This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42194
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 42179
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41839
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41838
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board
Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN
Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41680
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41632
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41452
Without this, the ports all end up on vlan 1. This enables a separate
WAN port that works.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41216
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
The first switch case is default case. Then it will only
match default case. cause not update the lan/wan mac address.
And in the default switch case the param lan_mac is empty.
it will case error message 'arithmetic syntax error' when
call macaddr_add function.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40910
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40908
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
SVN-Revision: 40907
Felix Fietkau
John Crispin
Imre Kaloz