mirror of https://github.com/hak5/openwrt.git
ramips: add support for I-O DATA WN-DX1167R
I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : NAND 128 MiB - WLAN : MediaTek MT7615D (2.4/5 GHz, 2T2R) - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7621A (MT7530) - LEDs/Input : 2x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J5: Vcc, TX, RX, NC, GND - 57600 bps Flash instruction using initramfs image: 1. Boot WN-DX1167R normally 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt initramfs image and click update ("更新") button to perform firmware update 4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~120 seconds to complete flashing Notes: - configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode for MT7615D chip is not supported in mt76 driver - last 0x80000 (512 KiB) in NAND flash is not used on stock firmware - stock firmware requires "customized uImage header" by MSTC (MitraStar Technology Corp.), but U-Boot doesn't - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC) - header crc32 (0x4 - 0x7) : with data length and data crc32 - image name (0x20 - 0x37) : model ID and firmware versions - data length (0x38 - 0x3b): kernel + rootfs - data crc32 (0x3c - 0x3f) : kernel + rootfs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run>master
INAGAKI Hiroshi
Adrian Schmutzler
parent
be4d53bf69
commit
3c0e2aa63e
|
|
@ -0,0 +1,31 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7621_iodata_wn-xx-xr.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "iodata,wn-dx1167r", "mediatek,mt7621-soc";
|
||||
model = "I-O DATA WN-DX1167R";
|
||||
};
|
||||
|
||||
&partitions {
|
||||
partition@6b00000 {
|
||||
label = "idmkey";
|
||||
reg = <0x6b00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6c00000 {
|
||||
label = "Backup";
|
||||
reg = <0x6c00000 0x1380000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,140 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wps {
|
||||
label = "iodata:green:wps";
|
||||
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power: power {
|
||||
label = "iodata:green:power";
|
||||
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
repeater {
|
||||
label = "repeater";
|
||||
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@200000 {
|
||||
label = "factory";
|
||||
reg = <0x0200000 0x0100000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "SecondBoot";
|
||||
reg = <0x0300000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "kernel";
|
||||
reg = <0x0400000 0x0400000>;
|
||||
};
|
||||
|
||||
partition@800000 {
|
||||
label = "ubi";
|
||||
reg = <0x0800000 0x2e00000>;
|
||||
};
|
||||
|
||||
partition@3600000 {
|
||||
label = "Config";
|
||||
reg = <0x3600000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3700000 {
|
||||
label = "firmware_2";
|
||||
reg = <0x3700000 0x3200000>;
|
||||
};
|
||||
|
||||
partition@6900000 {
|
||||
label = "Config_2";
|
||||
reg = <0x6900000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6a00000 {
|
||||
label = "persist";
|
||||
reg = <0x6a00000 0x0100000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&factory 0xe000>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
ralink,group = "uart2", "uart3", "wdt";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
@ -65,6 +65,22 @@ define Build/iodata-factory
|
|||
fi
|
||||
endef
|
||||
|
||||
define Build/iodata-mstc-header
|
||||
( \
|
||||
data_size_crc="$$(dd if=$@ ibs=64 skip=1 2>/dev/null | \
|
||||
gzip -c | tail -c 8 | od -An -tx8 --endian little | tr -d ' \n')"; \
|
||||
echo -ne "$$(echo $$data_size_crc | sed 's/../\\x&/g')" | \
|
||||
dd of=$@ bs=8 count=1 seek=7 conv=notrunc 2>/dev/null; \
|
||||
)
|
||||
dd if=/dev/zero of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null
|
||||
( \
|
||||
header_crc="$$(dd if=$@ bs=64 count=1 2>/dev/null | \
|
||||
gzip -c | tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
||||
echo -ne "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
||||
dd of=$@ bs=4 count=1 seek=1 conv=notrunc 2>/dev/null; \
|
||||
)
|
||||
endef
|
||||
|
||||
define Build/ubnt-erx-factory-image
|
||||
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
|
||||
echo '21001:6' > $(1).compat; \
|
||||
|
|
@ -336,6 +352,22 @@ define Device/iodata_wn-ax1167gr
|
|||
endef
|
||||
TARGET_DEVICES += iodata_wn-ax1167gr
|
||||
|
||||
define Device/iodata_wn-dx1167r
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
UBINIZE_OPTS := -E 5
|
||||
UIMAGE_MAGIC := 0x434f4d43
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 51200k
|
||||
DEVICE_VENDOR := I-O DATA
|
||||
DEVICE_MODEL := WN-DX1167R
|
||||
KERNEL_INITRAMFS := $(KERNEL_DTB) | custom-initramfs-uimage 3.10(XIK.1)b10 | \
|
||||
iodata-mstc-header
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := kmod-mt7615e wpad-basic
|
||||
endef
|
||||
TARGET_DEVICES += iodata_wn-dx1167r
|
||||
|
||||
define Device/iodata_wn-gx300gr
|
||||
IMAGE_SIZE := 7616k
|
||||
DEVICE_VENDOR := I-O DATA
|
||||
|
|
|
|||
|
|
@ -72,6 +72,7 @@ ramips_setup_interfaces()
|
|||
elecom,wrc-1900gst|\
|
||||
elecom,wrc-2533gst|\
|
||||
iodata,wn-ax1167gr|\
|
||||
iodata,wn-dx1167r|\
|
||||
iodata,wn-gx300gr|\
|
||||
iodata,wnpr2600g|\
|
||||
iptime,a8004t)
|
||||
|
|
@ -222,6 +223,11 @@ ramips_setup_macs()
|
|||
xiaoyu,xy-c5)
|
||||
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1)
|
||||
;;
|
||||
iodata,wn-dx1167r|\
|
||||
xiaomi,mir3g-v2)
|
||||
wan_mac=$(mtd_get_mac_binary factory 0xe006)
|
||||
label_mac=$wan_mac
|
||||
;;
|
||||
iodata,wnpr2600g)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
||||
label_mac=$wan_mac
|
||||
|
|
@ -266,10 +272,6 @@ ramips_setup_macs()
|
|||
lan_mac=$(mtd_get_mac_binary factory 0xe006)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
xiaomi,mir3g-v2)
|
||||
wan_mac=$(mtd_get_mac_binary factory 0xe006)
|
||||
label_mac=$wan_mac
|
||||
;;
|
||||
zbtlink,zbt-we1326)
|
||||
wan_mac=$(mtd_get_mac_binary factory 0xe006)
|
||||
label_mac=$(mtd_get_mac_binary factory 0x4)
|
||||
|
|
|
|||
|
|
@ -0,0 +1,55 @@
|
|||
#
|
||||
# Copyright (C) 2019 OpenWrt.org
|
||||
#
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
iodata_mstc_prepare_fail() {
|
||||
echo "failed to check and prepare the environment, rebooting..."
|
||||
umount -a
|
||||
reboot -f
|
||||
}
|
||||
|
||||
# I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.)
|
||||
# have two important flags:
|
||||
# - bootnum: switch between two os images
|
||||
# use 1st image in OpenWrt
|
||||
# - debugflag: enable/disable debug
|
||||
# users can interrupt Z-Loader for recovering the device if enabled
|
||||
iodata_mstc_upgrade_prepare() {
|
||||
local persist_mtd="$(find_mtd_part persist)"
|
||||
local factory_mtd="$(find_mtd_part factory)"
|
||||
|
||||
if [ -z "$persist_mtd" -o -z "$factory_mtd" ]; then
|
||||
echo 'cannot find mtd partition(s), "factory" or "persist"'
|
||||
iodata_mstc_prepare_fail
|
||||
fi
|
||||
|
||||
local bootnum=$(hexdump -s 4 -n 1 -e '"%x"' ${persist_mtd})
|
||||
local debugflag=$(hexdump -s 65141 -n 1 -e '"%x"' ${factory_mtd})
|
||||
|
||||
if [ "$bootnum" != "1" -a "$bootnum" != "2" ]; then
|
||||
echo "failed to get bootnum, please check the value at 0x4 in ${persist_mtd}"
|
||||
iodata_mstc_prepare_fail
|
||||
fi
|
||||
if [ "$debugflag" != "0" -a "$debugflag" != "1" ]; then
|
||||
echo "failed to get debugflag, please check the value at 0xFE75 in ${factory_mtd}"
|
||||
iodata_mstc_prepare_fail
|
||||
fi
|
||||
echo "current: bootnum => ${bootnum}, debugflag => ${debugflag}"
|
||||
|
||||
if [ "$bootnum" = "2" ]; then
|
||||
if ! (echo -ne "\x01" | dd bs=1 count=1 seek=4 conv=notrunc of=${persist_mtd} 2>/dev/null); then
|
||||
echo "failed to set bootnum"
|
||||
iodata_mstc_prepare_fail
|
||||
fi
|
||||
echo "### switch to 1st os-image on next boot ###"
|
||||
fi
|
||||
if [ "$debugflag" = "0" ]; then
|
||||
if ! (echo -ne "\x01" | dd bs=1 count=1 seek=65141 conv=notrunc of=${factory_mtd} 2>/dev/null); then
|
||||
echo "failed to set debugflag"
|
||||
iodata_mstc_prepare_fail
|
||||
fi
|
||||
echo "### enable debug ###"
|
||||
fi
|
||||
}
|
||||
|
|
@ -53,6 +53,10 @@ platform_do_upgrade() {
|
|||
xiaomi,mir3p)
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
iodata,wn-dx1167r)
|
||||
iodata_mstc_upgrade_prepare
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
ubiquiti,edgerouterx|\
|
||||
ubiquiti,edgerouterx-sfp)
|
||||
platform_upgrade_ubnt_erx "$1"
|
||||
|
|
|
|||
Loading…
Reference in New Issue