Commit Graph

926 Commits (16222a10108c10115cde6b8ef96eabba8fb8b84b)

Author SHA1 Message Date
Mathias Kresin 3dc757856c lantiq: fix typo in EASY80920.dtsi
There is no device tree property named phynmode0. Use phy-mode as it is
done for the other ethernet nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:18:14 +02:00
Thomas Nixon 50e3659703 lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:

    CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
    RAM: 64MiB
    Flash: 8MiB
    Ethernet: 1x100M
    DSL: VDSL2+, ADSL2+
    reset button, 3x bi-color LEDs

Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.

To upgrade from the vendor firmware, upload factory.img

The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.

Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.

Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2017-07-07 07:13:24 +02:00
Mathias Kresin 08c499f865 lantiq: use img file extension for DGN3500 factory images
The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:01 +02:00
Piotr Dymacz 5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Stijn Tintel 880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Koen Vandeputte 69649a1b45 kernel: update kernel 4.9 to 4.9.34
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)

Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 07:21:03 +02:00
Mathias Kresin 8e0d7d6574 build: move lzma2eva build step to image-commands.mk
Move it to image-commands.mk so that it can used by other targets with
eva based boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin d165f1f3bc kernel: move Lantiq PEF7061/7071/7072 phy driver to generic
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.

The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin 259fc1e778 lantiq: show xdsl line init status on shared dsl/internet led
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.

Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:38:18 +02:00
Martin Schiller 03776d813c lantiq: restore netdev trigger of dsl led on line up
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:34:16 +02:00
Sergey Ryazanov 68e7a2a0b7 kernel: disable CONFIG_SG_POOL by default
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Tino Reichardt e097eb27af lantiq: fix 0008-MIPS-lantiq-backport-old-timer-code.patch for Amazon-SE
The patch 0008 removes the vanilla kernel gptu.c of lantiq.
But the replacement file timer.c does not work Amazon-SE and
is also protected therefore with an CONFIG_SOC_AMAZON_SE :-)

This commit will re-activate the default vanilla kernel code
in gptu.c for Amazon-SE.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[refresh patches and add same change for kernel 4.9]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-06-03 21:35:53 +02:00
Tino Reichardt 712ebe95f8 lantiq: add Allnet ALL0333CJ support
This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.

Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)

Installation:
- can be done via telnet+tftp or serial console
- default passwords:
  - via telnet (root:admin)
  - via webinterface http://172.16.1.254:8235/ (admin:coolwhite)

Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0

Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset

Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt 995ad357f9 lantiq: enable Netgear DGN1000B image build
Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.

This is just the proper way, so that developing on this
device is known to be done in the near future.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt 9b321bc60d lantiq: add Amazon-SE subtarget
Re-Add support for the Amazon-SE subtarget on Lantiq.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt 1039e41dea lantiq: fix amazonse.dsti
Add missing memory@0 and localbus@0 sections.
Fix MEI and GPTU interrupt definitions.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Helge Mader 63a20c95fd lantiq: modified lantiq_dsl.sh status output of latency
Signed-off-by: Helge Mader <ma@dev.tdt.de>
2017-06-02 22:49:45 +02:00
Helge Mader 666dd85b36 lantiq: fix lantiq_dsl.sh status and lucistat output
Signed-off-by: Helge Mader <ma@dev.tdt.de>
2017-06-02 22:49:33 +02:00
Martin Schiller 82f7fd7457 lantiq: pinctrl: xway: fix copy/paste error in xrx200_grps
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2017-05-29 09:51:19 +02:00
Hauke Mehrtens 0b17375931 kernel: update kernel 4.9 to 4.9.30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-27 00:48:37 +02:00
Mathias Kresin 822ee54544 treewide: fix device tree path in scripts
The device tree is at /proc/device-tree/ without a base subdir.

Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 15:18:30 +02:00
Mathias Kresin da472e5b30 treewide: access device tree from userspace via /proc/
Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Hauke Mehrtens 6153248052 lantiq: spi: double time out tolerance
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:

m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e

After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:51:28 +02:00
Koen Vandeputte e842e16f45 kernel: update kernel 4.9 to 4.9.29
- Refresh all patches
- Removed upstreamed
- Adapted 1

Compile tested on: bcm53xx, cns3xxx, imx6, lantiq
Run tested on: cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[update from 4.9.28 to 4.9.29]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:51:22 +02:00
Kevin Darbyshire-Bryant 088e28772c kernel: update kernel 4.4 to version 4.4.69
Refresh patches. A number of patches have landed upstream & hence are no
longer required locally:

062-[1-6]-MIPS-* series
042-0004-mtd-bcm47xxpart-fix-parsing-first-block

Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup
as it was incorrectly included upstream thus dropped from LEDE.
As it has now been reverted upstream it needs to be included again for
LEDE.

Run tested ar71xx Archer C7 v2 and lantiq.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[update from 4.4.68 to 4.4.69]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:48:16 +02:00
Mathias Kresin 92a12c434c lantiq: fix avm fritz box mac addresses
It has been shown that the Fritz boxes have the correct mac address set
in the wireless calibration data/eeeprom. Use this mac address as base
for the ethernet and xdsl interface increment/decrement the address to
match the values stored in the tffs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-05 19:58:49 +02:00
Kevin Darbyshire-Bryant 42120bd7f3 lantiq: DGN3500: make switch LEDs blink on activity
Make switch port LEDs blink on activity as they do with stock firmware.

The u-boot loader sets suitable values in the LED control register that
unfortunately get blown away by the linux switch driver init.  Restore
that value by using driver 'initvals'.  0x0431 is the led control
register, the value 0x0960. Each nybble represents each LED's mode
(LED3,2,1,0) in this case OFF, 1000LINK+Activity, 100/10LINK+Activity,
OFF.  Only LED1&2 are physically present.

Enabling the blinkenlights exposed the fact that an RRCP packet was
being emitted by the switch on all ports every second.  Further initvals
copied from stock firmware's u-boot driver disabled this 'feature'.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-04-25 19:29:59 +02:00
Kevin Darbyshire-Bryant e1d433b293 lantiq: improve DGN3500 LED definitions
Add red:internet led on gpio 30 previously claimed as missing.
Wifi led was claimed as blue however there are no blue leds on the
board at all.  Actually there are two wifi leds, green & amber so add
definitions for those.  Make the newly discovered green wifi led gpio
14 the default.

There is no amber power led on this board. The mention of the amber
power led in the manual means power red and power green at the same
time.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[removed unnecessary aliases, add migration script]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:50:55 +02:00
Jo-Philipp Wich aefa195749 kernel: update kernel 4.4 to 4.4.61
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-15 18:26:41 +02:00
Mathias Kresin af9afa2811 lantiq: drop tffs patches
With the fritz-tools a userspace parser for the Tiny Flash File System
is available and makes the tffs2 kernel patches obsolete.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Mathias Kresin 136718a3d9 kernel: update MIPS pci fix to the accepted version
Fix the list order instead of adjusting the controller scan order.
Revert the former required changes to the lantiq PCIe driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Hauke Mehrtens 6c1657623f lantiq: update spi driver to upstream version
These patches are backported from upstream Linux kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 15:58:17 +02:00
Hauke Mehrtens fb7ea71c15 kernel: update kernel 4.9 to 4.9.17
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:19 +02:00
Stefan Koch 322a7226d3 lantiq: vr9 fxs support: remove unused wdog declarations and initializers
modify 0152-lantiq-VPE.patch from
commit e0229a16b0 ("lantiq: added support for VPE1")

- remove wdog function declarations from header (asm/vpe.h)
- remove wdog command line init functions (vpe.c)

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-24 08:09:39 +01:00
Stefan Koch c9783dd728 lantiq: vr9 fxs support: remove soft-watchdog functionality
- remove patched header (vpe.h) because kernel
  already provides one (asm/vpe.h)
- remove module softdog_vpe since watchdog functionality is unused
- remove module softdog_vpe from Makefile

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-24 08:09:39 +01:00
Mathias Kresin e4c53c751e lantiq: fix pci with kernel 4.9
Commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed
the controller list from reverse to straight order. Use the last entry
in the controller list to get the fist conroller of the system.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Felix Fietkau fd93f81fd8 lantiq: remove lantiq_board_model, it is unused
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Felix Fietkau 7e798dab56 lantiq: remove lantiq_board_name, use the generic function instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:21 +01:00
Felix Fietkau aa95d6cd20 lantiq: move lantiq_board_detect() to 03_preinit_board.sh
It is only used there

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:21 +01:00
Oswald Buddenhagen 6a82f4006c lantiq: Shortcut non-pppoa interfaces in dsl_notify
No need to query 'up' and 'auto' when they are not going to be used.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
2017-03-17 08:58:50 +01:00
Stefan Koch 443e67a459 lantiq: vr9 fxs support: fixed check of SMP state within vpe-mt.c
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option

The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.

This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.

Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.

Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.

In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-17 08:58:50 +01:00
Stefan Koch d4203dfa55 lantiq: vr9 fxs support: fixed check of SMP state within vpe-mt.c
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option

The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.

This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.

Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.

Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.

In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-13 14:20:47 +01:00
Hauke Mehrtens 31c6452107 kernel: update kernel 4.4 to 4.4.53
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:46:02 +01:00
Hauke Mehrtens 9a065fcfec kernel: update kernel 4.9 to 4.9.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:45:50 +01:00
Mathias Kresin 73eb5c74a1 lantiq: use the P2812HNUF* wan port as wan
The port is labeled as wan and was only used as lan port because of the
"tx ring full" issues fixed with 8f02f7c.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:06 +01:00
Mathias Kresin cd8b20931e lantiq: xrx200: use vlan for ethernet wan port
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.

The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.

If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.

Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:00 +01:00
Mathias Kresin 715b066419 lantiq: fix broadcasts and vlans in two iface mode
The two phy operation mode where one phy is assigned to an interface
without lantiq,* device tree property and the other phy is assigned to
an interface with the lantiq,wan device property was broken with the
multicast package leaks between vlans fixes.

Move the multicast packages relevant portmap settings to the condition
which handles multicast packages for better readability.

Replace the priv->port_map based port_map only for the interface which
has the lantiq,switch device tree property set, to allow tagged
multicast packages in two phy mode where the lantiq,switch device tree
property isn't used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:00 +01:00
Alex Maclean 6254a2028c lantiq: add support for the Alpha ASL56026
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.

CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04

UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX

Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.

The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)

To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:

	VR9 # setenv loadaddr 0xB0040000
	VR9 # setenv f_upgrade_addr 0xB0040000
	VR9 # setenv f_upgrade2_addr 0xB0040000
	VR9 # saveenv

Then flash the firmware image:

	VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
	VR9 # erase B0040000 +${filesize}
	VR9 # cp.b 0x81000000 0xB0040000 ${filesize}

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-03-08 19:06:04 +01:00
Alex Maclean a9b74f9f81 lantiq: clarify VG3503J name
Append the ECI model to the device name, to avoid confusion with the
older model.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-03-08 19:06:04 +01:00
Felix Fietkau 891ed144ff lantiq: select kmod-mt7603 instead of kmod-mt76 for WBMR-300HPD
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-27 14:20:14 +01:00