35661401da
generate image for Linksys e3200
...
SVN-Revision: 33003
2012-08-05 13:14:00 +00:00
a71f347c30
brcm47xx: update gpio patch
...
SVN-Revision: 33001
2012-08-05 12:40:05 +00:00
1d40a652ee
brcm47xx: fix patch which moves the flash struct in wgt634u code
...
SVN-Revision: 33000
2012-08-05 12:39:15 +00:00
5f438c3565
W502V/ARV4525 wireless mac bugfix
...
The ARV4525 board init is passing the wrong offset to
arv_register_ath5k() resulting in a bogus mac.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 32993
2012-08-04 20:14:52 +00:00
0758996824
brcm47xx: use libgpio instaed of implementing the gpio interface ourself.
...
SVN-Revision: 32992
2012-08-04 19:46:25 +00:00
060b161ca6
cleanup patches
...
SVN-Revision: 32953
2012-08-03 08:53:02 +00:00
162e272b4b
nuport-mac: properly protect the phy interrupt handler
...
SVN-Revision: 32951
2012-08-02 18:13:17 +00:00
f45132d1d4
Codel: avoid a nul rec_inv_sqrt
...
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
Brought over from 3.5-stable
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 32950
2012-08-02 13:39:50 +00:00
c2d3274ffc
fixes i2c clock enable
...
SVN-Revision: 32949
2012-08-02 13:29:49 +00:00
e320a7e649
ar71xx: simplify misc IRQ handling
...
SVN-Revision: 32948
2012-08-02 11:25:49 +00:00
3e1e52a524
ar71xx: fix AR934X_EHCI_SIZE
...
SVN-Revision: 32947
2012-08-02 11:25:46 +00:00
b873051706
ar71xx: image: stop the switch from the lzma-loader on the TL-WR1043ND
...
SVN-Revision: 32946
2012-08-02 09:54:41 +00:00
e29d6bec6f
ar71xx: image: allow to use board specific code in the lzma-loader
...
SVN-Revision: 32945
2012-08-02 09:54:33 +00:00
79a8660d67
ar71xx: init switch hw_reset on the TL-WR1043ND board
...
SVN-Revision: 32944
2012-08-02 09:54:28 +00:00
e2782eae8e
generic: rtl836x: add hw_reset field to struct rtl8366_smi
...
It will be used to start/stop the switch if that is
supported by the given board.
SVN-Revision: 32943
2012-08-02 09:54:21 +00:00
614ca3cc9e
generic: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free calls
...
SVN-Revision: 32942
2012-08-02 09:54:13 +00:00
9f011e7225
add missing netmask to the network config
...
SVN-Revision: 32941
2012-08-01 22:09:13 +00:00
5133a44785
assume the link is up and full-duplex by default
...
SVN-Revision: 32940
2012-08-01 21:56:54 +00:00
56aac45139
add a default and suitable network config file
...
SVN-Revision: 32939
2012-08-01 21:56:49 +00:00
563400ef10
ar71xx: ew-dorin: added router firmware generation
...
[juhosg: remove dead code]
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32934
2012-08-01 12:24:57 +00:00
8eabe64e6b
ar71xx: ew-dorin: added USB support
...
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32933
2012-08-01 12:24:56 +00:00
1af4fd7660
ar71xx: Buffalo WLAE-AG300N wireless led patch
...
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932
2012-08-01 12:24:54 +00:00
010aec0619
ar71xx: Buffalo WLAE-AG300N initial support
...
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931
2012-08-01 12:24:52 +00:00
df48d71d72
resync defconfig enable XZ compression
...
SVN-Revision: 32930
2012-08-01 12:01:27 +00:00
3cd753408d
properly generate squashfs, jffs2 and initramfs images and kernels
...
SVN-Revision: 32927
2012-07-31 23:09:50 +00:00
c0561a42e7
disable crashlog on ARM platforms for the moment
...
It is currently badly broken on ARM, until fixed, disable it
SVN-Revision: 32926
2012-07-31 23:09:46 +00:00
f5f36911f0
add lantiq svip support
...
SVN-Revision: 32925
2012-07-31 18:49:54 +00:00
07c4524d33
bcm63xx: Add nb6 support (BCM6362 SoC base boards)
...
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
SVN-Revision: 32924
2012-07-31 14:27:47 +00:00
820c224029
bcm63xx: add basic bcm6362 support
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32923
2012-07-31 14:27:42 +00:00
dcd339ac9d
bcm63xx: enable usb for bcm6328
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32922
2012-07-31 14:27:34 +00:00
94d257a851
bcm63xx: update enetswitch driver
...
Update enetswith driver with latest fixes and additions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32921
2012-07-31 14:27:31 +00:00
fa75bd977a
bcm63xx: reorder patches
...
Fix the order and names of patches.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32920
2012-07-31 14:27:25 +00:00
d1ab4df0d6
move i2c module to target modules.mk
...
SVN-Revision: 32910
2012-07-29 13:20:51 +00:00
a5738c960a
resync config
...
SVN-Revision: 32908
2012-07-29 13:20:39 +00:00
17244dea00
use the same description as other omap platforms (without the dash)
...
SVN-Revision: 32907
2012-07-29 13:20:35 +00:00
ee0946a5f4
refresh pwm patch
...
SVN-Revision: 32905
2012-07-29 11:53:06 +00:00
101766fb00
clean up pwm patches and drivers
...
SVN-Revision: 32901
2012-07-28 20:47:08 +00:00
f0fe59648a
add config option CONFIG_I2C_MV64XXX to fix kirkwood build
...
SVN-Revision: 32898
2012-07-28 11:36:52 +00:00
67891c26ec
resync config
...
SVN-Revision: 32895
2012-07-27 15:35:15 +00:00
a4d699ccf0
fix DVA-G3810BN image generation
...
Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32894
2012-07-27 15:35:12 +00:00
c6813d33f3
add D-link DVA-G3810BN-TL-1 support
...
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32893
2012-07-27 15:35:09 +00:00
18206793b2
Add CT6376-1 board support
...
Added CT6373 devices instead of using NB4's devices, as Florian suggested.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32892
2012-07-27 15:35:05 +00:00
4acdbb1d87
Add brcmsmac profile
...
Add brcmsmac profile (kmod-brcmsmac + wpad-mini).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32890
2012-07-27 15:34:57 +00:00
0ba7b18cfd
Add leds back after migration to sysfs
...
atheros trunk moved to full sysfs gpiolib, but the leds were forgotten.
This restores the wlan led that was missing after switching from backfire
to trunk.
Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 32885
2012-07-26 17:06:55 +00:00
46611b2cbf
add more missing config symbols
...
SVN-Revision: 32884
2012-07-26 17:03:08 +00:00
ac30beaaa7
add more USB-related config symbols
...
SVN-Revision: 32883
2012-07-26 17:03:05 +00:00
a077e785cf
make sure target modules depend on the target
...
SVN-Revision: 32882
2012-07-26 17:03:02 +00:00
0c75abf527
bcma: update to version from wireless-testing tag master-2012-07-16
...
I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.
This also contains 3 additional patches fixing some bugs in bcma.
SVN-Revision: 32880
2012-07-26 15:42:18 +00:00
87a72d68f1
fix typo in modules.mk
...
This patch fixes a small typo in kmod-leds-wndr3700-usb description, where the board is for some reason made by NETGWR, not NETGEAR.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32870
2012-07-25 19:52:30 +00:00
d359d46182
make kmod-fb dependent on DISPLAY_SUPPORT and update targets accordingly
...
SVN-Revision: 32869
2012-07-25 19:36:19 +00:00
adc2b21be8
move isp116x driver to target specific modules.mk
...
SVN-Revision: 32865
2012-07-25 15:50:45 +00:00
1627b2bb4b
move rt305x-dwc driver to target specific modules.mk
...
SVN-Revision: 32864
2012-07-25 15:50:42 +00:00
c7a69869f7
move ubsec-ssb driver to target specific modules.mk
...
SVN-Revision: 32863
2012-07-25 15:50:38 +00:00
d1b2087a35
move ssb-gige to target specific modules.mk
...
SVN-Revision: 32862
2012-07-25 15:50:36 +00:00
c14d907b8b
move usb driver to target specific modules.mk
...
SVN-Revision: 32861
2012-07-25 15:50:33 +00:00
3b5a8548f4
move mmc driver to target specific modules.mk
...
SVN-Revision: 32859
2012-07-25 15:50:26 +00:00
18038c803c
move ixp4xx-eth to target specific modules.mk
...
SVN-Revision: 32858
2012-07-25 15:50:23 +00:00
4000de357e
move crypto module to target specific modules.mk
...
SVN-Revision: 32856
2012-07-25 15:50:16 +00:00
a282e37c09
move i2c driver to target modules.mk
...
SVN-Revision: 32855
2012-07-25 15:50:13 +00:00
accbc20045
move watchdog driver to target specific modules.mk
...
SVN-Revision: 32854
2012-07-25 15:50:10 +00:00
23ffbad602
move target specific spi modules
...
SVN-Revision: 32853
2012-07-25 15:50:04 +00:00
1859500829
move target specific leds modules to ar71xx modules.mk
...
SVN-Revision: 32852
2012-07-25 15:50:02 +00:00
c3b9a987b7
move leds modules back to target modules.mk
...
SVN-Revision: 32851
2012-07-25 15:49:57 +00:00
bca45d6d8a
move i2c modules back to target modules.mk
...
SVN-Revision: 32850
2012-07-25 15:49:54 +00:00
2bfb2a797c
move more x86-specific modules back to target modules.mk
...
SVN-Revision: 32848
2012-07-25 15:49:49 +00:00
d973768580
move x86 specific ide/pata modules to x86' modules.mk
...
SVN-Revision: 32846
2012-07-25 15:49:42 +00:00
e0837a51f0
brcm47xx: reorder patches so that the patches already in mainline linux will be applied at first.
...
SVN-Revision: 32845
2012-07-25 14:52:00 +00:00
ab2cb9ce61
add yet another framebuffer symbol
...
SVN-Revision: 32844
2012-07-25 14:01:57 +00:00
89a312bf48
split framebuffer helper modules to their own packages
...
SVN-Revision: 32843
2012-07-25 14:01:54 +00:00
ba9f6a46b1
remove broken flag
...
SVN-Revision: 32842
2012-07-25 14:01:51 +00:00
03c06178e3
package buttons driver separately
...
SVN-Revision: 32841
2012-07-25 14:01:49 +00:00
83b7462ac9
package cobalt lcd as a module
...
SVN-Revision: 32840
2012-07-25 14:01:46 +00:00
7ee4798be2
add unset CONFIG_FB_XGI to fix fullbuilds
...
SVN-Revision: 32836
2012-07-25 09:05:23 +00:00
94a550cc87
cleanup config-3.3, remove =m
...
SVN-Revision: 32835
2012-07-25 09:05:18 +00:00
1cbfa0c0f5
laguna: fix eeprom read buffer size during platform configuration
...
Increase the size of the buffer used for eeprom reads during the platform configuration of the Gateworks laguna. The model name read in is 16 bytes but the original buffer was only 8 bytes.
Signed-off-by: David Acker <dacker@rajant.com>
SVN-Revision: 32833
2012-07-25 08:01:38 +00:00
0e9e7dcd10
adds target used by rapsberry pi
...
Add support for Raspberry Pi / brcm2708 / 2835
Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
SVN-Revision: 32825
2012-07-24 20:39:17 +00:00
5e52619b76
DWC otg usb: compilation fixes and trivial bugfix in slave mode
...
Signed-of-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
SVN-Revision: 32823
2012-07-24 20:38:55 +00:00
799d6deab0
D-Link DAP-1350 initial support
...
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821
2012-07-24 20:38:43 +00:00
b891eec700
MI424WR - add rev D support
...
Add support for revision D of the MI424WR.
Rev D swaps LAN & WAN ports so this patch maintains
eth0 for LAN and eth1 for WAN. For details on rev D usage,
see http://wiki.openwrt.org/toh/actiontec/mi424wr
Signed-off-by: Jose Vasconcellos <jvasco@verizon.net>
SVN-Revision: 32820
2012-07-24 20:38:36 +00:00
03be8d08ac
initial LED configuration for Fonera 2.0n
...
Setup initial configuration for Wifi and USB LEDS of a Fonera 2.0n (ramips)
Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
SVN-Revision: 32819
2012-07-24 20:38:31 +00:00
2d2479a033
add ALL5002 userspace support
...
detect EEPROM, MAC addresses and support sysupgrade for the ALL5002
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32816
2012-07-24 20:38:14 +00:00
e219c3ac3a
enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.
...
Hope that this works, didn't have a chance to actually test it...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32815
2012-07-24 20:38:08 +00:00
a65eee9ac3
add image build for ALL5002
...
add image build for ALL5002
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32814
2012-07-24 20:38:03 +00:00
0a08a776fb
add support for Allnet ALL5002 to kernel
...
support ALL5002 in ramips/rt305x branch of the kernel.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32813
2012-07-24 20:37:56 +00:00
6641024f50
uart_clk on Rt3352F is always 40MHz
...
Currently, sys_clk/10 is used which is just wrong.
cpu_clk/10 would work for systems with 400MHz CPU clock.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32812
2012-07-24 20:37:50 +00:00
93dc8c8d1b
move omap specific modules to modules.mk
...
SVN-Revision: 32810
2012-07-24 19:43:54 +00:00
82c7e05d42
move n810 battery module to omap24 modules.mk
...
SVN-Revision: 32809
2012-07-24 19:43:49 +00:00
25e20b0b57
move target specific modules to target's module.mk
...
SVN-Revision: 32808
2012-07-24 19:43:45 +00:00
587f85ac20
package ep93xx framebuffer
...
SVN-Revision: 32807
2012-07-24 19:43:35 +00:00
5915c85d80
remove crypto symbols override
...
SVN-Revision: 32806
2012-07-24 19:43:31 +00:00
c238862651
add missing framebuffer related symbols
...
SVN-Revision: 32804
2012-07-24 19:43:23 +00:00
9f55e6f954
remove broken flag, since it works
...
SVN-Revision: 32803
2012-07-24 19:43:19 +00:00
c531ce0301
fix sound modules loading order and dependencies
...
SVN-Revision: 32802
2012-07-24 19:43:15 +00:00
598ef2a2e0
package ep93xx touchscreen driver as a module
...
SVN-Revision: 32799
2012-07-24 19:42:49 +00:00
0db5f35846
set DEVICE_TYPE to developerboard
...
SVN-Revision: 32798
2012-07-24 19:42:44 +00:00
5178c177dc
rebase config-3.3
...
SVN-Revision: 32797
2012-07-24 17:28:25 +00:00
53a6946bb4
fix tantos patch properly
...
SVN-Revision: 32796
2012-07-24 17:28:12 +00:00
6fe32d72a2
make tantos switch select ETHERNET_PACKET_MANGLE
...
SVN-Revision: 32795
2012-07-24 16:50:14 +00:00
48869ef7c0
move CONFIG_ETHERNET_PACKET_MANGLE to a generic config file
...
This broke falcon builds
SVN-Revision: 32794
2012-07-24 15:33:01 +00:00
b59bc92c6e
crashlog: fix dependency, add memblock support
...
SVN-Revision: 32787
2012-07-22 16:39:33 +00:00
b1f318de53
kernel: fix portability issues on the x86 specific relocs host tool, fixes build on mac os x
...
SVN-Revision: 32783
2012-07-20 12:28:50 +00:00
05340cc602
rename upgrade image to sysupgrade.bin for consistency
...
SVN-Revision: 32770
2012-07-17 16:47:57 +00:00
d243c1e1f2
add missing configuration symbols
...
SVN-Revision: 32769
2012-07-17 16:40:28 +00:00
f7dfd20f97
au1000: implement sysupgrade platform.sh
...
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32768
2012-07-17 16:40:24 +00:00
ac6bf6d62f
au1000: clean up profiles
...
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32767
2012-07-17 16:39:52 +00:00
b2d76e1e05
au1000: fix InternetBox idsel and remove broken flag
...
The following patch is necessary for the InternetBox (Surfbox) board-specific
idsel to work with newer kernels. Acutally I don't exactly understand why this
was not necessary before, but without the udelay, the MiniPCI adapter in slot 3
is not detected and set up correctly.
Also remove platform broken flag, it works.
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32766
2012-07-17 16:39:47 +00:00
21de1b9d85
ar71xx: enable I2C_GPIO, the PB44 board needs that
...
SVN-Revision: 32738
2012-07-15 17:52:52 +00:00
7daf851adf
ar71xx: fix PB44 board detection
...
SVN-Revision: 32737
2012-07-15 17:52:50 +00:00
c7fa38484c
ar71xx: use gpio_set_value_cansleep on sleeping GPIOs in ath79_spi
...
SVN-Revision: 32736
2012-07-15 17:52:48 +00:00
03a6d65c37
kernel: add Marvell SoC built-in RTC to modules
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32732
2012-07-15 14:25:30 +00:00
c727c2aacf
set DEVICE_TYPE to other to avoid pulling unecessary packages
...
SVN-Revision: 32731
2012-07-15 14:10:03 +00:00
a5d72815b5
add compatible property to pci node
...
SVN-Revision: 32730
2012-07-15 14:09:40 +00:00
b5578d83d5
use ohci_err() instead of err()
...
SVN-Revision: 32729
2012-07-15 14:09:32 +00:00
0e0b396663
make sure we properly unmap DMA mappings we created
...
SVN-Revision: 32728
2012-07-15 14:09:24 +00:00
0f0e42f28e
nuport-mac: add definitions of the various bits/masks used
...
SVN-Revision: 32727
2012-07-15 14:09:18 +00:00
c89e87d186
kirkwood: add support for seagate goflexnet and goflexhome
...
Signed-off-by: Martin Mueller <mm@sig21.net>
SVN-Revision: 32725
2012-07-15 12:18:29 +00:00
952ce3473d
kirkwood: revert config changes from r32053
...
SVN-Revision: 32719
2012-07-15 00:08:52 +00:00
33220828dc
ar71xx: build firmware image for the TP-Link TL-WDR4310 v1.0
...
The hardware for TP-Link TL-WDR4300 v1.1 and TL-WDR4310 v1.0 is
identical, but requires different firmware headers:
TL-WDR4300:
00000040 43 00 00 01 00 00 00 01 00 00 00 00 76 fb 83 40 |C...........v..@|
TL-WDR4310:
00000040 43 10 00 01 00 00 00 01 00 00 00 00 38 2b 50 6c |C...........8+Pl|
[juhosg: change commit message, use a different model name]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
SVN-Revision: 32683
2012-07-12 13:38:40 +00:00
372945185d
ramips: rt305x: add support for Edimax 3G-6200N
...
Support for Edimax 3G-6200N router with USB.
Signed-off-by: Lukasz Golebiowski <lgolebio@gmail.com>
SVN-Revision: 32682
2012-07-12 13:29:46 +00:00
e9af340016
generic: ocf: restore terminating entry of pci_id_table in hifnHIPP
...
SVN-Revision: 32680
2012-07-12 08:34:23 +00:00
d3c8852fd1
ar71xx: select ATH79_DEV_M25P80 for the WRT400N board
...
SVN-Revision: 32679
2012-07-12 08:34:22 +00:00
c75c895d24
ar71xx: airrouter power led support
...
This patch adds support for power led to Unifi Airrouter AP.
[juhosg:fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32678
2012-07-12 08:34:21 +00:00
466f010303
ar71xx: unifi reset button support
...
This patch adds support for reset button to Ubiquiti UniFi AP.
[juhosg: fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32677
2012-07-12 08:34:20 +00:00
5ce9c90ca8
ar71xx: airrouter reset button support
...
This patch adds support for reset button to Ubiquiti Airrouter AP.
[juhosg: fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32676
2012-07-12 08:34:18 +00:00
283021ac15
ocf: update to version 20120127
...
SVN-Revision: 32672
2012-07-11 23:38:14 +00:00
45d55161a6
kernel: bcma: update to version from wireless-testing tag master-2012-07-11
...
SVN-Revision: 32670
2012-07-11 22:17:05 +00:00
b94d9eb302
remove bcm63xx_pci_register() call in livebox board
...
SVN-Revision: 32661
2012-07-11 09:15:26 +00:00
f8446c3d4c
use physmap-flash on livebox ( #8677 )
...
SVN-Revision: 32660
2012-07-11 09:15:22 +00:00
8765e49fbe
nuport-mac: check netif_receive_skb() return value
...
We did not reassign status to netif_receive_skb() return value, we thus
almost always incremented the dropped counter because the descriptor status
value never matches the NET_RX_DROP.
SVN-Revision: 32659
2012-07-11 08:29:01 +00:00
93bf00ff36
fix typo on of_node_put()
...
SVN-Revision: 32653
2012-07-09 14:44:15 +00:00
bb1488e5e7
Detect alternative "cfe-" version bootloaders (found in 963281T_TEF board)
...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32643
2012-07-06 22:10:37 +00:00
fe015f399f
ar71xx: swizzle address for PCI byte/word access on AR71xx
...
Closes #11683 .
SVN-Revision: 32639
2012-07-06 16:33:12 +00:00
b39df5bb81
ar71xx: select SOC_AR933X and ATH79_DEV_WMAC for the OM2P board
...
SVN-Revision: 32638
2012-07-06 11:12:02 +00:00
e258367c19
ar71xx: merge new board patches into the generic patch
...
SVN-Revision: 32637
2012-07-06 11:12:01 +00:00
b020a7e7c3
ar71xx: OM2P LC sysupgrade patch
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 32635
2012-07-06 11:11:58 +00:00
110fd3525a
call of_node_put() on ethernet node
...
SVN-Revision: 32628
2012-07-05 18:46:55 +00:00
a8fab2cb78
fix EPHY clock bit definition after r32489
...
SVN-Revision: 32627
2012-07-05 18:46:52 +00:00
81681d7367
give an unique partition identifier for dLAN USB Extender Combined partition
...
SVN-Revision: 32626
2012-07-05 18:46:48 +00:00
eabf96dc22
ar71xx: set firmware version for the TL-WR2543N
...
This ensures that the resulting firmware can
be flashed from the latest (v3.13.17) offical
firmware.
SVN-Revision: 32617
2012-07-05 16:25:31 +00:00
7c932579fa
ar71xx: make 2.4GHz wlan LED work on the WR2543N
...
Because ath9k does not supports separate LEDs for
different bands yet, the 2.4GHz LED will show the
activity, even if the 5GHz band is selected.
SVN-Revision: 32615
2012-07-05 16:25:26 +00:00
b2f0476871
ar71xx: OM2P sysupgrade support
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 32613
2012-07-05 08:26:57 +00:00
797944d3f1
ar71xx: add support for the OpenMesh OM2P-LC board
...
Patch-by: Marek Linder <marek@open-mesh.com>
SVN-Revision: 32611
2012-07-05 08:26:53 +00:00
1ea2a3cfd8
ar71xx: add profile and build image for the Atheros AP136 reference board
...
SVN-Revision: 32609
2012-07-05 08:26:51 +00:00
b219848bfc
ar71xx: AP136 user-space support
...
SVN-Revision: 32608
2012-07-05 08:26:50 +00:00
f0cda65bb6
ar71xx: add initial support for the Qualcomm Atheros AP136 board
...
SVN-Revision: 32607
2012-07-05 08:26:48 +00:00
d1b237b335
ar71xx: add initial support for the QCA955X SoCs
...
SVN-Revision: 32606
2012-07-05 08:26:47 +00:00
7284cf73d6
ar71xx: refactor PCI code to allow registering multiple PCI controllers
...
SVN-Revision: 32605
2012-07-05 08:26:45 +00:00
6b8392eb12
generic: ar8216: start aneg on each PHY of the AR8327
...
SVN-Revision: 32604
2012-07-05 08:26:39 +00:00
0fdac1102d
add missing interrupts properties to some device nodes
...
SVN-Revision: 32603
2012-07-04 19:37:11 +00:00
bfef2d17eb
ar71xx: update the EW Dorin MTD layout, increase kernel partition size (requested by EW)
...
SVN-Revision: 32599
2012-07-04 10:55:56 +00:00
0a3e9c3148
bcm63xx: bcm63xx-spi does not depend on spi-bitbang
...
SVN-Revision: 32594
2012-07-03 21:42:17 +00:00
fad888a85c
bcm63xx: 96348A-122 improvements (Comtrend 5365)
...
1) Improve WLAN button.
2) Add 96348A-122 image.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32593
2012-07-03 21:42:15 +00:00
0c7e676342
bcm63xx: fix second caldata address calculation
...
thanks Noltari for spotting this.
SVN-Revision: 32592
2012-07-03 21:42:12 +00:00
988147111c
bcm63xx: update patches to latest upstream versions
...
SVN-Revision: 32591
2012-07-03 21:42:07 +00:00
1e2262df76
kernel: generic: spi: allow empty (un)prepare transfer
...
SVN-Revision: 32590
2012-07-03 21:42:03 +00:00
b8618fd3f2
ar71xx: improve MDIO busy wait code
...
SVN-Revision: 32586
2012-07-03 15:24:02 +00:00
86013d40d5
ar71xx: remove the built-in MTD map of the ALL0258N
...
Pass the mtd_layout via the kernel command line instead.
Also increase the kernel partition size to 1024k, so current kernel can fit in.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32585
2012-07-03 15:24:01 +00:00
4cdc4b1f36
refresh patches
...
SVN-Revision: 32581
2012-07-03 09:45:46 +00:00
bd9fa13c73
kernel: ssb/bcma: update to version from wireless-testing tag master-2012-07-02
...
SVN-Revision: 32580
2012-07-02 23:12:58 +00:00
52bae2d2bd
fix watchdog and rng drivers section mismatch ( #11767 )
...
SVN-Revision: 32522
2012-06-29 09:07:54 +00:00
5570b76642
ar71xx: detect and enable MIPS DSP extensions, AR9344 supports them ( fixes #11762 )
...
SVN-Revision: 32520
2012-06-28 16:05:08 +00:00
a5c684de26
kernel: switch openwrt default to TCP cubic from westwood (patch by Dave Täht)
...
Despite Westwood's theoretical advantages, in nearly
every benchmark we ran last year, TCP cubic won, whether it be
on correct RTT estimates, amount of buffering, responsiveness,
etc. on current hardware and software designs.
(both need timestamps on to work well, besides)
TCP cubic is better maintained and understood than westwood,
also.
While a scenario where westwood would win possibly exists,
there is too much buffering in the wifi stack in particular
at present, to see any improvement.
If you wish to exercise various TCPs under contention,
the current svn head of netperf (2.6) has options to switch
congestion control agorithms on the fly, as does iperf.
SVN-Revision: 32514
2012-06-27 22:32:47 +00:00
1d7878a38b
fix SPI clock frequency selection
...
SVN-Revision: 32512
2012-06-27 22:14:50 +00:00
41909c6568
kernel: add missing config symbol
...
SVN-Revision: 32498
2012-06-24 20:21:27 +00:00
eee358338c
ramips: mac address detection for Fonera 2.0n
...
Detect and apply MAC address of a Fonera 2.0n (ramips)
Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
Signed-off-by: Vasilis Tsiligiannis <b_tsiligiannis@silverton.gr>
SVN-Revision: 32490
2012-06-23 13:58:29 +00:00
81e8757da4
provide an early ioremap cookie of the system configuration register
...
SVN-Revision: 32489
2012-06-23 11:03:50 +00:00
98b2bc9189
group SYSDBG register defines in mcs814x.h
...
SVN-Revision: 32488
2012-06-23 11:03:45 +00:00
a8965f0005
make hardware.h a forward inclusion of mcs814x.h
...
mach/hardware.h is soon to be removed by upstream kernel
SVN-Revision: 32487
2012-06-23 11:03:40 +00:00
7c984552ed
remove platform specific initialization from ethernet driver
...
Hardware filtering must always be enabled as long as there is an Ethernet
device registered, and use device tree for setting the link activity and
buffer shifting enable/disable bit.
SVN-Revision: 32486
2012-06-23 11:03:35 +00:00
2c47bbc199
regroup interrupt controller register definitions in hardware.h
...
SVN-Revision: 32485
2012-06-23 11:03:29 +00:00
481c9faf20
remove handle_irq callback in board-mcs8140-dt.c
...
This should have been removed in r32470.
SVN-Revision: 32481
2012-06-21 12:20:47 +00:00
4b33e0996e
fix USB led triggers
...
SVN-Revision: 32474
2012-06-20 21:58:00 +00:00
a98c74164e
use generic uci defaults functions
...
SVN-Revision: 32473
2012-06-20 21:57:56 +00:00
007fa4d638
remove uselss cache invalidations
...
SVN-Revision: 32472
2012-06-20 21:57:53 +00:00
9a2367aa6d
improve ethernet driver debugging
...
SVN-Revision: 32471
2012-06-20 21:57:49 +00:00
3b0dba382b
do not use MULTI_IRQ_HANDLER it is bogus on our platform
...
This caused stalls in the Ethernet DMA block, so until properly
written and sorted out, fallback to the assembly version instead.
SVN-Revision: 32470
2012-06-20 21:57:45 +00:00
f45cd30543
verified to work - remove broken flag
...
SVN-Revision: 32469
2012-06-20 19:04:35 +00:00
1978c07539
Fix sysupgrade for squashfs, jffs2 and ext4 images
...
* use 'fsync' with 'dd' for image writing
* save config to boot partition
SVN-Revision: 32465
2012-06-19 22:36:53 +00:00
f4afa00862
add Moschip MSC814x support
...
This target currently only supports Moschip's MCS8140 SoC, but support
for other chips in the same family (MCS8142, MCS8144) will be easy to add.
Target support is entirely using Device Tree for probing peripherals.
Drivers support include:
- PCI
- USB 1 & 2
- watchdog
- random number generator
- UART
- timer
- internal Ethernet PHY
- Ethernet MAC core
Support for the following boards is included using Device Tree
- Devolo dLAN USB Extender
- Tigal RBT-832
SVN-Revision: 32462
2012-06-19 14:48:56 +00:00
7c87391c55
ar71xx: create profile and build image for the TL-WDR4300 board
...
SVN-Revision: 32461
2012-06-19 11:51:20 +00:00
2d97a52045
ar71xx: add user space support for the TL-WDR4300
...
SVN-Revision: 32460
2012-06-19 11:51:18 +00:00
8b9931fd27
ar71xx: add support for the TL-WDR4300 board
...
SVN-Revision: 32459
2012-06-19 11:51:17 +00:00
e6a10d5cdd
ar71xx: refresh patches
...
SVN-Revision: 32458
2012-06-19 11:51:15 +00:00
86c6543259
ar71xx: make AR8327 LEDs working on the DB120 board
...
SVN-Revision: 32457
2012-06-19 10:44:17 +00:00
b934fa2f16
generic: ar8216: allow to configure AR8327 LEDs via platform data
...
SVN-Revision: 32456
2012-06-19 10:44:16 +00:00
f509a87f2d
ar71xx: remove superfluous include of asm/mach-ath79/pci.h
...
SVN-Revision: 32455
2012-06-19 10:13:43 +00:00
1a1121158f
ar71xx: add a common function to configure USB power GPIOs
...
SVN-Revision: 32454
2012-06-19 10:13:41 +00:00
27fea0b6d7
ar71xx: correctly detect NETGEAR WNDRMAC
...
This patch helps properly detect a WNDRMAC device. Before this
patch the model is detected as "NETGEAR ?????????N".
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32453
2012-06-19 10:13:38 +00:00
ee9bc123fb
ar71xx: add USB LED support by default for WNDR3700/WNDR3800/WNDRMAC
...
This adds kmod-leds-wndr3700-usb package to a default build for
WNDR3700, WNDR3800 and WNDRMAC in order to support the green USB LED.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32452
2012-06-19 10:13:37 +00:00
833b4af816
ramips: rt305x: add support for the Petatel PSR-680W Wireless CDMA Router
...
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w
Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>
SVN-Revision: 32450
2012-06-19 09:52:15 +00:00
26cf21df02
ar71xx: add support for the embeddedwireless Dorin board (based on patch by embeddedwireless.de)
...
SVN-Revision: 32447
2012-06-19 00:22:04 +00:00
5d364d0ca1
ar71xx: add support for reading the MAC address from OTP ROM on AR933x
...
SVN-Revision: 32446
2012-06-19 00:21:58 +00:00
f06473f8ff
optimize kernel config for kvm_guest
...
This patch enables few extra kernel options for the kvm_guest subtarget:
- Tickless kernel to avoid timer ticks in idle guests, reduces CPU usage
- Enable paravirtualization steal time support
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 32436
2012-06-18 23:36:50 +00:00
cbac321164
remove inittab override
...
SVN-Revision: 32422
2012-06-18 11:50:37 +00:00
b89c81929e
fix SPI message control handling for BCM6338/6348
...
BCM6338 and BCM6338 have their MSG_CONTROL register width of 8-bits instead of
16-bits. We were previously using a 16-bits write which corrupted the first
byte of the TX FIFO. Also the message type was always set to Full-duplex even
in the case of half-duplex messages.
SVN-Revision: 32409
2012-06-17 16:17:29 +00:00
50958f5e03
kernel: replace the brcm47xx fuse workaround patches with a generic patch that applies to all mips targets
...
The dcache bug that it works around is a generic issue, not a brcm47xx cache quirk
SVN-Revision: 32395
2012-06-16 21:06:33 +00:00
b391548cf0
remove broken flags
...
Thanks to Nicolas Le Falher for testing on Bifferboard.
SVN-Revision: 32389
2012-06-16 16:45:28 +00:00
e3663ff907
use ttyS0 @ 115200 baud as default for KVM guests
...
SVN-Revision: 32384
2012-06-15 12:59:49 +00:00
1c80d9f21d
kirkwood: fix typo in uci-defaults/leds
...
Signed-off-by: Martin Mueller <mm@sig21.net>
SVN-Revision: 32343
2012-06-13 18:41:42 +00:00
dddf321b6e
ar71xx: swap the PHY address of the ethernet port of TL-MR3040/TL-MR11U similar to TL-MR3020 to fix ethernet link detection
...
SVN-Revision: 32336
2012-06-13 12:54:22 +00:00
Hauke Mehrtens
John Crispin
Florian Fainelli
Gabor Juhos
Jonas Gorski
Felix Fietkau
Luka Perkov
Vasilis Tsiligiannis
Mirko Vogt
Jo-Philipp Wich