mirror of https://github.com/hak5/openwrt.git
kirkwood: add ZyXEL NSA325 device
This patch add ZyXEL NSA325 2-Bay Media Server The ZyXEL NSA325 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1600Mhz - SDRAM memory: 512MB DDR2 400Mhz - Gigabit ethernet: Marvell Alaska - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II ports (internal) - 2 USB 2.0 ports (back) - 1 USB 3.0 port (front) - Fan (fixed speed) - hardware watchdog in a mcu Basically a bigger, more powerful version of NSA310, installation is the same as they share the same flash layout. A notable difference is that there is a hardware watchdog in a mcu on the board, which is disabled by default in the LEDE u-boot. The watchdog is also disabled with a GPIO activation through raw register change when kwbooting or it would reset the board before the new uboot was transferred. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]openwrt-18.06
Alberto Bursi
Felix Fietkau
parent
add1dd0081
commit
4383c13aee
|
|
@ -41,6 +41,9 @@ case "$board" in
|
|||
"nsa310b")
|
||||
ucidef_set_led_default "health" "health" "nsa310:green:sys" "1"
|
||||
;;
|
||||
"nsa325")
|
||||
ucidef_set_led_default "health" "health" "nsa325:green:sys" "1"
|
||||
;;
|
||||
"sheevaplug" | \
|
||||
"sheevaplug-esata")
|
||||
ucidef_set_led_timer "health" "health" "sheevaplug:blue:health" "200" "800"
|
||||
|
|
|
|||
|
|
@ -30,7 +30,7 @@ case "$board" in
|
|||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0" "6@eth1"
|
||||
;;
|
||||
"nsa310b")
|
||||
"nsa310b"|"nsa325")
|
||||
ucidef_set_interface_lan "eth0" "dhcp"
|
||||
ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr )
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -65,6 +65,10 @@ kirkwood_board_detect() {
|
|||
name="nsa310s"
|
||||
;;
|
||||
|
||||
"ZyXEL NSA325")
|
||||
name="nsa325"
|
||||
;;
|
||||
|
||||
*)
|
||||
name="generic"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -11,7 +11,7 @@ include $(TOPDIR)/rules.mk
|
|||
include $(INCLUDE_DIR)/image.mk
|
||||
|
||||
KERNEL_LOADADDR:=0x8000
|
||||
TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b
|
||||
TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b nsa325
|
||||
|
||||
UBI_OPTS := -m 2048 -p 128KiB -s 512
|
||||
UBIFS_OPTS := -m 2048 -e 126KiB -c 4096
|
||||
|
|
@ -87,6 +87,13 @@ $(Device/dockstar)
|
|||
DEVICE_PACKAGES := kmod-r8169 kmod-gpio-button-hotplug kmod-hwmon-lm85
|
||||
endef
|
||||
|
||||
define Device/nsa325
|
||||
$(Device/dockstar)
|
||||
DEVICE_TITLE := ZyXEL NSA325 (v1 and v2)
|
||||
DEVICE_DTS := kirkwood-nsa325
|
||||
DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
|
||||
endef
|
||||
|
||||
define Device/pogo_e02
|
||||
$(Device/dockstar)
|
||||
DEVICE_TITLE := Cloud Engines Pogoplug E02
|
||||
|
|
|
|||
|
|
@ -0,0 +1,238 @@
|
|||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -205,6 +205,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
|
||||
kirkwood-nsa310a.dtb \
|
||||
kirkwood-nsa310b.dtb \
|
||||
kirkwood-nsa310s.dtb \
|
||||
+ kirkwood-nsa325.dtb \
|
||||
kirkwood-openblocks_a6.dtb \
|
||||
kirkwood-openblocks_a7.dtb \
|
||||
kirkwood-openrd-base.dtb \
|
||||
--- /dev/null
|
||||
+++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
|
||||
@@ -0,0 +1,225 @@
|
||||
+/*
|
||||
+ * Device tree file for Zyxel NSA325 and NSA325v2 NAS
|
||||
+ */
|
||||
+/dts-v1/;
|
||||
+#include "kirkwood-nsa3x0-common.dtsi"
|
||||
+
|
||||
+/ {
|
||||
+ model = "ZyXEL NSA325";
|
||||
+ compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
|
||||
+
|
||||
+ memory {
|
||||
+ device_type = "memory";
|
||||
+ reg = <0x00000000 0x20000000>;
|
||||
+ };
|
||||
+
|
||||
+ chosen {
|
||||
+ bootargs = "console=ttyS0,115200";
|
||||
+ stdout-path = &uart0;
|
||||
+ };
|
||||
+
|
||||
+ mbus {
|
||||
+ pcie-controller {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ pcie@1,0 {
|
||||
+ status = "okay";
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ ocp@f1000000 {
|
||||
+ pinctrl: pin-controller@10000 {
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ pmx_led_sata2_green: pmx-led-sata2-green {
|
||||
+ marvell,pins = "mpp12";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_sata2_red: pmx-led-sata2-red {
|
||||
+ marvell,pins = "mpp13";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_mcu_data: pmx-mcu-data {
|
||||
+ marvell,pins = "mpp14";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_usb_green: pmx-led-usb-green {
|
||||
+ marvell,pins = "mpp15";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_mcu_clk: pmx-mcu-clk {
|
||||
+ marvell,pins = "mpp16";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_mcu_act: pmx-mcu-act {
|
||||
+ marvell,pins = "mpp17";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_usb_power_off: pmx-usb-power-off {
|
||||
+ marvell,pins = "mpp21";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_sys_green: pmx-led-sys-green {
|
||||
+ marvell,pins = "mpp28";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_sys_orange: pmx-led-sys-orange {
|
||||
+ marvell,pins = "mpp29";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_sata1_green: pmx-led-sata1-green {
|
||||
+ marvell,pins = "mpp41";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led_sata1_red: pmx-led-sata1-red {
|
||||
+ marvell,pins = "mpp42";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_beeper: pmx-beeper {
|
||||
+ marvell,pins = "mpp44";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_pwr_sata1: pmx-pwr-sata1 {
|
||||
+ marvell,pins = "mpp47";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ };
|
||||
+
|
||||
+ /* This board uses the pcf8563 RTC instead of the SoC RTC */
|
||||
+ rtc@10300 {
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+
|
||||
+ i2c@11000 {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ pcf8563: pcf8563@51 {
|
||||
+ compatible = "nxp,pcf8563";
|
||||
+ reg = <0x51>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ };
|
||||
+
|
||||
+ gpio-leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&pmx_led_sata1_green &pmx_led_sata1_red
|
||||
+ &pmx_led_sata2_green &pmx_led_sata2_red
|
||||
+ &pmx_led_sys_green &pmx_led_sys_orange
|
||||
+ &pmx_led_copy_green &pmx_led_copy_red
|
||||
+ &pmx_led_usb_green>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ green-sata2 {
|
||||
+ label = "nsa325:green:sata2";
|
||||
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
+ linux,default-trigger = "ide-disk2";
|
||||
+ };
|
||||
+
|
||||
+ red-sata2 {
|
||||
+ label = "nsa325:red:sata2";
|
||||
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+
|
||||
+ green-usb {
|
||||
+ label = "nsa325:green:usb";
|
||||
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
|
||||
+ linux,default-trigger = "usb-host";
|
||||
+ };
|
||||
+
|
||||
+ green-sys {
|
||||
+ label = "nsa325:green:sys";
|
||||
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
|
||||
+ linux,default-trigger = "default-on";
|
||||
+ };
|
||||
+
|
||||
+ orange-sys {
|
||||
+ label = "nsa325:orange:sys";
|
||||
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
|
||||
+ linux,default-trigger = "cpu0";
|
||||
+ };
|
||||
+
|
||||
+ green-copy {
|
||||
+ label = "nsa325:green:copy";
|
||||
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+
|
||||
+ red-copy {
|
||||
+ label = "nsa325:red:copy";
|
||||
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+
|
||||
+ green-sata1 {
|
||||
+ label = "nsa325:green:sata1";
|
||||
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
|
||||
+ linux,default-trigger = "ide-disk1";
|
||||
+ };
|
||||
+
|
||||
+ red-sata1 {
|
||||
+ label = "nsa325:red:sata1";
|
||||
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ regulators {
|
||||
+ compatible = "simple-bus";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ pinctrl-0 = <&pmx_usb_power_off &pmx_pwr_sata1>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ usb_power: regulator@1 {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ reg = <1>;
|
||||
+ regulator-name = "USB Power";
|
||||
+ regulator-min-microvolt = <5000000>;
|
||||
+ regulator-max-microvolt = <5000000>;
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ enable-active-high;
|
||||
+ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+
|
||||
+ sata1_power: regulator@2 {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ reg = <2>;
|
||||
+ regulator-name = "SATA Power";
|
||||
+ regulator-min-microvolt = <5000000>;
|
||||
+ regulator-max-microvolt = <5000000>;
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ enable-active-high;
|
||||
+ gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&mdio {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ ethphy0: ethernet-phy@1 {
|
||||
+ reg = <1>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+ð0 {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ ethernet0-port@0 {
|
||||
+ phy-handle = <ðphy0>;
|
||||
+ };
|
||||
+};
|
||||
Loading…
Reference in New Issue