mirror of https://github.com/hak5/openwrt.git
ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
master
Piotr Dymacz
parent
8016f64864
commit
e5d4c09667
|
|
@ -0,0 +1,32 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "qca9563_yuncore_xd4200.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "yuncore,a782", "qca,qca9563";
|
||||
model = "YunCore A782";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system: system {
|
||||
label = "a782:red:system";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "a782:green:wlan2g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,32 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "qca9563_yuncore_xd4200.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "yuncore,xd4200", "qca,qca9563";
|
||||
model = "YunCore XD4200";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_system;
|
||||
led-failsafe = &led_system;
|
||||
led-running = &led_system;
|
||||
led-upgrade = &led_system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_system: system {
|
||||
label = "xd4200:blue:system";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "xd4200:blue:wlan2g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,122 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x03000101 0x00000101 0x00001919>;
|
||||
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
||||
0x10 0x81000080 /* POWER_ON_STRIP */
|
||||
0x50 0xcf37cf37 /* LED_CTRL0 */
|
||||
0x54 0xcf37cf37 /* LED_CTRL1 */
|
||||
0x58 0xcf37cf37 /* LED_CTRL2 */
|
||||
0x5c 0x0000c300 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "pci168c,0056";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x050000 0xfa0000>;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
|
@ -164,7 +164,9 @@ ath79_setup_interfaces()
|
|||
nec,wg1200cr|\
|
||||
ubnt,nanostation-ac|\
|
||||
ubnt,unifiac-mesh-pro|\
|
||||
ubnt,unifiac-pro)
|
||||
ubnt,unifiac-pro|\
|
||||
yuncore,a782|\
|
||||
yuncore,xd4200)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:wan"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -154,6 +154,12 @@ case "$FIRMWARE" in
|
|||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
yuncore,a782|\
|
||||
yuncore,xd4200)
|
||||
caldata_extract "art" 0x5000 0x2f20
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
*)
|
||||
|
|
|
|||
|
|
@ -1040,6 +1040,28 @@ define Device/yuncore_a770
|
|||
endef
|
||||
TARGET_DEVICES += yuncore_a770
|
||||
|
||||
define Device/yuncore_a782
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_VENDOR := YunCore
|
||||
DEVICE_MODEL := A782
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
IMAGE_SIZE := 16000k
|
||||
IMAGES += tftp.bin
|
||||
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_a782
|
||||
|
||||
define Device/yuncore_xd4200
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_VENDOR := YunCore
|
||||
DEVICE_MODEL := XD4200
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||||
IMAGE_SIZE := 16000k
|
||||
IMAGES += tftp.bin
|
||||
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_xd4200
|
||||
|
||||
define Device/zbtlink_zbt-wd323
|
||||
ATH_SOC := ar9344
|
||||
DEVICE_VENDOR := ZBT
|
||||
|
|
|
|||
Loading…
Reference in New Issue