The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.
Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1
group mode 1 mode 2 hlk-rm04 pin & export
i2c i2c_sd gpio1 (pin 8, hlk-rm04:gpio0)
i2c i2c_sclk gpio2 (pin 9, hlk-rm04:gpio1)
reference:
http://www.hlktech.net/product_detail.php?ProId=39http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48664
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48663
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48662
On systems that have an RTC prefer it to the file-based time fixup (i.e.
use hwclock when there is a permanent clock instead of the faked up time
logic that is needed when there is not RTC).
We can't rely on hctosys kernel feature either as we're usually using
RTC as kernel modules which are usually being loaded after hctosys was
run, leading in the following error:
hctosys: unable to open rtc device (rtc0)
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48661
With the backport of the kernel 4.5 pinctrl-xway patches (3551609d &
826bca29) the pinmux group "spi" was splitted into "spi_di", "spi_do" &
"spi_clk". But the no longer existing group "spi" is still used by some
device tree source files.
This fixes the detection of the wireless chipset of the VGV7510KW22.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48658
The stock u-boot doesn't disable unused flash banks. Therefore, the nand
driver tries to initialize a not connected NOR flash and the device
hangs on boot.
Workaround the issue by selecting the second flash bank (NAND).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48657
iptables is the only exception in the package tree, causing patch
behaviour to be inconsistent on this package.
Signed-off-by: Rick van der Zwet <rick.vanderzwet@anywi.com>
SVN-Revision: 48643
Curent ARC toolchain fails to build libstdc++ if -fno-plt is used.
Lots of following error messages appear:
------------------->8------------------
...
staging_dir/toolchain-arc_arc700_gcc-arc-2015.06_uClibc-1.0.9/arc-openwrt-linux-uclibc/bin/ld:
BFD (GNU Binutils) 2.23.2 assertion fail elf32-arc.c:2786
collect2: error: ld returned 1 exit status
------------------->8------------------
In newer binutils (still in development) for ARC rewritten from
scratch this seem to not happen, so once new binutils for ARC hit
the street this patch might be reverted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48642
It's not really supported yet as it still fails with:
brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48640
Recently TRX checking code was changed to detect Seama format and don't
abort whole writing operation because of it. This isn't a good long-term
solution. It's a poor idea to teach every format handler recognizing all
possible formats. Instead it should be handled in a generic code which
should run check depending on the detected format.
This will also allow further improvements like fixing formats other than
TRX after replacing JFFS2.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48639
Supported syntax is inspired by ethtool. Example usages:
swconfig dev switch0 port 2 set link "duplex half speed 100"
swconfig dev switch0 port 2 set link "autoneg on"
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48624
When dealing with Broadcom hardware we can simply use swconfig's generic
helper, we just need to do some validation of requested state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48623
Thanks to this change swconfig can access port PHYs e.g. when setting
port link state with a generic helper.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48622
It's quite common for switches to have PHY per port so adding a generic
helper setting link state will help many drivers. It just needs an API
to access PHYs which this patch also adds.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48621
This fixes the following security problems:
CVE-2016-0754: remote file name path traversal in curl tool for Windows
http://curl.haxx.se/docs/adv_20160127A.html
CVE-2016-0755: NTLM credentials not-checked for proxy connection re-use
http://curl.haxx.se/docs/adv_20160127B.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48614
John Crispin
Felix Fietkau
Rafał Miłecki
Zoltan Herpai
Hauke Mehrtens