ath79: clean up led config script files for all devices

1. Move all status led definitions out of diag.sh into device dt
   as we use here a generic script hook.

2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>

target/linux/ath79/base-files/etc/board.d/01_leds

@@ -10,7 +10,6 @@ boardname="${board##*,}"
 case "$board" in
 "avm,fritz300e")
 	ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
-	ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"
 	ucidef_set_rssimon "wlan0" "200000" "1"
 	ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:green:rssi0" "wlan0" "1" "100"
 	ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "$boardname:green:rssi1" "wlan0" "20" "100"
@@ -20,13 +19,9 @@ case "$board" in
 	;;
 "etactica,eg200")
 	ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0"
-	ucidef_set_led_wlan "wlan" "WLAN" "$boardname:red:wlan" "phy0tpt"
 	ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33"
 	ucidef_set_led_default "etactica" "etactica" "$boardname:red:etactica" "ignore"
 	;;
-"glinet,ar150")
-	ucidef_set_led_wlan "wlan" "WLAN" "gl-ar150:orange:wlan" "phy0tpt"
-	;;
 "tplink,tl-mr3020-v1")
 	ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x02"
 	;;

target/linux/ath79/base-files/etc/diag.sh

@@ -4,32 +4,7 @@
 
 status_led="$(get_dt_led status)"
 
-get_status_led() {
-	local board=$(board_name)
-	local boardname="${board##*,}"
-
-	case $board in
-	"avm,fritz300e")
-		status_led="${boardname}:green:power"
-		;;
-	"embeddedwireless,dorin")
-		status_led="dorin:green:status"
-		;;
-	"glinet,ar150")
-		status_led="gl-ar150:orange:wlan"
-		;;
-	"tplink,tl-wr1043nd-v1")
-		status_led="tp-link:green:system"
-		;;
-	"ubnt,unifi")
-		status_led="ubnt:green:dome"
-		;;
-	esac
-}
-
 set_state() {
-	[ -z "$status_led" ] && get_status_led
-
 	case "$1" in
 	preinit)
 		status_led_blink_preinit

target/linux/ath79/dts/ar7241_ubnt_unifi.dts

@@ -10,6 +10,10 @@
 	compatible = "ubnt,unifi", "qca,ar7241";
 	model = "Ubiquiti UniFi AP";
 
+	aliases {
+		led-status = &dome_green;
+	};
+
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x4000000>;
@@ -36,7 +40,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		dome-green {
+		dome_green: dome-green {
 			label = "ubnt:green:dome";
 			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
 		};

target/linux/ath79/dts/ar7242_avm_fritz300e.dts

@@ -10,6 +10,10 @@
 	compatible = "avm,fritz300e", "qca,ar7242";
 	model = "AVM FRITZ!WLAN Repeater 300E";
 
+	aliases {
+		led-status = &power;
+	};
+
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x4000000>;
@@ -32,7 +36,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		power: power {
 			label = "fritz300e:green:power";
 			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
 			default-state = "on";
@@ -46,6 +50,7 @@
 		wlan {
 			label = "fritz300e:green:wlan";
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
 		};
 	};
 

target/linux/ath79/dts/ar9330_glinet_ar150.dts

@@ -12,6 +12,7 @@
 
 	aliases {
 		serial0 = &uart;
+		led-status = &wlan;
 	};
 
 	memory@0 {
@@ -22,10 +23,11 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wlan {
+		wlan: wlan {
 			label = "gl-ar150:orange:wlan";
 			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
+			linux,default-trigger = "phy0tpt";
 		};
 
 		lan {

target/linux/ath79/dts/ar9331_embeddedwireless_dorin.dts

@@ -11,6 +11,7 @@
 	compatible = "embeddedwireless,dorin", "qca,ar9331";
 
 	aliases {
+		led-status = &status;
 		serial0 = &uart;
 	};
 
@@ -22,7 +23,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		status: status {
 			label = "dorin:green:status";
 			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
 			default-state = "off";

target/linux/ath79/dts/ar9331_etactica-eg200.dts

@@ -56,6 +56,7 @@
 			label = "eg200:red:wlan";
 			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
+			linux,default-trigger = "phy0tpt";
 		};
 	};
 };