ar71xx: add support for AR9331 based Hak5 devices

This adds support for AR9331 based Hak5 penetration testing tools:

- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel

WiFi Pineapple NANO specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button

LAN Turtle specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)

Packet Squirrel specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch

Flash instructions for all 3 devices:

Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.

Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

target/linux/ar71xx/base-files/etc/board.d/01_leds

@@ -405,6 +405,9 @@ hornet-ub-x2)
 	ucidef_set_led_wlan "wlan" "WLAN" "alfa:blue:wlan" "phy0tpt"
 	ucidef_set_led_usbdev "usb" "USB" "alfa:blue:usb" "1-1"
 	;;
+lan-turtle)
+	ucidef_set_led_netdev "wan" "WAN" "$board:orange:system" "eth1"
+	;;
 mc-mac1200r)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "mercury:green:wlan2g" "phy1tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "mercury:green:wlan5g" "phy0tpt"
@@ -951,6 +954,9 @@ whr-hp-gn)
 	ucidef_set_led_switch "lan3" "LAN3" "buffalo:green:lan3" "switch0" "0x08"
 	ucidef_set_led_switch "lan4" "LAN4" "buffalo:green:lan4" "switch0" "0x10"
 	;;
+wifi-pineapple-nano)
+	ucidef_set_led_wlan "wlan0" "WLAN0" "$board:blue:system" "phy0tpt"
+	;;
 wlae-ag300n)
 	ucidef_set_led_netdev "wireless" "WIRELESS" "buffalo:green:wireless" "wlan0"
 	;;

target/linux/ar71xx/base-files/etc/board.d/02_network

@@ -140,6 +140,7 @@ ar71xx_setup_interfaces()
 	unifi|\
 	unifiac-lite|\
 	wi2a-ac200i|\
+	wifi-pineapple-nano|\
 	wndap360|\
 	wp543)
 		ucidef_set_interface_lan "eth0"

target/linux/ar71xx/base-files/etc/diag.sh

@@ -27,6 +27,7 @@ get_status_led() {
 	e600gac-v2|\
 	eap120|\
 	minibox-v1|\
+	packet-squirrel|\
 	som9331|\
 	sr3200|\
 	tl-wr802n-v2|\
@@ -203,7 +204,8 @@ get_status_led() {
 	r36a)
 		status_led="$board:blue:status"
 		;;
-	e600g-v2)
+	e600g-v2|\
+	wifi-pineapple-nano)
 		status_led="$board:blue:system"
 		;;
 	eap300v2)
@@ -254,6 +256,9 @@ get_status_led() {
 	jwap230)
 		status_led="$board:green:led1"
 		;;
+	lan-turtle)
+		status_led="$board:orange:system"
+		;;
 	ls-sr71)
 		status_led="ubnt:green:d22"
 		;;

target/linux/ar71xx/base-files/lib/ar71xx.sh

@@ -741,6 +741,9 @@ ar71xx_board_detect() {
 	*"JWAP230")
 		name="jwap230"
 		;;
+	*"LAN Turtle")
+		name="lan-turtle"
+		;;
 	*"Lima"*)
 		name="lima"
 		;;
@@ -865,6 +868,9 @@ ar71xx_board_detect() {
 	*"Oolite V1.0")
 		name="oolite"
 		;;
+	*"Packet Squirrel")
+		name="packet-squirrel"
+		;;
 	*"PB42")
 		name="pb42"
 		;;
@@ -1327,6 +1333,9 @@ ar71xx_board_detect() {
 	*"WHR-HP-GN")
 		name="whr-hp-gn"
 		;;
+	*"WiFi Pineapple NANO")
+		name="wifi-pineapple-nano"
+		;;
 	*"WLAE-AG300N")
 		name="wlae-ag300n"
 		;;

target/linux/ar71xx/base-files/lib/upgrade/platform.sh

@@ -392,12 +392,14 @@ platform_check_image() {
 	el-m150|\
 	el-mini|\
 	gl-inet|\
+	lan-turtle|\
 	mc-mac1200r|\
 	minibox-v1|\
 	omy-g1|\
 	omy-x1|\
 	onion-omega|\
 	oolite|\
+	packet-squirrel|\
 	re355|\
 	re450|\
 	rut900|\
@@ -466,7 +468,8 @@ platform_check_image() {
 	tl-wr940n-v4|\
 	tl-wr941nd|\
 	tl-wr941nd-v5|\
-	tl-wr941nd-v6)
+	tl-wr941nd-v6|\
+	wifi-pineapple-nano)
 		local magic_ver="0100"
 
 		case "$board" in

target/linux/ar71xx/config-4.4

@@ -131,6 +131,7 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_JA76PF is not set
 # CONFIG_ATH79_MACH_JWAP003 is not set
 # CONFIG_ATH79_MACH_JWAP230 is not set
+# CONFIG_ATH79_MACH_LAN_TURTLE is not set
 # CONFIG_ATH79_MACH_LIMA is not set
 # CONFIG_ATH79_MACH_MC_MAC1200R is not set
 # CONFIG_ATH79_MACH_MR12 is not set
@@ -239,6 +240,7 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_WEIO is not set
 # CONFIG_ATH79_MACH_WHR_HP_G300N is not set
 # CONFIG_ATH79_MACH_WI2A_AC200I is not set
+# CONFIG_ATH79_MACH_WIFI_PINEAPPLE_NANO is not set
 # CONFIG_ATH79_MACH_WLAE_AG300N is not set
 # CONFIG_ATH79_MACH_WLR8100 is not set
 # CONFIG_ATH79_MACH_WNDAP360 is not set

target/linux/ar71xx/config-4.9

@@ -129,6 +129,7 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_JA76PF is not set
 # CONFIG_ATH79_MACH_JWAP003 is not set
 # CONFIG_ATH79_MACH_JWAP230 is not set
+# CONFIG_ATH79_MACH_LAN_TURTLE is not set
 # CONFIG_ATH79_MACH_LIMA is not set
 # CONFIG_ATH79_MACH_MC_MAC1200R is not set
 # CONFIG_ATH79_MACH_MR12 is not set
@@ -237,6 +238,7 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_WEIO is not set
 # CONFIG_ATH79_MACH_WHR_HP_G300N is not set
 # CONFIG_ATH79_MACH_WI2A_AC200I is not set
+# CONFIG_ATH79_MACH_WIFI_PINEAPPLE_NANO is not set
 # CONFIG_ATH79_MACH_WLAE_AG300N is not set
 # CONFIG_ATH79_MACH_WLR8100 is not set
 # CONFIG_ATH79_MACH_WNDAP360 is not set

target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt

@@ -958,6 +958,16 @@ config ATH79_MACH_WAM250
 	select ATH79_DEV_USB
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_WIFI_PINEAPPLE_NANO
+	bool "Hak5 WiFi Pineapple NANO support"
+	select SOC_AR933X
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_WRT160NL
 	bool "Linksys WRT160NL board support"
 	select SOC_AR913X
@@ -2154,6 +2164,15 @@ config ATH79_MACH_CARAMBOLA2
 	select ATH79_DEV_USB
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_LAN_TURTLE
+	bool "Hak5 LAN Turtle and Packet Squirrel support"
+	select SOC_AR933X
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+
 config ATH79_MACH_LIMA
 	bool "8devices Lima board"
 	select SOC_QCA953X

target/linux/ar71xx/files/arch/mips/ath79/Makefile

@@ -139,6 +139,7 @@ obj-$(CONFIG_ATH79_MACH_HORNET_UB)		+= mach-hornet-ub.o
 obj-$(CONFIG_ATH79_MACH_JA76PF)			+= mach-ja76pf.o
 obj-$(CONFIG_ATH79_MACH_JWAP003)		+= mach-jwap003.o
 obj-$(CONFIG_ATH79_MACH_JWAP230)		+= mach-jwap230.o
+obj-$(CONFIG_ATH79_MACH_LAN_TURTLE)		+= mach-lan-turtle.o
 obj-$(CONFIG_ATH79_MACH_LIMA)			+= mach-lima.o
 obj-$(CONFIG_ATH79_MACH_MC_MAC1200R)		+= mach-mc-mac1200r.o
 obj-$(CONFIG_ATH79_MACH_MR12)			+= mach-mr12.o
@@ -246,6 +247,7 @@ obj-$(CONFIG_ATH79_MACH_UBNT_XM)		+= mach-ubnt-xm.o
 obj-$(CONFIG_ATH79_MACH_WAM250)			+= mach-wam250.o
 obj-$(CONFIG_ATH79_MACH_WEIO)			+= mach-weio.o
 obj-$(CONFIG_ATH79_MACH_WHR_HP_G300N)		+= mach-whr-hp-g300n.o
+obj-$(CONFIG_ATH79_MACH_WIFI_PINEAPPLE_NANO)	+= mach-wifi-pineapple-nano.o
 obj-$(CONFIG_ATH79_MACH_WLAE_AG300N)		+= mach-wlae-ag300n.o
 obj-$(CONFIG_ATH79_MACH_WLR8100)		+= mach-wlr8100.o
 obj-$(CONFIG_ATH79_MACH_WNDAP360)		+= mach-wndap360.o

target/linux/ar71xx/files/arch/mips/ath79/mach-lan-turtle.c

@@ -0,0 +1,178 @@
+/*
+ *  Hak5 LAN Turtle and Packet Squirrel boards support
+ *
+ *  Copyright (C) 2018 Sebastian Kinne <seb@hak5.org>
+ *  Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "machtypes.h"
+
+#define LAN_TURTLE_GPIO_BTN_RESET	11
+#define LAN_TURTLE_GPIO_LED_SYS		13
+
+#define PACKET_SQUIRREL_GPIO_BTN_SW1	18
+#define PACKET_SQUIRREL_GPIO_BTN_SW2	20
+#define PACKET_SQUIRREL_GPIO_BTN_SW3	21
+#define PACKET_SQUIRREL_GPIO_BTN_SW4	24
+#define PACKET_SQUIRREL_GPIO_BTN_RESET	11
+#define PACKET_SQUIRREL_GPIO_LED_B	23
+#define PACKET_SQUIRREL_GPIO_LED_G	22
+#define PACKET_SQUIRREL_GPIO_LED_R	19
+
+#define HAK5_KEYS_POLL_INTERVAL		20 /* msecs */
+#define HAK5_KEYS_DEBOUNCE_INTERVAL	(3 * HAK5_KEYS_POLL_INTERVAL)
+
+static const char *hak5_part_probes[] = {
+	"tp-link",
+	NULL,
+};
+
+static struct flash_platform_data hak5_flash_data = {
+	.part_probes = hak5_part_probes,
+};
+
+/* LAN Turtle */
+static struct gpio_led lan_turtle_leds_gpio[] __initdata = {
+	{
+		.name		= "lan-turtle:orange:system",
+		.gpio		= LAN_TURTLE_GPIO_LED_SYS,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button lan_turtle_gpio_keys[] __initdata = {
+	{
+		.desc			= "reset",
+		.type			= EV_KEY,
+		.code			= KEY_RESTART,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= LAN_TURTLE_GPIO_BTN_RESET,
+		.active_low		= 1,
+	},
+};
+
+/* Packet Squirrel */
+static struct gpio_led packet_squirrel_leds_gpio[] __initdata = {
+	{
+		.name		= "packet-squirrel:blue:system",
+		.gpio		= PACKET_SQUIRREL_GPIO_LED_B,
+		.active_low	= 1,
+	}, {
+		.name		= "packet-squirrel:green:system",
+		.gpio		= PACKET_SQUIRREL_GPIO_LED_G,
+		.active_low	= 1,
+	}, {
+		.name		= "packet-squirrel:red:system",
+		.gpio		= PACKET_SQUIRREL_GPIO_LED_R,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button packet_squirrel_gpio_keys[] __initdata = {
+	{
+		.desc			= "reset",
+		.type			= EV_KEY,
+		.code			= KEY_RESTART,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= PACKET_SQUIRREL_GPIO_BTN_RESET,
+		.active_low		= 1,
+	}, {
+		.desc			= "sw1",
+		.type			= EV_KEY,
+		.code			= BTN_0,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= PACKET_SQUIRREL_GPIO_BTN_SW1,
+		.active_low		= 1,
+	}, {
+		.desc			= "sw2",
+		.type			= EV_KEY,
+		.code			= BTN_1,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= PACKET_SQUIRREL_GPIO_BTN_SW2,
+		.active_low		= 1,
+	}, {
+		.desc			= "sw3",
+		.type			= EV_KEY,
+		.code			= BTN_2,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= PACKET_SQUIRREL_GPIO_BTN_SW3,
+		.active_low		= 1,
+	}, {
+		.desc			= "sw4",
+		.type			= EV_KEY,
+		.code			= BTN_3,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= PACKET_SQUIRREL_GPIO_BTN_SW4,
+		.active_low		= 1,
+	},
+};
+
+static void __init hak5_common_setup(void)
+{
+	u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00);
+
+	ath79_register_m25p80(&hak5_flash_data);
+
+	ath79_register_mdio(0, 0x0);
+
+	ath79_switch_data.phy_poll_mask = 0xfe;
+
+	ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
+	ath79_register_eth(0);
+
+	ath79_init_mac(ath79_eth1_data.mac_addr, mac, -1);
+	ath79_register_eth(1);
+
+	ath79_register_usb();
+
+	/* GPIO11/12 */
+	ath79_gpio_function_disable(AR933X_GPIO_FUNC_UART_RTS_CTS_EN);
+}
+
+static void __init lan_turtle_setup(void)
+{
+	hak5_common_setup();
+
+	/* GPIO13 */
+	ath79_gpio_function_disable(AR933X_GPIO_FUNC_ETH_SWITCH_LED0_EN);
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(lan_turtle_leds_gpio),
+				 lan_turtle_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, HAK5_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(lan_turtle_gpio_keys),
+					lan_turtle_gpio_keys);
+}
+
+static void __init packet_squirrel_setup(void)
+{
+	hak5_common_setup();
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(packet_squirrel_leds_gpio),
+				 packet_squirrel_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, HAK5_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(packet_squirrel_gpio_keys),
+					packet_squirrel_gpio_keys);
+}
+
+MIPS_MACHINE(ATH79_MACH_LAN_TURTLE, "LAN-TURTLE",
+	     "Hak5 LAN Turtle", lan_turtle_setup);
+
+MIPS_MACHINE(ATH79_MACH_PACKET_SQUIRREL, "PACKET-SQUIRREL",
+	     "Hak5 Packet Squirrel", packet_squirrel_setup);

target/linux/ar71xx/files/arch/mips/ath79/mach-wifi-pineapple-nano.c

@@ -0,0 +1,107 @@
+/*
+ *  Hak5 WiFi Pineapple NANO board support
+ *
+ *  Copyright (C) 2018 Sebastian Kinne <seb@hak5.org>
+ *  Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define WIFI_PINEAPPLE_NANO_GPIO_LED_SYSTEM	18
+
+#define WIFI_PINEAPPLE_NANO_GPIO_BTN_RESET	12
+#define WIFI_PINEAPPLE_NANO_GPIO_SD_DET		19
+#define WIFI_PINEAPPLE_NANO_GPIO_USB_ALARM	20
+#define WIFI_PINEAPPLE_NANO_GPIO_USB_POWER	23
+
+#define HAK5_KEYS_POLL_INTERVAL			20 /* msecs */
+#define HAK5_KEYS_DEBOUNCE_INTERVAL		(3 * HAK5_KEYS_POLL_INTERVAL)
+
+#define WIFI_PINEAPPLE_NANO_MAC1_OFFSET		0x0006
+#define WIFI_PINEAPPLE_NANO_CALDATA_OFFSET	0x1000
+
+static const char *hak5_part_probes[] = {
+	"tp-link",
+	NULL,
+};
+
+static struct flash_platform_data hak5_flash_data = {
+	.part_probes = hak5_part_probes,
+};
+
+static struct gpio_led wifi_pineapple_nano_leds_gpio[] __initdata = {
+	{
+		.name		= "wifi-pineapple-nano:blue:system",
+		.gpio		= WIFI_PINEAPPLE_NANO_GPIO_LED_SYSTEM,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button wifi_pineapple_nano_gpio_keys[] __initdata = {
+	{
+		.desc			= "reset",
+		.type			= EV_KEY,
+		.code			= KEY_RESTART,
+		.debounce_interval	= HAK5_KEYS_DEBOUNCE_INTERVAL,
+		.gpio			= WIFI_PINEAPPLE_NANO_GPIO_BTN_RESET,
+		.active_low		= 1,
+	}
+};
+
+static void __init wifi_pineapple_nano_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
+	ath79_register_m25p80(&hak5_flash_data);
+
+	ath79_setup_ar933x_phy4_switch(false, false);
+	ath79_register_mdio(0, 0x0);
+
+	ath79_init_mac(ath79_eth0_data.mac_addr,
+		       art + WIFI_PINEAPPLE_NANO_MAC1_OFFSET, 0);
+	ath79_register_eth(0);
+
+	/* GPIO11/12 */
+	ath79_gpio_function_disable(AR933X_GPIO_FUNC_UART_RTS_CTS_EN);
+
+	gpio_request_one(WIFI_PINEAPPLE_NANO_GPIO_SD_DET,
+			 GPIOF_IN | GPIOF_EXPORT_DIR_FIXED | GPIOF_ACTIVE_LOW,
+			 "SD card present");
+
+	gpio_request_one(WIFI_PINEAPPLE_NANO_GPIO_USB_ALARM,
+			 GPIOF_IN | GPIOF_EXPORT_DIR_FIXED | GPIOF_ACTIVE_LOW,
+			 "USB alarm");
+
+	gpio_request_one(WIFI_PINEAPPLE_NANO_GPIO_USB_POWER,
+			 GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED |
+			 GPIOF_ACTIVE_LOW, "USB power");
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(wifi_pineapple_nano_leds_gpio),
+				 wifi_pineapple_nano_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, HAK5_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(wifi_pineapple_nano_gpio_keys),
+					wifi_pineapple_nano_gpio_keys);
+
+	ath79_register_usb();
+	ath79_register_wmac(art + WIFI_PINEAPPLE_NANO_CALDATA_OFFSET, NULL);
+}
+
+MIPS_MACHINE(ATH79_MACH_WIFI_PINEAPPLE_NANO, "WIFI-PINEAPPLE-NANO",
+	     "Hak5 WiFi Pineapple NANO", wifi_pineapple_nano_setup);

target/linux/ar71xx/files/arch/mips/ath79/machtypes.h

@@ -135,6 +135,7 @@ enum ath79_mach_type {
 	ATH79_MACH_JA76PF2,			/* jjPlus JA76PF2 */
 	ATH79_MACH_JWAP003,			/* jjPlus JWAP003 */
 	ATH79_MACH_JWAP230,			/* jjPlus JWAP230 */
+	ATH79_MACH_LAN_TURTLE,			/* Hak5 LAN Turtle */
 	ATH79_MACH_LIMA,			/* 8devices Lima */
 	ATH79_MACH_MC_MAC1200R,			/* MERCURY MAC1200R */
 	ATH79_MACH_MR12,			/* Cisco Meraki MR12 */
@@ -170,6 +171,7 @@ enum ath79_mach_type {
 	ATH79_MACH_OMY_G1,			/* OMYlink OMY-G1 */
 	ATH79_MACH_OMY_X1,			/* OMYlink OMY-X1 */
 	ATH79_MACH_ONION_OMEGA,			/* ONION OMEGA */
+	ATH79_MACH_PACKET_SQUIRREL,		/* Hak5 Packet Squirrel */
 	ATH79_MACH_PB42,			/* Atheros PB42 */
 	ATH79_MACH_PB44,			/* Atheros PB44 reference board */
 	ATH79_MACH_PQI_AIR_PEN,			/* PQI Air Pen */
@@ -323,6 +325,7 @@ enum ath79_mach_type {
 	ATH79_MACH_WHR_G301N,			/* Buffalo WHR-G301N */
 	ATH79_MACH_WHR_HP_G300N,		/* Buffalo WHR-HP-G300N */
 	ATH79_MACH_WHR_HP_GN,			/* Buffalo WHR-HP-GN */
+	ATH79_MACH_WIFI_PINEAPPLE_NANO,		/* Hak5 WiFi Pineapple NANO */
 	ATH79_MACH_WLAE_AG300N,			/* Buffalo WLAE-AG300N */
 	ATH79_MACH_WLR8100,			/* SITECOM WLR-8100 */
 	ATH79_MACH_WNDAP360,			/* NETGEAR WNDAP360 */

target/linux/ar71xx/generic/config-default

@@ -101,6 +101,7 @@ CONFIG_ATH79_MACH_HORNET_UB=y
 CONFIG_ATH79_MACH_JA76PF=y
 CONFIG_ATH79_MACH_JWAP003=y
 CONFIG_ATH79_MACH_JWAP230=y
+CONFIG_ATH79_MACH_LAN_TURTLE=y
 CONFIG_ATH79_MACH_LIMA=y
 CONFIG_ATH79_MACH_MC_MAC1200R=y
 CONFIG_ATH79_MACH_MR12=y
@@ -169,6 +170,7 @@ CONFIG_ATH79_MACH_UBNT_XM=y
 CONFIG_ATH79_MACH_WAM250=y
 CONFIG_ATH79_MACH_WEIO=y
 CONFIG_ATH79_MACH_WHR_HP_G300N=y
+CONFIG_ATH79_MACH_WIFI_PINEAPPLE_NANO=y
 CONFIG_ATH79_MACH_WLAE_AG300N=y
 CONFIG_ATH79_MACH_WLR8100=y
 CONFIG_ATH79_MACH_WNDAP360=y

target/linux/ar71xx/image/generic.mk

@@ -484,6 +484,19 @@ define Device/gl-usb150
 endef
 TARGET_DEVICES += gl-usb150
 
+define Device/lan-turtle
+  $(Device/tplink-16mlzma)
+  DEVICE_TITLE := Hak5 LAN Turtle
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage \
+	-kmod-ath9k -swconfig -uboot-envtools -wpad-mini
+  BOARDNAME := LAN-TURTLE
+  DEVICE_PROFILE := LANTURTLE
+  TPLINK_HWID := 0x5348334c
+  CONSOLE := ttyATH0,115200
+  IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += lan-turtle
+
 define Device/lima
   DEVICE_TITLE := 8devices Lima
   DEVICE_PACKAGES := kmod-usb-core kmod-usb2
@@ -656,6 +669,19 @@ define Device/cr5000-nocloud
 endef
 TARGET_DEVICES += cr5000-nocloud
 
+define Device/packet-squirrel
+  $(Device/tplink-16mlzma)
+  DEVICE_TITLE := Hak5 Packet Squirrel
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 \
+	-kmod-ath9k -swconfig -uboot-envtools -wpad-mini
+  BOARDNAME := PACKET-SQUIRREL
+  DEVICE_PROFILE := PACKETSQUIRREL
+  TPLINK_HWID := 0x5351524c
+  CONSOLE := ttyATH0,115200
+  IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += packet-squirrel
+
 define Device/pqi-air-pen
   DEVICE_TITLE := PQI Air Pen
   DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage
@@ -1125,6 +1151,19 @@ define Device/wam250
 endef
 TARGET_DEVICES += wam250
 
+define Device/wifi-pineapple-nano
+  $(Device/tplink-16mlzma)
+  DEVICE_TITLE := Hak5 WiFi Pineapple NANO
+  DEVICE_PACKAGES := kmod-ath9k-htc kmod-usb-core kmod-usb2 kmod-usb-storage \
+	-swconfig -uboot-envtools
+  BOARDNAME := WIFI-PINEAPPLE-NANO
+  DEVICE_PROFILE := WIFIPINEAPPLENANO
+  TPLINK_HWID := 0x4e414e4f
+  CONSOLE := ttyATH0,115200
+  IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += wifi-pineapple-nano
+
 define Device/wlr8100
   DEVICE_TITLE := Sitecom WLR-8100
   DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-usb3 \