mirror of https://github.com/hak5/openwrt.git
ath79: add support for Netgear WNR2200
This patch adds ath79 support for Netgear WNR2200. Router was previously supported by ar71xx target only (8 MiB variant). Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and 16 MiB for Russia and China markets. Apart from flash size both variants share the same hardware specification. Specification ============= * Description: Netgear WNR2200 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 64 MiB * Flash: 8 MiB or 16 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 7808 KiB or 16000 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_generic=y CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>master
Michal Cieslakiewicz
John Crispin
parent
c2675bb0ce
commit
f85d56bb03
|
|
@ -22,6 +22,8 @@ glinet,gl-ar300m-nor|\
|
|||
librerouter,librerouter-v1|\
|
||||
netgear,ex6400|\
|
||||
netgear,ex7300|\
|
||||
netgear,wnr2200-8m|\
|
||||
netgear,wnr2200-16m|\
|
||||
ocedo,koala|\
|
||||
ocedo,raccoon|\
|
||||
openmesh,om5p-ac-v2|\
|
||||
|
|
|
|||
|
|
@ -0,0 +1,34 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "ar7241_netgear_wnr2200.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "netgear,wnr2200-16m", "qca,ar7241";
|
||||
model = "Netgear WNR2200 (16M)";
|
||||
};
|
||||
|
||||
&partitions {
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x40000 0x10000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x50000 0xfa0000>;
|
||||
compatible = "netgear,uimage";
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,34 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "ar7241_netgear_wnr2200.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "netgear,wnr2200-8m", "qca,ar7241";
|
||||
model = "Netgear WNR2200 (8M)";
|
||||
};
|
||||
|
||||
&partitions {
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x40000 0x10000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x50000 0x7a0000>;
|
||||
compatible = "netgear,uimage";
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,207 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar7241.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power_amber;
|
||||
led-failsafe = &power_amber;
|
||||
led-running = &power_green;
|
||||
led-upgrade = &power_amber;
|
||||
label-mac-device = ð1;
|
||||
};
|
||||
|
||||
ath9k-keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&ath9k 3 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>;
|
||||
|
||||
wan_green {
|
||||
label = "netgear:green:wan";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan_amber {
|
||||
label = "netgear:amber:wan";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan1_green {
|
||||
label = "netgear:green:lan1";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan1_amber {
|
||||
label = "netgear:amber:lan1";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan2_green {
|
||||
label = "netgear:green:lan2";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan2_amber {
|
||||
label = "netgear:amber:lan2";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan3_green {
|
||||
label = "netgear:green:lan3";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan3_amber {
|
||||
label = "netgear:amber:lan3";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan4_green {
|
||||
label = "netgear:green:lan4";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan4_amber {
|
||||
label = "netgear:amber:lan4";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps_green {
|
||||
label = "netgear:green:wps";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb_green {
|
||||
label = "netgear:green:usb";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&hub_port>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
};
|
||||
|
||||
ath9k-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power_green: power_green {
|
||||
label = "netgear:green:power";
|
||||
gpios = <&ath9k 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_amber: power_amber {
|
||||
label = "netgear:amber:power";
|
||||
gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
wlan_blue {
|
||||
label = "netgear:blue:wlan";
|
||||
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qca,ar7241-eth", "syscon", "simple-mfd";
|
||||
mtd-mac-address = <&art 0x6>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
ath9k: wifi@0,0 {
|
||||
compatible = "pci168c,002e";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
qca,no-eeprom;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
|
||||
usb_power {
|
||||
gpio-hog;
|
||||
line-name = "netgear:power:usb";
|
||||
gpios = <4 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
hub_port: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
|
@ -103,6 +103,18 @@ glinet,gl-ar300m-lite)
|
|||
glinet,gl-x750)
|
||||
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
|
||||
;;
|
||||
netgear,wnr2200-8m|\
|
||||
netgear,wnr2200-16m)
|
||||
ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0"
|
||||
ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04"
|
||||
ucidef_set_led_switch "lan2green" "LAN2 (green)" "netgear:green:lan2" "switch0" "0x04" "0x04"
|
||||
ucidef_set_led_switch "lan3green" "LAN3 (green)" "netgear:green:lan3" "switch0" "0x08" "0x04"
|
||||
ucidef_set_led_switch "lan4green" "LAN4 (green)" "netgear:green:lan4" "switch0" "0x10" "0x04"
|
||||
ucidef_set_led_switch "lan1amber" "LAN1 (amber)" "netgear:amber:lan1" "switch0" "0x02" "0x02"
|
||||
ucidef_set_led_switch "lan2amber" "LAN2 (amber)" "netgear:amber:lan2" "switch0" "0x04" "0x02"
|
||||
ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "netgear:amber:lan3" "switch0" "0x08" "0x02"
|
||||
ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "netgear:amber:lan4" "switch0" "0x10" "0x02"
|
||||
;;
|
||||
pcs,cap324)
|
||||
ucidef_set_led_netdev "lan" "LAN" "pcs:lan:green" "eth0"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -184,6 +184,12 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch_port_attr "switch0" 2 led 9
|
||||
ucidef_add_switch_port_attr "switch0" 5 led 2
|
||||
;;
|
||||
netgear,wnr2200-8m|\
|
||||
netgear,wnr2200-16m)
|
||||
ucidef_set_interface_wan "eth0"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
phicomm,k2t)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
||||
|
|
|
|||
|
|
@ -76,6 +76,8 @@ case "$FIRMWARE" in
|
|||
winchannel,wb2000)
|
||||
caldata_extract "art" 0x5000 0x440
|
||||
;;
|
||||
netgear,wnr2200-8m|\
|
||||
netgear,wnr2200-16m|\
|
||||
pcs,cap324|\
|
||||
tplink,tl-wr2543-v1|\
|
||||
tplink,tl-wr842n-v1|\
|
||||
|
|
|
|||
|
|
@ -794,6 +794,40 @@ define Device/netgear_wndr3800ch
|
|||
endef
|
||||
TARGET_DEVICES += netgear_wndr3800ch
|
||||
|
||||
define Device/netgear_wnr2200_common
|
||||
ATH_SOC := ar7241
|
||||
DEVICE_MODEL := WNR2200
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
||||
NETGEAR_KERNEL_MAGIC := 0x32323030
|
||||
NETGEAR_BOARD_ID := wnr2200
|
||||
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | \
|
||||
append-rootfs | pad-rootfs
|
||||
$(Device/netgear_ath79)
|
||||
endef
|
||||
|
||||
define Device/netgear_wnr2200-8m
|
||||
$(Device/netgear_wnr2200_common)
|
||||
DEVICE_VARIANT := 8M
|
||||
NETGEAR_HW_ID := 29763600+08+64
|
||||
IMAGE_SIZE := 7808k
|
||||
IMAGES += factory-NA.img
|
||||
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
|
||||
check-size $$$$(IMAGE_SIZE)
|
||||
SUPPORTED_DEVICES += wnr2200
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wnr2200-8m
|
||||
|
||||
define Device/netgear_wnr2200-16m
|
||||
$(Device/netgear_wnr2200_common)
|
||||
DEVICE_VARIANT := 16M
|
||||
DEVICE_ALT0_VENDOR := NETGEAR
|
||||
DEVICE_ALT0_MODEL := WNR2200
|
||||
DEVICE_ALT0_VARIANT := CN/RU
|
||||
NETGEAR_HW_ID :=
|
||||
IMAGE_SIZE := 16000k
|
||||
endef
|
||||
TARGET_DEVICES += netgear_wnr2200-16m
|
||||
|
||||
define Device/ocedo_koala
|
||||
ATH_SOC := qca9558
|
||||
DEVICE_VENDOR := Ocedo
|
||||
|
|
|
|||
Loading…
Reference in New Issue