALL0239-3G",
"vendor": "Allnet"
}
],
"version_commit": "r10920+123-0cc87b3bac",
"version_number": "SNAPSHOT"
}
Signed-off-by: Paul Spooren <mail@aparcar.org>
On a recent Gentoo Linux installation, invoking `make menuconfig`, `make
kernel_menuconfig` or `make kernel_nconfig` in the build system fails,
whereas for example `make menuconfig` in the kernel tree alone works as
expected.
This is happening because STAGING_PREFIX is not defined when kernel's
{menu,n}config target calls pkg-config from the toolchain/host and thus
pkg-config returns an empty value, and the fallback values in the kernel
config script are applied but those are off and the linking fails.
Solution is to use system's pkg-config for all ncurses based menu config
targets in order to provide proper compiler/linker flags.
Ref: FS#2423
Cc: Thomas Albers <thomas.gameiro@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some tools doesn't support SOURCE_DATE_EPOCH (e.g. initramfs images).
Ensure all files of a root filesystem are set to SOURCE_DATE_EPOCH.
Make initramfs builds reproducible (for ramips).
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently for at91 target, Build/install-dtb can be triggered concurrently for
multiple different TARGET_FILESYSTEMS, cp command can fail when the
target file is already open exclusively by other cp process
[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ubifs+fs=-m_2048_-e_126KiB_-c_2048+pkg=68b329da ]
[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ext4+pkg=68b329da ]
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp: cannot create regular file '/builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb': File exists
Makefile:87: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb' failed
make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb] Error 1
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This reverts commit 1c0290c5cc.
Dropping the nopad can make the padding overflow into the next erase
block on devices using a non-aligned rootfs start. This breaks the jffs2
overlay partition with the following messages:
[ 30.343877] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 30.376512] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[ 30.385253] jffs2: empty_blocks 196, bad_blocks 0, c->nr_blocks 197
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Pass suitable pkg-config overrides to the kernel build process in
order to let our pkg-config wrapper discover libraries provided
by tools/.
This mainly affects the use of libelf which is required for the
CONFIG_STACK_VALIDATION features. So far, the build system either
silently used host system libraries or kbuild simply disabled the
feature due to the lack of a suitable libelf.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While the -nopad option prevents mksquashfs from padding the
image to an arbitrary 4k. It does not take into consideration
that squashfs is programmed to have this 4k padding when it's
being used on on a block device... which is its main "use-case".
Now, after a week long discussion on the ML that included a
back-and-forth between some of the possible options.
But this is likely the best KISS patch to deal with the issue
right away given the limited resources.
From squashfs code point of view, be warned. The 4k padding is
not enough when dealing with devices that have a PAGE_SIZE
bigger than 4k.
if it turns out to be affecting you, then please look-up either:
"FS#2460 - kernel panic reading squashfs from ubi volume" bug
Or the discussion on the OpenWrt-Devel ML in
"amp821xx: use newly added pad-squashfs for Meraki MR24" and
"Squashfs breakage lottery with UBI..."
before making an educated guess.
Note: This will not affect the "tiny"/small flash devices as
much as it seems at first. This is because the the rootfs_data
partition that follows uses jffs2. And it requires to be aligned
to the flash block-size in order to work at all.
So either the involved FSes will meet in the middle as before,
or not at all. But in that latter case the image was already
hoping for the "undefined behaviour" gamble to turn out in its
favour and this is probably why this was unnoticed for so long.
Fixes: FS#2460
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Underscores don't harm in filenames, however the sanitize function from
version.mk replaces them, causing inconsistent filenames.
A fix tried to solve this previously via
dfe99645db however I did not look close
enough:
openwrt-ath79-generic-8dev-carambola2.manifest # current
openwrt-ath79-generic_8dev-carambola2.manifest # patched
---------------------^
Eventually the sanitization of PROFILES *could* be removed as more and
more profiles follow the device tree approach of vendor_model, neither
containing upper case letters nor spaces.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Some devices are produced and sold under different names. To debloat
the buildroot but keeping it complete, new variables are introduced to
handle different namings. Below an example taken from a recent PR[0]
DEVICE_VENDOR := Arcadyan
DEVICE_MODEL := ARV4520PW
DEVICE_ALT0_VENDOR := Vodafone
DEVICE_ALT0_MODEL := Easybox 800
DEVICE_ALT1_VENDOR := Airties
DEVICE_ALT1_MODEL := WAV-281
With this commit the buildroot is extended to take care of up to three
alternative namings. The primary title plus alternatives names (if
defined) are shown in the `make menuconfig` dialog. Selecting on of
devices automatically selects all alternative names as they share the
same profile.
A list of the newly introduced variables:
DEVICE_ALT0_VENDOR :=
DEVICE_ALT0_MODEL :=
DEVICE_ALT0_VARIANT :=
DEVICE_ALT1_VENDOR :=
DEVICE_ALT1_MODEL :=
DEVICE_ALT1_VARIANT :=
DEVICE_ALT2_VENDOR :=
DEVICE_ALT2_MODEL :=
DEVICE_ALT2_VARIANT :=
[0]: https://github.com/openwrt/openwrt/pull/2229/files#diff-b436f01932a18876c27800ba183d95f6R140
Signed-off-by: Paul Spooren <mail@aparcar.org>
The LEDE URL is automatically redirected to the OpenWRT one,
returning an HTTP 301 code (Moved Permanently).
Also, use https, as indicated by the redirect.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Allow overriding the default selection state for Devices, similar to
setting a default for packages.
E.g. by setting DEFAULT to n, they won't be selected by default anymore
when enabling all device in the multi device profile.
This allows preventing images being built by the default config for
known broken devices, devices without enough RAM/flash, or devices not
working with a certain kernel versions.
This does not prevent the devices from being manually selected or images
being built by the ImageBuilder. These devices often still have worth
with a reduced package-set, or as a device for regression testing, when
no better device is available.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The manifest file is based on IMG_PREFIX and PROFILE_SANITIZED, whereas
the latter takes a string like DEVICE_8dev_carambola2 and sanitizes it.
This behaviour results in a useless "device_" profile-prefix in the
device manifest filename. Now uses *subst* to remove that.
Therefore this patch results more consistent device file names:
openwrt-ath79-generic-8dev_carambola2-initramfs-kernel.bin
openwrt-ath79-generic-8dev-carambola2.manifest
openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin
instead of a single file being called
openwrt-ath79-generic-device_8dev-carambola2.manifest
Signed-off-by: Paul Spooren <mail@aparcar.org>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Github releases usually don't contain the project name in the release
filename, which makes them very inconvenient to use from the build
system. Add support for naming the local file differently.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
I'm trying to create a package for libgpiod, which uses
AC_CONFIG_AUX_DIR macro, which is probably leading to the following
configure error:
autoreconf: running: /openwrt.git/staging_dir/host/bin/libtoolize --force
OpenWrt-libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `autostuff'.
OpenWrt-libtoolize: linking file `autostuff/ltmain.sh'
OpenWrt-libtoolize: putting macros in `m4'.
...
configure: error: cannot find install-sh, install.sh, or shtool in autostuff "."/autostuff
>From the build output it's clear, that libtoolize isn't installing
install-sh symlink, because libtoolize would install install-sh only if
it's being run with --install parameter. Corresponding part in
libtoolize:
if $opt_install; then
func_config_update config.guess \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_config_update config.sub \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_install_update install-sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
fi
func_ltmain_update ltmain.sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
Adding --install parameter to libtoolize fixes this build issue:
autoreconf: running: /openwrt.git/staging_dir/host/bin/libtoolize --install --force
OpenWrt-libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `autostuff'.
OpenWrt-libtoolize: linking file `autostuff/config.guess'
OpenWrt-libtoolize: linking file `autostuff/config.sub'
OpenWrt-libtoolize: linking file `autostuff/install-sh'
OpenWrt-libtoolize: linking file `autostuff/ltmain.sh'
OpenWrt-libtoolize: putting macros in `m4'.
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When bumping buildroot to Python 3, we need to assure, that Python
symlink in staging bin directory points to Python >= 3.5 as well.
We can't rely completly just on SetupHostCommand as its executed only in
cases when the $(STAGING_DIR_HOST)/bin/python doesn't already exist, so
we need to remove it before running SetupHostCommand.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch switches Python used in buildroot to Python 3 as Python 2.x
series is going to be EOL relatively soon[1].
"Being the last of the Python 2.x series, 2.7 will have an extended
period of maintenance. Specifically, 2.7 will receive bugfix support
until January 1, 2020. After the last release, 2.7 will receive no
support."
It seems like Python 3 is going to be needed in order to support Meson
build system which has gained some traction recently.
Build tested on following targets:
ath79/generic
imx6/generic
ipq40xx/generic
lantiq/xway
layerscape/armv7 (broken)
layerscape/armv8_32b (broken)
layerscape/armv8_64b (broken)
mvebu/cortexa72
ramips/mt7621
ramips/mt7620
sunxi/cortexa7
x86/64
Layerscape targets are unfortunately left broken as their ls-rcw
firmware package uses Python 2 and converting it to Python 3 would take
more then reasoanble amount of time (I've tried to fix it already) and
would be better fixed by someone who can even run test it.
Run tested on ath79 (Archer C7 v5), ipq40xx (nbg6617) and x86_64 (QEMU
and apu2).
1. https://www.python.org/dev/peps/pep-0373/
Ref: PR#1937
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Mathew McBride <matt@traverse.com.au>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This feature is similar to the SRC_TREE_OVERRIDE. However instead of having
to manually create a symlink inside the package folder, the buildsystem
will check if $(TOP_DIR)/src-checkout/$(PKG_NAME)/.git is present and use
this instead.
Signed-off-by: John Crispin <john@phrozen.org>
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since we switched to 4.19, the kernel build checks for libelf to decide if
it should build tools for stack validation.
On macOS, this check fails during target/compile, but succeeds during package
build (because of the pkg-config path picking up target libraries).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Image padding with dd needs to be done in an OS independent way as not
all dd understand capital letter unit specifiers, and not all understand
lowercase either.
Fixes: 97833a57ef ("build: image: add pad-to and pad-rootfs-squashfs helpers")
Reported-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This common code could be shared by at least 3 targets (malta, armvirt
and x86) so let's factor it out to separate variable.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Declaring a package without the appropriate install section is an easy
mistake to make, especially when renaming packages. Since this is also
easy to detect, warn about it when it happens.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
No-objections-at-all-by: Jo-Philipp Wich <jo@mein.io>
Recent kernel versions need toolchain in order to properly configure
kernel, for example to set CC_HAS_ASM_GOTO config symbol, so missing
toolchain leads to the following error while running `make
kernel_oldconfig` on ath79 target with 4.19 kernel in the clean tree:
init/Kconfig:17: syntax error
init/Kconfig:16: invalid option
./scripts/clang-version.sh: line 15: mips-openwrt-linux-musl-gcc: command not found
./scripts/gcc-plugin.sh: line 11: mips-openwrt-linux-musl-gcc: command not found
net/sched/Kconfig:44: warning: menuconfig statement without prompt
make[4]: *** [scripts/kconfig/Makefile:69: oldconfig] Error 1
So in order to support this new kernel versions, this patch adds
toolchain as a hard dependency to the kernel_*config targets.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Extend the packageauxvars database to keep a list of possible package
dependencies for each provider, then utilize this information in buildroot
to resolve the ABI version dependencies of dependent packages up to five
levels deep.
This should properly trigger rebuilds for packages indirectly depending
on other packages whose ABI_VERSION changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Also fix a malformed patch issue caught during refresh.
It was caused by removing a whitespace without altering
the index values in a patch which alters a patch.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Fixes: cf65262492 ("kernel: bump 4.19 to 4.19.51")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
- 220-optimize_inlining.patch
- 640-netfilter-nf_flow_table-add-hardware-offload-support.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refreshed all patches.
Altered patches:
- 220-optimize_inlining.patch
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Sungbo Eo
Jeff Kletsky
Xu Wang
Jo-Philipp Wich
Hauke Mehrtens
David Bauer
Adrian Schmutzler
Koen Vandeputte
Rosen Penev
Petr Štetiar
Kamil Wcislo
Thomas Weißschuh
Kevin Darbyshire-Bryant
Paul Spooren
Yousong Zhou
Rafał Miłecki
Sven Roederer
John Crispin
Andre Heider
Michal Cieslakiewicz
Felix Fietkau
Alexander Couzens
Jonas Gorski
Christian Lamparter
Luis Araneda
Jeffery To