Commit Graph

1502 Commits (1191eeff8ec86850a5a952987816823359f37793)

Author SHA1 Message Date
John Crispin acbed0eff3 ramips: mt7621: undo mips-cm probe hack to not wipe out memory regions
Since now we hopefully setup memory regions properly we no longer need this hack.

Tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47905
2015-12-17 09:26:43 +00:00
John Crispin 622e268710 ramips: mt7621: setup memory region for pcie controller memory
Only compile tested since I do not have any hardware with
devices on pcie bus.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47904
2015-12-17 09:26:35 +00:00
John Crispin e8890c6be0 ramips: mt7621: add patch to setup CM memory region for palmbus
This is tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47903
2015-12-17 09:26:28 +00:00
John Crispin b4bb10b3a0 ralink: update config files to build the cleaned up ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47902
2015-12-17 09:26:20 +00:00
John Crispin 402db12f1a ralink: drop dummy profile from mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47901
2015-12-17 09:26:09 +00:00
John Crispin 651e620de5 ralink: fixup devicetree files to work with new ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47900
2015-12-17 09:25:57 +00:00
John Crispin fa854a02a1 ralink: drop old ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47899
2015-12-17 09:25:30 +00:00
John Crispin 31116661ff ralink: add reworked ethernet driver
update to the version of the driver that is on its way upstream

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47898
2015-12-17 09:25:24 +00:00
John Crispin 5d4f5689fd ramips: add missing kernel symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47884
2015-12-12 21:01:02 +00:00
John Crispin 4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin 1c6c9549d6 ramips: add support for Spansion S34ML0[24]G2 flash
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47880
2015-12-12 07:37:53 +00:00
John Crispin 9e5044926b ralink: remove stray "+" from ethernet driver
this is what you get if you manually apply patches with c&p

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47877
2015-12-12 06:42:17 +00:00
John Crispin 8470e30a76 ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47876
2015-12-12 06:42:11 +00:00
John Crispin e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau 77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
Jo-Philipp Wich 67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin 9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin 6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
John Crispin abd11be13c ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47843
2015-12-11 15:03:39 +00:00
John Crispin a87272ebfb ramips: enable CPS for mt7621
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.

This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47842
2015-12-11 15:03:27 +00:00
John Crispin fbc1624d6a ramips: irq handlers do not get irq in 4.3 kernel, update patches
This resolves compilation warnings like this:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe':
drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types]
   irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler);

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47841
2015-12-11 15:03:16 +00:00
John Crispin 4076d12f41 ramips: Fix CM_GCR_CPC_BASE_CPCBASE_{MSK, SHF} values
Update CM_GCR_CPC_BASE_CPCBASE_{MSK,SHF} to match datasheet

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47840
2015-12-11 15:03:08 +00:00
John Crispin e4ee2402cb ramips: fold gic patch into mt7621 support patch
All gic patch was doing is removing code added by mt7621 support patch.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47839
2015-12-11 15:02:55 +00:00
John Crispin ed8775d3c3 ramips: backport series of patches that ensure GCRs of other CPUs are accessed properly
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47838
2015-12-11 15:02:50 +00:00
John Crispin e0d77e68ce ramips: backport batch fixing illegal instruction when booting secodnary CPUs in CPS mode
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47837
2015-12-11 15:02:36 +00:00
John Crispin 81c999bbda ramips: mt7621: use symbolic names of gic interrupt settings
This also adds dts nodes for cpc and mc for documentation purposes

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47836
2015-12-11 15:02:13 +00:00
John Crispin 6df4426245 ralink: bump to the target to v4.3
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47831
2015-12-10 19:06:32 +00:00
Felix Fietkau 09335a0a2f build: fix arch used during dts compilation
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47823
2015-12-10 12:39:32 +00:00
Jo-Philipp Wich 527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich 8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich 9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich de51026515 ramips: switch ucidef_add_switch_vlan() to ucidef_add_switch_ports()
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47717
2015-12-03 15:46:29 +00:00
John Crispin 06af966094 ramips: remove duplicate patch
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47670
2015-11-28 23:26:03 +00:00
John Crispin 82557aee85 ramips: adapt VoCore to new second spi device code
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47667
2015-11-28 23:24:52 +00:00
John Crispin af14fa011c ramips: add second SPI clocks
These clocks were missing in the changes introduced in r47573-47580

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47666
2015-11-28 23:24:40 +00:00
Jo-Philipp Wich ecf5b4fab7 ramips: hg255d: replace ucidef_set_led_interface() with ucidef_set_led_netdev()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47657
2015-11-26 12:46:04 +00:00
John Crispin 7b4acdeff6 ralink: renable nand support
CONFIG_MTK_MTD_NAND was incorrectly disabled by r47619.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47640
2015-11-24 22:00:55 +00:00
Felix Fietkau d8a62fdbc2 ramips: fix typo in image makefile (#18712)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47627
2015-11-24 19:29:56 +00:00
John Crispin 8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin 12b6f4cf71 ramips: add second spi master sysclk
for mt7620, rt3883 and rt5350

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47616
2015-11-24 18:28:54 +00:00
John Crispin c550ad3d3a ramips: update dtsi files to support second spi device
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47580
2015-11-22 11:49:13 +00:00
John Crispin a941b34008 ramips: use transfer_one instead of transfer_one_message on rt2880 spi
* use kernel buildin transfer_one_message. we only need to implement
transfer_one and set_cs function
* should support use gpio as cs pin
* deselected the spi device when setup and add debug info
* only reset device when first driver probe

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47579
2015-11-22 11:49:04 +00:00
John Crispin 95aa28da81 ramips: move rt2880 spi clock and reset init code to spi_prepare_message
before spi transfer. use spi_prepare_message to setup spi hardware. it
will setup MSB, spi mode and speed
remove sys_freq member and speed check code

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47578
2015-11-22 11:48:57 +00:00
John Crispin a58dec6275 ramips: improve rt2880 spi setup
* check clock rate, SPI mode, and word sizes
* setup spi polarity
* enable spi1 hw if need

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47577
2015-11-22 11:48:51 +00:00
John Crispin 2ce886f149 ramips: clean up rt2880 spi probe/remove
* fill struct according to the member order
* add error clean up
* set min/max spi speed. so we don't need to check again

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47576
2015-11-22 11:48:45 +00:00
John Crispin bf89d139e1 ramips: improve rt2880 spi wait ready function
use loops_per_jiffy, spi clock speed and write bytes to get the
spi loop count. if loop to 0 than spi operation timeout.
remove usleep. we only write 1 byte to spi device. use busy loop
would be better.

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47575
2015-11-22 11:48:34 +00:00
John Crispin 702c480dfe ramips: remove rt2880 spi lock and clean bit operation
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47574
2015-11-22 11:48:21 +00:00
John Crispin 13fbd6fea7 ramips: add rt2880/mt7620 spi register defines
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47573
2015-11-22 11:48:10 +00:00
John Crispin 55ee2e0ef7 ralink: add missing nand layer hack
It turned out that mtk_nand driver uses some sophisticated accounting and a
general nand code must be patched.

This patch adds required read and erase calls to a general nand code. I
used a  code  for re6500 released by Linksys as a reference.

All required operations (erase, write and read) are usable. However I found
that jffs2 filesystem can be created only on top of a ubi volume. I tried
to create jffs2 directly on mtd device but pages with clean markers are
became uncorrectable.

Signed-off-by: Kirill Berezin <fyiwdt@gmail.com>

SVN-Revision: 47565
2015-11-21 21:25:33 +00:00
John Crispin 40ddc71cc9 ramips: init usb power for Lenovo Y1S
Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47557
2015-11-21 21:24:38 +00:00
Felix Fietkau b95aed986a ramips: minor fixes for mt7621 profiles
* remove references to non-existing kmod-usb3-mt7621
 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47407
2015-11-07 12:51:48 +00:00
John Crispin aebf73f045 ramips: fix previous commit
r47388 accidentially changed 2 files too many

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47389
2015-11-05 10:03:58 +00:00
John Crispin dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
John Crispin 2350c149b5 ramips: add feature to blink led on sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47373
2015-11-03 13:32:02 +00:00
John Crispin 165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin 0f4b153e3d ramips: add eeprom mtd partition to the Asus RP-N53 dts
This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47350
2015-11-02 10:18:09 +00:00
John Crispin 907c67fa87 ramips: preinit: use iproute2 instead of vconfig
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips

The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47349
2015-11-02 10:18:02 +00:00
John Crispin 3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin 83693c911a ramips: add function to change rt2x00 wifi eeprom mac
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47347
2015-11-02 10:17:41 +00:00
John Crispin a76de8e7b3 ramips: mt7620 add icplus phy driver kernel config symbol
Add missing icplus phy driver kernel config symbol to mt7620 subtarget.
This is needed since some mt7620 devices have icplus ip1001 ethernet transceiver

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47346
2015-11-02 10:17:35 +00:00
John Crispin 8fa6927415 ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47345
2015-11-02 10:17:26 +00:00
John Crispin ed30ca8e39 ramips: rt305x: enable seama mtdsplit parser
D-Link DIR-610 A1 needs seama mtdsplit parser.
This patch should fix #18046.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 47341
2015-11-02 10:16:56 +00:00
John Crispin 6dcbf74a94 ramips: rt305x: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 47340
2015-11-02 10:16:48 +00:00
Hauke Mehrtens 55a912f43e kernel: update kernel 3.18 to version 3.18.23
Changelog:
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.22
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.23

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47334
2015-11-01 13:45:57 +00:00
Felix Fietkau b100027a83 ramips: fix for kernel 4.0 napi repoll need return budgets number
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47306
2015-10-30 22:32:49 +00:00
John Crispin 228eeb647e ramips: make the alsa driver register the codec
this allows using the codec even if it is not listed in the DTS

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47256
2015-10-26 09:00:42 +00:00
John Crispin e043ada1d5 ramips: gpio-mt7621 was not handling irqs above 31 properly
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47238
2015-10-20 07:09:20 +00:00
John Crispin 7295e9fb8b ramips: add alsa support
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47205
2015-10-19 10:07:54 +00:00
John Crispin f5d5cb0114 ramips: add a baurate hack
When talking to an atmel controller we need 9600 or 250000 baud.
as 250000 does not exist we use 2500000.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47204
2015-10-19 10:07:43 +00:00
John Crispin 51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin b0f7e6bc83 ramips: fix /target/linux/ramips/dts/HC5XXX.dtsi
dtb complained about those lines

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47151
2015-10-07 08:00:40 +00:00
Felix Fietkau 2686dc6dd8 ramips: enable mt76 by default for the mt7620 subtarget (for devices with mt7620 + mt7612)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47146
2015-10-06 12:32:31 +00:00
Felix Fietkau 38389c79c2 ramips: improve read performance of the m25p80 chunked io patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47137
2015-10-05 11:34:16 +00:00
John Crispin b4db6d29d3 ramips: improve systick timer
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.

Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47122
2015-10-05 10:27:09 +00:00
John Crispin 10f75a2b7f ramips: fix use remove_irq to release irqaction resource
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47121
2015-10-05 10:27:04 +00:00
John Crispin ccf89e71f2 ramips: add support for 16MB VoCore
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47120
2015-10-05 10:27:00 +00:00
John Crispin 948e67cb16 ramips: fix size-cells for spi nodes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47119
2015-10-05 10:26:54 +00:00
John Crispin d4cd8f89eb ramips: Ralink RT3883 RGMII pinmux fix.
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.

Signed-off-by: Nick Leiten <nickleiten@gmail.com>

SVN-Revision: 47118
2015-10-05 10:26:40 +00:00
John Crispin aecac14cc4 ramips: Enable rx of 1536 bytes ethernet frames on MT7621
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47117
2015-10-05 10:26:34 +00:00
John Crispin 7b306e3eb3 ramips: Fix too small rx buffer
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.

This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47116
2015-10-05 10:26:28 +00:00
John Crispin 6b4985b105 ramips: Fix setting of rx buffer length
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.

No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47115
2015-10-05 10:26:21 +00:00
John Crispin 1aab21df9f ramips: Allow to receive vlan over untag ports on MT7530
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.

It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.

The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 47114
2015-10-05 10:26:09 +00:00
John Crispin dd8f5abb23 ramips: Add build files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
    1: Spaces -> Tabs
    2: Removed some packages

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47113
2015-10-05 10:26:02 +00:00
John Crispin e6e373d348 ramips: Add DTS files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
  1: Merged most stuff into dtsi file
  2: Remove unnecessary empty lines.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47112
2015-10-05 10:25:53 +00:00
John Crispin c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin 7ad419a9f1 ralink: add irq to mt7628 gpio node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47076
2015-10-01 19:12:14 +00:00
John Crispin e1b1b0cbfd ralink: the mmc driver can now handle CD lines that are active low
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47074
2015-10-01 18:13:47 +00:00
John Crispin 9e1268b168 ralink: speed selection was broken in spi-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47073
2015-10-01 15:35:44 +00:00
John Crispin f453508b3e ramips: Fix pinmux functions for MT7621
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46963
2015-09-16 08:31:52 +00:00
John Crispin 3a149a2910 ramips: add mt7621/3/8 support to the I2C driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46959
2015-09-16 08:31:15 +00:00
John Crispin e6a9d5edf2 ramips: fix reported vendor name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46958
2015-09-16 08:31:10 +00:00
John Crispin 86a1e46b63 ramips: add proper mt7688 detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46957
2015-09-16 08:31:00 +00:00
John Crispin 85d5b9984d ramips: add speed and mode settings to spi-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46956
2015-09-16 08:30:43 +00:00
John Crispin 38c28154bd ramips: add get_direction() callback and irq support to gpio-mt7621
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46955
2015-09-16 08:30:17 +00:00
John Crispin 23d79b60ce ramips: more m7628 pinmux fixes
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46954
2015-09-16 08:30:06 +00:00
John Crispin 9473837653 ramips: add mt7628 pwm driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46953
2015-09-16 08:29:55 +00:00
John Crispin 9dfe1f6fbe ramips: make pinctrl work on newer socs
newer socs have 2 mux registers

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46952
2015-09-16 08:29:45 +00:00
John Crispin 710520d5c7 ramips: make the mt7628 spi driver work for both cs lines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46951
2015-09-16 08:29:40 +00:00
John Crispin 6f07b8a659 ramips: make the early_printk code detect which uart is used
only tested on mt7628

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46950
2015-09-16 08:29:31 +00:00
John Crispin 57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin 2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
Felix Fietkau fcee359813 ramips: fix chunked-io support for big flash chips (#20504)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46904
2015-09-14 06:54:15 +00:00
Felix Fietkau 1956cc7018 ramips: enable external amplifier for Xiaomi MiWiFi Mini
Attempt to boost the 2.4 GHz signal, currently very low.

Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>

SVN-Revision: 46891
2015-09-12 10:22:41 +00:00
Felix Fietkau d9857f5468 ramips: Enable RTC support for PBR-M1
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.

Enabling this option should fix the problem of the missing rtc device on
these boards.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46857
2015-09-11 16:32:58 +00:00
Jonas Gorski 7d6cff4882 kernel: update 3.18 to 3.18.21
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46768
2015-09-02 10:18:15 +00:00
Felix Fietkau 7747092ed1 ramips: fix devicetree corruption with some boot loaders if the caches are not ready at boot
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46766
2015-09-02 09:24:05 +00:00
Jonas Gorski efb2c403cf ramips: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46759
2015-08-30 12:18:14 +00:00
John Crispin 402c2d008b ramips: move patches around
0073 needs to applied afert 0102

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46667
2015-08-17 10:13:46 +00:00
John Crispin 0f155a330e ramips: base-files: optimize etc/diag.sh and etc/board.d/01_leds scripts
Instead of using board name provided explicitly as text in LED name, ex.:

[...]
mlwg2)
	status_led="mlwg2:blue:system"
[...]

use $board variable, which allows to combine together multiple boards with same color and LED names, ex:

[...]
mlw221|\
mlwg2)
	status_led="$board:blue:system"
[...]

The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46665
2015-08-17 06:24:47 +00:00
John Crispin 1a392636a5 ramips: use consistent naming scheme for LEDs
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
 * fixes wrong indentation
 * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
 * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
 * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46664
2015-08-17 06:24:34 +00:00
John Crispin eba4a143c6 ramips: reorder the sysupgrade script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46660
2015-08-17 06:18:38 +00:00
John Crispin aa4c6e27b4 ramips: reorder patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46659
2015-08-17 06:18:30 +00:00
John Crispin 87df7da757 ramips: Fix MT7621 pinmux bits for uart3, uart2, mdio
The MT7621 uses a 2 bit wide configuration of the sdhci, spi, mdio, pcie,
wdt, uart2 and uart3 in the GPIO_MODE register. It was correctly done
for sdhci, spi, pcie and wdt, The same has to be done for uart3, uart2
and mdio.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46645
2015-08-17 06:15:49 +00:00
John Crispin 09851afd33 ramips: Fix amount of MT7621 pins controlled by spi group
The PINS conntrolled by the SPI bits in the GPIO_MODE register is always
7 and not 8 for nand mode.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46644
2015-08-17 06:15:44 +00:00
John Crispin 9ed654e389 ramips: Fix uart2/uart3 pinmux order on MT7621
The uart3 setting in GPIO_MODE register is before the uart2 setting. Also
don't mix uart2 and uart3 function/groups.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46643
2015-08-17 06:15:34 +00:00
John Crispin f32116987f ramips: remove unnecessary LED declaration for WT1520 in diag.sh
This device doesn't have defined LEDs in its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46635
2015-08-17 06:03:42 +00:00
John Crispin 2f0449419f ramips: fix indentation, case statements structure and optimize base-files/etc/board.d/02_network
The following patch:
 * fixes wrong indentation
 * combines together boards with same configuration
 * removes unnecessary spaces
 * removes empty lines after ";;" and uses only "|\" (for consistency)
 * orders boards alphabetically

in base-files/etc/board.d/02_network script.

One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46634
2015-08-17 06:02:59 +00:00
John Crispin 4069a8e49c ramips: be consistent with case statement in base-files/lib/upgrade/platform.sh
Always use "|\" (without spaces) and keep boards in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46633
2015-08-17 06:01:49 +00:00
John Crispin a18b35a2f1 ramips: remove leading spaces, sort boards and optimize base-files/lib/ramips.sh
This patch:
 * fixes various mistakes (leading spaces, wrong or missing model names)
 * shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization)
 * sorts boards alphabetically

in base-files/lib/ramips.sh script.

Case statement was tested after above changes with simple script, which:
 * takes model string from dts{,i} file (model = "...")
 * provides this value as case input ($machine)
 * returns output ($name)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46632
2015-08-17 06:01:44 +00:00
John Crispin 57e614c179 ramips: fix various mistakes in subtargets *.mk profiles
This patch:
 * fixes wrong indentation
 * fixes wrong names and descriptions (ex. Dlink -> D-Link)
 * changes filenames to manufacturer names
 * moves oem/unknown manufacturers boards to misc.mk profiles
 * combines profiles for boards from the same manufacturers in one file (ex. Olimex)
 * fix profile files structure (keep the same convention as in other targets, ex. ar71xx)

in various .mk profiles, in ramips target.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46631
2015-08-17 06:01:38 +00:00
John Crispin 0d464c360f ramips: remove old code for Edimax BR-6524N
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46630
2015-08-17 06:01:23 +00:00
John Crispin 2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin 713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin 0bb270429d ramips: fix Edimax BR-6425 board name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46626
2015-08-17 05:59:57 +00:00
John Crispin 40f808600c ramips: fix Tenda W150M model name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46625
2015-08-17 05:59:47 +00:00
John Crispin b52ac01d27 ramips: fix Aigale Ai-BR100 dts and profile names
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46624
2015-08-17 05:59:36 +00:00
John Crispin 633c46a1d4 ramips: fix Olimex models, images and profiles names
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
 * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
 * changes filenames of dts and profile files
 * changes image filenames

for Olimex RT5350F-OLinuXino{,-EVB} devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46623
2015-08-17 05:59:29 +00:00
John Crispin 66f6c9e231 ramips: fix Sitecom WL-341v3 board and image names
The following patch changes:
 * board name from "wl341v3" to "wl-341v3"
 * dts filename
 * LED names in dts file

for Sitecom WL-341v3 device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46622
2015-08-17 05:59:12 +00:00
John Crispin 102073ca17 ramips: fix Argus ATP-52B board and image names
The following patch:
 * changes board name from "argus-atp52b" to "atp-52b"
 * changes dts filename
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Argus ATP-52B device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46621
2015-08-17 05:58:57 +00:00
John Crispin f38d42b8e4 ramips: fix Belkin F7C027 image name
This patch removes manufacturer from Belkin F7C027 image name ("belkinf7c027" -> "f7c027").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46620
2015-08-17 05:58:44 +00:00
John Crispin 5e84d173fa ramips: fix Asus RT-N56U dts filename
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46619
2015-08-17 05:58:35 +00:00
John Crispin 7bf1db0dcb ramips: fix UPVEL model names
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46618
2015-08-17 05:58:20 +00:00
John Crispin a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin 5a6690a7a6 ramips: fix Asus RP-N53 and Lenovo Y1{, S} image names
This patch:
 * fixes typo (rp_n53 -> rp-n53) in Asus RP-N53 image name
 * removes manufacturer from image names for Lenovo Y1{,S} devices

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46616
2015-08-17 05:58:07 +00:00
John Crispin 5e1ea4810b ramips: fix Asus WL-330N{, 3G} boards names
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46615
2015-08-17 05:57:55 +00:00
John Crispin f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin 553fea9f19 ramips: fix indentation and other mistakes in .dts{, i} files
The following patch fixes:
 * wrong indentations
 * doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
 * duplicate spacings
 * empty lines at end of files and after last child nodes
 * trailing and leading whitespace
 * unnecessary and commented-out code
 * missing empty lines between nodes and between properties and nodes
 * unnecessary empty lines between nodes properties [1]

in .dts{,i} files, for ramips target.

[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46613
2015-08-17 05:57:18 +00:00
Hauke Mehrtens 0b8643af4f kernel: update 3.18 to 3.18.20
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.20

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46570
2015-08-09 11:09:52 +00:00
Felix Fietkau ba05254353 ramips: Fix Ticket #20153 swap radio calibration data pointers on the RE6500
This patch fixes weak radio signal reported by nikola.georgiev

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46545
2015-08-02 15:08:14 +00:00
Felix Fietkau 92c41de105 ramips: swap radio calibration data pointers for DIR-860L
Fixes low 5 GHz tx power issues

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46497
2015-07-26 13:01:43 +00:00
John Crispin 1b6a6abf04 ramips: add additional uarts to mt7628.dtsi
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46477
2015-07-24 09:12:21 +00:00
John Crispin 37495247d2 ramips: make sd driver depend on mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46476
2015-07-24 09:12:16 +00:00
John Crispin 351a55ac29 ramips: add CD polling to sd driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46475
2015-07-24 09:12:10 +00:00
John Crispin ebe957fad6 ramips: various mt7688 pinmux fixes
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46474
2015-07-24 09:12:02 +00:00
John Crispin e04e44a223 ramips: add subtarget for mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46473
2015-07-24 09:11:56 +00:00
John Crispin 7449ea88db ramips: add clock strecthing support to i2c driver
fixes #19816

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46472
2015-07-24 09:11:42 +00:00
John Crispin dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00