CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).
This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.
With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.
This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).
The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.
However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules
Let's add them to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Kernel 4.14.96 got the new configuration option
CIFS_ALLOW_INSECURE_LEGACY which allows to deactivate support for old
and insecure SMB versions like 1.0 and 2.0. Still allow these old SMB
version and fix build problems which occurred because this option was
not defined.
This was found by build bot.
Fixes: 3662157d8b ("kernel: bump 4.14 to 4.14.96")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
It makes perfectly sense to also swap 32 bit reading in favor of actual size.
also backport this patch to kernel 4.19
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This reduces the needed modifications to the mainline Linux kernel and
also makes the regmap package work with an out of tree kernel which
does not have these modifications.
The regmap-core is only added when it is really build as a module.
The regmap-core is normally bool so it cannot be built as a module in an
unmodified kernel. When it is selected by on other kernel module it will
always be selected as build in and it also does not show up in
$(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module.
When it is not in $(LINUX_DIR)/modules.builtin the build system expects
it to be built as a .ko file.
Just check if the module is really there and only add it in that case.
This splits the regmap package into multiple packages, one for each bus type.
This way only the bus maps which are really needed have to be added.
This also splits the I2C, SPI and MMIO regmap into separate packages to not
require all these subsystems to build them, on an unmodified upstream kernel
this also causes problems in some situations.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
A missing upstream stable backport leads to the following build error:
CC drivers/mmc/host/sdhci-msm.o
drivers/mmc/host/sdhci-msm.c:1158:3: error: 'const struct sdhci_ops' has no member named 'write_w'
.write_w = sdhci_msm_write_w,
^~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: warning: excess elements in struct initializer
.write_w = sdhci_msm_write_w,
^~~~~~~~~~~~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: note: (near initialization for 'sdhci_msm_ops')
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/sdhci-msm.o' failed
Solve the issue by backporting commit
99d570da30 ("mmc: Kconfig: Enable CONFIG_MMC_SDHCI_IO_ACCESSORS")
from linux-stable.
Ref: 528508ae8b (commitcomment-32049231)
Fixes: 528508ae8b ("kernel: bump 4.14 to 4.14.95")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch replaces the current hack with a better
version of the RFC patch has been accepted upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Backport upstream patch:
Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch applies cleanly, so it doesn't cause errors while rebasing
patches. It results in redifinition of inode_still_linked, causing build
to fail when ubifs is enabled. Drop the patch.
Fixes: a37098a2d0 ("kernel: bump 4.19 to 4.19.16")
Reported-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This configuration option was added in kernel 4.15 and is missing in the
kernel 4.19 configuration.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many MIPS CPUs have optional CPU features which are not activates for
all CPU cores. Print the CPU options which are implemented in the core
in /proc/cpuinfo. This makes it possible to see what features are
supported and which are not supported. This should cover all standard
MIPS extensions, before it only printed information about the main MIPS
ASEs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes two build problems introduced with the recently added new
kernel module package.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.
Add:
kmod-pmbus-core
kmod-pmbus-zl6100
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This refreshes the kernel configuration for kernel 4.14.
First this was run for the legacy target:
make kernel_oldconfig
Then for all targets including the legacy target this was run:
make kernel_oldconfig CONFIG_TARGET=subtarget
The option CONFIG_104_QUAD_8 was added to the generic configuration
because it would have been automatically removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
It makes perfectly sense to also swap 32 bit reading in favor of actual size.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip. Its 32, 128 and
256 Mbits siblings are supported upstream but this particular size wasn't.
This commit includes patches for kernels 4.14 and 4.19.
Tested on a COMFAST CF-E120A v3 (ath79).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The WD MyBook Live SquashFS images didn't work anymore due to
a upstream regression in f2fs commit: 0cfe75c5b01199
("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
that got backported to 4.14.86 and landed in 4.18.
by Martin Blumenstingl:
|Treat "block_count" from struct f2fs_super_block as 64-bit little endian
|value in sanity_check_raw_super() because struct f2fs_super_block
|declares "block_count" as "__le64".
|
|This fixes a bug where the superblock validation fails on big endian
|devices with the following error:
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
|As result of this the partition cannot be mounted.
|
|With this patch applied the superblock validation works fine and the
|partition can be mounted again:
| F2FS-fs (sda1): Mounted with checkpoint version = 7c84
|
|My little endian x86-64 hardware was able to mount the partition without
|this fix.
|To confirm that mounting f2fs filesystems works on big endian machines
|again I tested this on a 32-bit MIPS big endian (lantiq) device.
Hopefully, this will do until Martin's patch moved through upstream
to -stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|In the patch "usb: simplify usbport trigger" together with
|"leds: triggers: add device attribute support" caused an
|regression for the usbport trigger. it will no longer
|enumerate any "ports" (i.e the sysfs directory stays empty)
|if the usb host drivers are fully initialized before the
|usbport trigger was loaded.
<https://marc.info/?l=linux-usb&m=154577101631079>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The configuration option was renamed with kernel 4.19 from
CONFIG_CC_STACKPROTECTOR to CONFIG_STACKPROTECTOR adapt the code to set
both options.
CONFIG_STACKPROTECTOR now sets the regular stack protector and
CONFIG_STACKPROTECTOR_STRONG activates the additional protection of more
functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With kernel 4.19 new configuration options for the compiler were added.
These are automatically selected and set, instead of having them in each
target configuration, put them into the generic configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=adcc81f148d733b7e8e641300c5590a2cdc13bf3
"Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")"
Without patch:
cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1823 /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1823 /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1823 /bin/busybox
77ec8000-77eed000 r-xp 00000000 1f:03 2296 /lib/libgcc_s.so.1
77eed000-77eee000 rwxp 00015000 1f:03 2296 /lib/libgcc_s.so.1
77eee000-77f81000 r-xp 00000000 1f:03 2470 /lib/libc.so
77f90000-77f92000 rwxp 00092000 1f:03 2470 /lib/libc.so
77f92000-77f94000 rwxp 00000000 00:00 0
7f946000-7f967000 rw-p 00000000 00:00 0 [stack]
7fefb000-7fefc000 rwxp 00000000 00:00 0
7ffac000-7ffad000 r--p 00000000 00:00 0 [vvar]
7ffad000-7ffae000 r-xp 00000000 00:00 0 [vdso]
Patch applied:
cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1825 /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1825 /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1825 /bin/busybox
77ed0000-77ef5000 r-xp 00000000 1f:03 2298 /lib/libgcc_s.so.1
77ef5000-77ef6000 rwxp 00015000 1f:03 2298 /lib/libgcc_s.so.1
77ef6000-77f89000 r-xp 00000000 1f:03 2474 /lib/libc.so
77f98000-77f9a000 rwxp 00092000 1f:03 2474 /lib/libc.so
77f9a000-77f9c000 rwxp 00000000 00:00 0
7fbed000-7fc0e000 rw-p 00000000 00:00 0 [stack]
7fefb000-7fefc000 r-xp 00000000 00:00 0
7fff6000-7fff7000 r--p 00000000 00:00 0 [vvar]
7fff7000-7fff8000 r-xp 00000000 00:00 0 [vdso]
Note lack of write permission to 7fefb000-7fefc000
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refresh all patches
Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch
Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.
Tested-on: ath79
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch, in a variety of forms, has been around since beginning 2016
as e756c2bb07, ending up in present form 0aa6c7df60 (kernel 4.4.13 bump)
and carried forward ever since.
There have been a number of MIPS kernel memory handling changes since,
including VDSO fixes that meant openwrt patches have been dropped with
no apparent fallout.
Simple tests (ntfs-3g) on a HIGHMEM 512MB mt7621 device have not turned
up data corruption issues which would otherwise be expected. Similarly
running on other MIPS based devices for the past 2 months hasn't turned
up anything obvious to retain this out of tree patch.
With thanks to Rosen Penev for testing on the known 'highmem' device and
Felix Fietkau for testing advice. Not putting acked-by as it's my fault
if it breaks :-)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89
Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""
Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch
Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.
Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While building 4.19 for ath79 with CONFIG_ALL_KMODS=y with verbose mode
enabled I was asked by kernel config about few symbols/modules so I'm
adding those missing symbols to the generic config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Originally, cns3xxx used it's own functions for mapping, reading and writing registers.
Upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
removed the internal PCI config write function in favor of the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by cns3xxx_pci_map_bus()
while the generic one pci_generic_config_write() actually expects the real address
as both the function and hardware are capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing
to the wrong registers on some ocasions.
First issue seen due to this:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER, located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C (CACHE_LINE_SIZE)
This seems to cause some slight instability when certain PCI devices are used.
Another issue example caused by this this is the PCI bus numbering,
where the primary bus is higher than the secondary, which is impossible.
Before:
00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 255
Bus: primary=02, secondary=01, subordinate=ff, sec-latency=0
After fix:
00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 255
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
And very likely some more ..
Fix all by omitting the alignment being done in the mapping function.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backort upstream patch which preserves oif of IPv6 link scoped packets.
The outgoing interface of IPv6 link scope packets can be changed by the
function ip6_route_me_harder. This is unwanted behavior for link local
packets and multicast packets as the outgoing interface is fixed and must
not be altered as it can break neighbor discovery and multicast listener
discovery.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Backport net: Allow class-e address assignment via ifconfig ioctl
While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.
While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.
https://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git/commit/?id=65cab850f0eeaa9180bd2e10a231964f33743edf
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
I've sent this one upstream. This patch is critical if you want to run
with "prove lock correctness" (lockdep) and you happen to have certain
mtd devices. The misuse of the uninitialized object is undefined
behaviour, but being zeroed it does not appear to have actually broken
anything other than the lockdep engine.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Disable Marvell's hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Problem description:
Multiple APs with inter-AP roaming connected to different ports,
when station moves from one AP on one port to another AP on another port,
traffic flow breaks down because the learning table is not updated.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
[Replaced with upstream version, move to generic]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.
Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_OF_NET depends on CONFIG_NVMEM in kernel 4.19. To fix some build
problems in mainline Linux kernel CONFIG_NVMEM was changed from tristate
to bool in commit 2a37ce25d9 ("nvmem: disallow modular CONFIG_NVMEM").
This patch in OpenWrt revert the upstream commit and changes
CONFIG_NVMEM back to tristate we just have to make sure to build this in
for all targets which select CONFIG_OF_NET.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_HW_RANDOM_TPM does not activate a separate kernel module any
more, but it only activates the random code in the tpm.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The b53 driver was added as a dsa driver into the mainline Linux kernel,
but we still use the swconfig based driver. The header file b53.h is
used by both drivers, but the swconfig one needs an extra member, add
this one in a patch to not overwrite the version shipped with the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our
own version with the patch based on the upstream version.
This will remove the ledtrig-netdev support from kernel 3.18, because I
not want to spend time on backporting it to 3.18. This will make it
easier to use the upstream version with kernel 4.19, by just not
applying this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have IPQ8064 AP161 board which has three GMAC's
* RGMII x2
* SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This reverts commit 7e88753ace.
Using subpartitions (hierarchical layout) resulted in calling MTD ops of
parent partition instead of master device ops. That was expected and
should work but testing revealed some bugs.
Apparently the way MTD_ERASE_PARTIAL is implemented in the OpenWrt
breaks something and using parent partition ops triggers using that
code.
On SmartRG SR400ac it was resulting in:
[ 225.487519] jffs2: Erase at 0x01ac0000 failed immediately: errno -22
on the second boot (for some reason erasing was starting over) and it
was breaking flash access in a long term.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This helper uses hierarchical partitions layout following the way
upstream parsers work. It's closer to what we should use when mainlining
our solutions. It also doesn't require hacky casting of struct
mtd_partition to the const.
THIS WILL AFFECT KERNEL PRINTING PARTITIONS IN THE LOG
Something like:
[ 3.930158] 0x0000004e0000-0x000001fb0000 : "rootfs_data"
will get replaced by:
[ 3.907338] Creating 1 MTD partitions on "rootfs":
[ 3.912142] 0x00000031d400-0x000001ded400 : "rootfs_data"
It's important to understand that "rootfs_data" in above example is a
*subpartition* of the "rootfs" now. To get absolute addresses (e.g. for
some debugging purposes) one has to add them to the "rootfs", e.g.
[ 3.912548] 0x0000001c2c00-0x000001fb0000 : "rootfs"
(0x1c2c00 + 0x31d400 = 0x4e0000)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Multicast ARL entries can have multiple destination ports. Get and dump
all destination ports of each entry, not just the lowest.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Driver crash when 'phydev->adjust_link' isn't provided.
This patch check if 'phydev->adjust_link' exist before
call the method.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds the feature to parse the existing cpu_port DT
property, which is used to specify which port is the cpu port
of the switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.
This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This allows us to use the bridge as a managed switch and gracefully
handle mixed tagged and untagged frames. Prior to this, the only
alternative was creating one bridge per vlan which quickly becomes a
nightmare and still won't let you mix both tagged and untagged frames on
the physical port without some complex ebtables magic.
This is in line with the notion that OpenWRT is the network go-to swiss
army knife when you need a nice set-and-forget, low maintenance box to
handle a specific task.
Current builds of the ip-bridge package already fully support this
feature so the only requirement is enabling the kernel config.
This is disabled by default so existing bridge configurations will not
be affected. This patch only gives the ability to turn it on with an
'ip link' command. If there is interest, I could look into making the
feature accessible via uci configuration.
It causes about 3.1% hit on raw bridging speed, which is relatively
trivial considering that I had to use 300 byte packets to strain the CPU
enough to notice a slowdown at all. The ER8 would chug along at wire
speed otherwise, and that's using only one core. Since the typical
bridge use case on OpenWRT is wireless, I doubt it would be noticeable
at all.
With BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414986 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 811 MBytes 680 Mbits/sec 0.000 ms
581210/3414986 (0%)
Without BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414990 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 836 MBytes 701 Mbits/sec 0.000 ms
493950/3414990 (0%)
In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a
0.002% hit. The exact 16KB is probably just due to how the kernel is
compressed.
Suggested-by: Jonathan Thibault <jonathan@navigue.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
No single target/arch uses it and most likely there is no need to make
such a potential code target/arch specific.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If "compatible" is being used that should trigger a proper parser
directly. It's more reliable thanks to not trying parsers one by one. In
such case partition shouldn't be split automatically to avoid parsing it
twice.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently, the b53 MDIO switch driver registers the switch on
config-init and not on device probe. Because of this, the switch
gets added every time the associated interface comes up.
This commit fixes this behavior by registering the switch on device
probe.
Compile- and run-tested on OCEDO Koala.
Signed-off-by: David Bauer <mail@david-bauer.net>
It makes more sense to add run_parsers_by_type() in a patch that
introduces parser types. That makes the other one just add a code using
it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There was a bug in ubifs related to the O_TMPFILE. When reapplying
changes after power cut data could be lost. This problem was exposed by
overlayfs and the upstream commit 3a1e819b4e80 ("ovl: store file handle
of lower inode on copy up").
This fixes a regression introduced when switching from 4.9 to 4.14.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It has been rejected upstream and instead a nice/more generic solution
has been implemented. It's possible now to describe partitions format
using "compatible" DT string.
No OpenWrt target uses "linux,part-probe" anymore, leave it only in case
some forks need it. It will be dropped with support for new kernels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:
- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G
and probably other Mikrotik boards need this patch as well.
The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/
Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Compaction is the only memory management component to form high order (larger
physically contiguous) memory blocks reliably. The page allocator relies on
compaction heavily and the lack of the feature can lead to unexpected OOM
killer invocations for high order memory requests. You shouldn't disable this
option unless there really is a strong reason for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
Optimized inlining was disabled by default when gcc 4 was still
relatively new. By now, all gcc versions handle this well and there
seems to be no real reason to keep it x86-only.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The cache coloring problem on MIPS CPUs was fixed with kernel 4.9.129 of
the kernel 4.9 branch. Activate VDSO support for MIPS again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds some configuration options which are selectable when the
layerscape armv7 target is compiled.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds some configuration options which are selectable when the
samsung target is compiled.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport an additional patch from 4.16 for nftables.
This fixes a build problem recently introduced.
Fixes: f57806b56e ("kernel: generic: Fix nftables inet table breakage")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit b7265c59ab ("kernel: backport a series of netfilter cleanup
patches to 4.14") added patch 302-netfilter-nf_tables_inet-don-t-use-
multihook-infrast.patch. That patch switches the netfilter core in the
kernel to use the new native NFPROTO_INET support. Unfortunately, the
new native NFPROTO_INET support does not exist in 4.14 and was not
backported along with this patchset. As such, nftables inet tables never
see any traffic.
As an example the following nft counter rule should increment for every
packet coming into the box, but never will:
nft add table inet foo
nft add chain inet foo bar { type filter hook input priority 0\; }
nft add rule inet foo bar counter
This commit pulls in the required backport patches to add the new
native NFPROTO_INET support, and thus restore nftables inet table
functionality.
Tested on Turris Omnia (mvebu)
Fixes: b7265c59ab ("kernel: backport a series of netfilter cleanup ...")
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
kernel upstream commit 9efcaa7c4afba5628f2650a76f69c798f47eeb18 to 4.14
itself a backport of 0f02cfbc3d9e413d450d8d0fd660077c23f67eff has
resolved the cache line issues that led to us disabling VDSO by default
on MIPS.
Remove our force disable patch:
pending-4.14/206-mips-disable-vdso.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Yangbo Lu
Rosen Penev
Koen Vandeputte
Daniel Engberg
Tony Ambardar
Felix Fietkau
HsiuWen Yen
Petr Štetiar
Hauke Mehrtens
Hauke Mehrtens
Jo-Philipp Wich
Christian Lamparter
Kevin Darbyshire-Bryant
Mathias Kresin
Stijn Tintel
Chuanhong Guo
Pawel Dembicki
Rafał Miłecki
Roger Pueyo Centelles
Hans Dedecker
Daniel Santos
Brett Mastbergen
Anderson Luiz Alves
Deng Qingfang
David Bauer
Ram Chandra Jangir
Günther Kelleter
Daniel Golle
Baptiste Jonglez