Add configure argument --disable-ipv6 when ipv6 is deselected.
Add fix-non-ipv6-builds.patch as long there is no new upstream
release.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
When bumping Curl to 7.62.0 in commit 278e4eba09 I did not include the fixed
CVEs in the commit message; this commit fixes this.
The following CVEs were fixed in 7.62.0 :
CVE-2018-16839
CVE-2018-16840
CVE-2018-16842
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The NBG6617's boardfile was merged and this device can
now switch to the upstream ath10k board-2.bin.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates the board-2.bin for the default
IPQ4019, QCA9984 and QCA9888 ath10k-firmware-xyz-ct
and -ct-htt firmwares.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch replaces the custom autoload quirk of the
RT-AC58U with a bootargs-append overwrite.
The vendor's u-boot doesn't leave the bootargs / cmdline alone,
so the it can't be overwritten in any other way right now...
And of course, this will be a lot of fun to deal with once
the device switches to the new spi-nand subsystem.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This updates these two files to commit 2fa97a8a0ed3 ("config.guess
(amd64:CYGWIN*:*:*, x86_64:CYGWIN*:*:*): Set master") which is the
current master of
https://git.savannah.gnu.org/gitweb/?p=config.git;a=summary
This contains updates for multiple architectures and will unbreak the
build on the x32 ABI.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Also update the U-Boot BSP patch for I2SE Duckbill devices
and remove upstreamed patch for LibreSSL support.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Some package (e.g. libunbound) depend on OPENSSL_WITH_DEPRECATED. In some
situations it may happen that libunbound and openssl are only pulled in as
build dependencies, but are not enabled in .config.
In such cases, the defaults of symbols like OPENSSL_WITH_DEPRECATED are
ignored (as the whole symbol depends on PACKAGE_libopenssl), and config
symbol dependencies of libunbound aren't effective either (as libunbound
is not actually enabled).
This commit works around the issue by introducing a hidden negated symbol
OPENSSL_NO_DEPRECATED, which is always disabled when PACKAGE_libopenssl is
disabled, and ensures that OpenSSL is built with deprecated APIs in this
case. A user can still manage to break the build by explicitly enabling
libopenssl and disabling OPENSSL_WITH_DEPRECATED; the interaction between
build dependencies and config symbols will require further discussion.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Install following as config files (600) perms instead of as data (644)
/usr/share/dnsmasq/dhcpbogushostname.conf
/usr/share/dnsmasq/trust-anchors.conf
/usr/share/dnsmasq/rfc6761.conf
/etc/hotplug.d/ntp/25-dnsmasqsec
/etc/config/dhcp
/etc/dnsmasq.conf
dnsmasq reads relevant config files before dropping root privilege and
running as dnsmasq:dnsmasq
ntpd runs as root so the hotplug script is still accessible
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kernel 4.14 is pretty large causing a build error as the partition is too small.
Expand the kernel partition a bit to make it fit.
* ubnt-uap-pro
* ubnt-unifi-outdoor-plus
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This target causes a build failure as the kernel image does not fit
into the kernel partition.
As the kernel is located behind the rootfs, it cannot be enlarged
as the boot entry location would get altered.
Disable this target for now.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
These targets are already defined as having a dynamic partition
but the safeloader was not adapted for them.
This causes a build warning for the sysupgrade image being too big.
Targets:
- c58-v1
- c60-v1
- c60-v2
- TL-WR1043 v5
- TL-WR902AC v1
- TL-WR942N V1
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5
Fixes build issues seen due to the kernel being too big
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.
RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success
Tested on RE450, device boots and was used to send this patch.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This changes the OCEDO Koala flash-layout to a unified firmware
partition, thus making the ar71xx-generic kernel fit in flash.
Compile and runtested on OCEDO Koala.
Signed-off-by: David Bauer <mail@david-bauer.net>
[small title reword]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
USB support doesn't necessarily mean that there's
PCI support available so move that to the drivers
which requires PCI support. This applies to the
sunxi platform for instance.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix mt76x0e]
0b8b15f mt7603: use common mmio mcu struct
d612e2e mt76: mt76x02: skip station tx status for non-sta wcid entries
d89d84b mt76: mt76x02: only override control->sta on sw-encrypted tx
9d59d2a mt76: add support for reporting tx status with skb
ed17ba2 mt7603: use common tx status handling code
14b6c59 mt76x0: use band parameter for LC calibration
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Upgrade 88W8997 firmware to 8.4.0.52.
Removed unnecessary firmware settings.
Added vendor events.
Fixed crash problem when module is removed.
Modified the code to protect tx queues.
Signed-off-by: Jonathan Lancett <j.lancett@ntlworld.com>
[tidy commit message]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
77b4b8231e signal: Use correct type for si_band in siginfo_t [BZ #23562]
5bdb6897fc Fix race in pthread_mutex_lock while promoting to PTHREAD_MUTEX_ELISION_NP [BZ #23275]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add the most recent supported firmware file for the Intel 9000 and
9260 wireless chips. The API version 41 is not yet supported by the driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472
Build will fail if system 'ar' does not support deterministic builds.
e.g. macOS with Xcode toolchain
Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Go for openwrt passes pkg-config arguments in the format of
pkg-config --cflags -- pkg-name
which in turn will be passed down to the real pkg-config as something
like
pkg-config.real --cflags -- pkg-name --define...
and causes the real pkg-config implementation to missinterpret the given
argument list.
This also helps to fix https://github.com/golang/go/issues/27940
Signed-off-by: Arthur Skowronek <arthur.skowronek@tuta.io>
Kalles ath10k PR was finally merged so update linux-firmware to
include those changes.
This is needed since disabling ath10k-firmware a lot of custom BDF-s
in board-2.bin-s are not available in previously outdated linux-firmware
board-2.bin-s.
This also includes support for boards currently using ipq-wifi and other
WIP ones.
Runtime tested on 8devices Jalapeno.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WNDR4700 and the MBL have a dedicated HDD activity LED.
This patch adds the default led triggers to the DTS and
removes the entries in 01_leds.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Alexander Couzens
Martin Weinelt
Hans Dedecker
Christian Lamparter
Rosen Penev
Daniel Engberg
Hauke Mehrtens
Thorsten Glaser
Michael Heimpold
Hannu Nyman
Kabuli Chana
Thomas Fuzeau
Matthias Schiffer
Kevin Darbyshire-Bryant
Koen Vandeputte
Radek Dostál
David Bauer
Mathias Kresin
YuheiOKAWA
Roger Pueyo Centelles
Felix Fietkau
Philip Prindeville
Jonathan Lancett
Rafał Miłecki
Ryan Mounce
Arthur Skowronek
Yufei Miao
Roman Bazalevskiy
Deng Qingfang
Robert Marko