mirror of https://github.com/hak5/openwrt.git
ath79: add support for ALFA Network N2Q
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros QCA9531 v2. This model is a successor of the old N2 which was based on Atheros AR7240. FCC ID: 2AB8795311. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA - 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V) - PoE pass through in second port (controlled by GPIO) - support for optional 802.3af/at PoE module - 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards) - 2x IPEX/U.FL connectors on PCB - 1x USB 2.0 mini Type-B (power controlled by GPIO) - 8x LED (7 of them are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - UART (4-pin, 2.54 mm pitch) header on PCB - LEDs (2x 5-pin, 2.54 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>master
Piotr Dymacz
parent
9181b039f3
commit
6492ea7d9e
|
|
@ -0,0 +1,120 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9531_alfa-network_r36a.dtsi"
|
||||
|
||||
/ {
|
||||
model = "ALFA Network N2Q";
|
||||
compatible = "alfa-network,n2q", "qca,qca9531";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_usb;
|
||||
led-failsafe = &led_usb;
|
||||
led-upgrade = &led_usb;
|
||||
};
|
||||
|
||||
gpio-export-pcf8574 {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
poe-passthrough {
|
||||
gpio-export,name = "poe-passthrough";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&pcf8574 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb-power {
|
||||
gpio-export,name = "usb-power";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&pcf8574 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c {
|
||||
compatible = "i2c-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
sda-gpios = <&gpio 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
||||
|
||||
pcf8574: pcf8574@20 {
|
||||
compatible = "nxp,pcf8574";
|
||||
reg = <0x20>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&enable_gpio4 &enable_gpio16>;
|
||||
|
||||
lan1 {
|
||||
label = "n2q:orange:lan1";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan2 {
|
||||
label = "n2q:orange:lan2";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_usb: usb {
|
||||
label = "n2q:green:usb";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port0>;
|
||||
};
|
||||
|
||||
minipcie {
|
||||
label = "n2q:green:minipcie";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "n2q:green:wlan";
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
leds-pcf8574 {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
poe-passthrough {
|
||||
label = "n2q:green:poe-passthrough";
|
||||
gpios = <&pcf8574 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal1 {
|
||||
label = "n2q:red:signal1";
|
||||
gpios = <&pcf8574 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal2 {
|
||||
label = "n2q:orange:signal2";
|
||||
gpios = <&pcf8574 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
signal3 {
|
||||
label = "n2q:green:signal3";
|
||||
gpios = <&pcf8574 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
mtd-mac-address = <&art 0x1002>;
|
||||
mtd-mac-address-increment = <(-2)>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
mtd-mac-address = <&art 0x1002>;
|
||||
mtd-mac-address-increment = <(-1)>;
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
@ -1,57 +1,18 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include "qca9531_alfa-network_r36a.dtsi"
|
||||
|
||||
/ {
|
||||
model = "ALFA Network R36A";
|
||||
compatible = "alfa-network,r36a", "qca,qca9531";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &wmac;
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usb-power {
|
||||
gpio-export,name = "usb-power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
watchdog-enable {
|
||||
gpio-export,name = "watchdog-enable";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
|
|
@ -86,20 +47,9 @@
|
|||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <25000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
};
|
||||
|
||||
|
|
@ -111,80 +61,19 @@
|
|||
mtd-mac-address = <&art 0x6>;
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
enable_gpio4: pinmux_enable_gpio4 {
|
||||
pinctrl-single,bits = <0x04 0x0 0xff>;
|
||||
};
|
||||
|
||||
enable_gpio16: pinmux_enable_gpio16 {
|
||||
pinctrl-single,bits = <0x10 0x0 0xff>;
|
||||
&gpio_export {
|
||||
usb-power {
|
||||
gpio-export,name = "usb-power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <50000000>;
|
||||
m25p,fast-read;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x060000 0x010000>;
|
||||
};
|
||||
|
||||
art: partition@70000 {
|
||||
label = "art";
|
||||
reg = <0x070000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x080000 0xf80000>;
|
||||
};
|
||||
};
|
||||
&keys {
|
||||
rfkill {
|
||||
label = "rfkill";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port0: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
|
|
|||
|
|
@ -0,0 +1,126 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
label-mac-device = &wmac;
|
||||
};
|
||||
|
||||
gpio_export: gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
watchdog-enable {
|
||||
gpio-export,name = "watchdog-enable";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys: keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <25000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
enable_gpio4: pinmux_enable_gpio4 {
|
||||
pinctrl-single,bits = <0x04 0x0 0xff>;
|
||||
};
|
||||
|
||||
enable_gpio16: pinmux_enable_gpio16 {
|
||||
pinctrl-single,bits = <0x10 0x0 0xff>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <50000000>;
|
||||
m25p,fast-read;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x060000 0x010000>;
|
||||
};
|
||||
|
||||
art: partition@70000 {
|
||||
label = "art";
|
||||
reg = <0x070000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x080000 0xf80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port0: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
};
|
||||
|
|
@ -17,6 +17,14 @@ alfa-network,ap121fe|\
|
|||
avm,fritz450e)
|
||||
ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
|
||||
;;
|
||||
alfa-network,n2q)
|
||||
ucidef_set_led_netdev "lan2" "LAN2" "$boardname:orange:lan2" "eth1"
|
||||
ucidef_set_led_switch "lan1" "LAN1" "$boardname:orange:lan1" "switch0" "0x10"
|
||||
ucidef_set_rssimon "wlan0" "200000" "1"
|
||||
ucidef_set_led_rssi "signal1" "SIGNAL1" "$boardname:red:signal1" "wlan0" "1" "100"
|
||||
ucidef_set_led_rssi "signal2" "SIGNAL2" "$boardname:orange:signal2" "wlan0" "33" "100"
|
||||
ucidef_set_led_rssi "signal3" "SIGNAL3" "$boardname:green:signal3" "wlan0" "66" "100"
|
||||
;;
|
||||
alfa-network,r36a)
|
||||
ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0"
|
||||
ucidef_set_led_switch "wan" "WAN" "$boardname:blue:wan" "switch0" "0x10"
|
||||
|
|
|
|||
|
|
@ -78,6 +78,12 @@ ath79_setup_interfaces()
|
|||
alfa-network,ap121fe)
|
||||
ucidef_set_interface_lan "eth0 usb0"
|
||||
;;
|
||||
alfa-network,n2q|\
|
||||
devolo,dvl1200e|\
|
||||
devolo,dvl1750e|\
|
||||
ocedo,ursus)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
avm,fritz4020|\
|
||||
pcs,cr3000|\
|
||||
tplink,archer-c58-v1|\
|
||||
|
|
@ -147,11 +153,6 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan" "2:wan"
|
||||
;;
|
||||
devolo,dvl1200e|\
|
||||
devolo,dvl1750e|\
|
||||
ocedo,ursus)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
devolo,magic-2-wifi)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:wan" "3:lan" "4:lan"
|
||||
|
|
@ -402,6 +403,7 @@ ath79_setup_macs()
|
|||
;;
|
||||
alfa-network,ap121f|\
|
||||
alfa-network,ap121fe|\
|
||||
alfa-network,n2q|\
|
||||
alfa-network,r36a|\
|
||||
engenius,ens202ext-v1)
|
||||
label_mac=$(mtd_get_mac_binary art 0x1002)
|
||||
|
|
|
|||
|
|
@ -237,6 +237,16 @@ define Device/alfa-network_ap121fe
|
|||
endef
|
||||
TARGET_DEVICES += alfa-network_ap121fe
|
||||
|
||||
define Device/alfa-network_n2q
|
||||
SOC := qca9531
|
||||
DEVICE_VENDOR := ALFA Network
|
||||
DEVICE_MODEL := N2Q
|
||||
DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
|
||||
kmod-usb-ledtrig-usbport rssileds
|
||||
IMAGE_SIZE := 15872k
|
||||
endef
|
||||
TARGET_DEVICES += alfa-network_n2q
|
||||
|
||||
define Device/alfa-network_r36a
|
||||
SOC := qca9531
|
||||
DEVICE_VENDOR := ALFA Network
|
||||
|
|
|
|||
Loading…
Reference in New Issue