hak5
/
openwrt
mirror of https://github.com/hak5/openwrt.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
openwrt/package/boot/uboot-layerscape/files/ls1012afrdm-uEnv.txt

9 lines
448 B
Plaintext
Raw Normal View History

layerscape: resurrect support for FRDM-LS1012A Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the rest boards supported by LSDK. 0x000000000000-0x000000100000 : "bl2" 0x000000100000-0x000000500000 : "fip" 0x000000500000-0x000000600000 : "u-boot-env" 0x000000600000-0x000000a00000 : "reserved-1" 0x000000a00000-0x000000d00000 : "pfe" 0x000000d00000-0x000000f00000 : "reserved-2" 0x000000f00000-0x000001000000 : "dtb" 0x000001000000-0x000002000000 : "kernel" 0x000002000000-0x000004000000 : "ubifs" Specification SoC: LS1012A single core 800MHz RAM: 512 MB DDR3 Flash: 64 MB QSPI NOR Ethernet: 2x 10/100/1000 Mbps Connectors: µUSB 3.0 OTG µUSB 2.0 (debugging & power input) 2x 3.5mm jack for microphone & headphone (SGTL5000) Arduino Shield expansion with I2C, SPI, UART, and GPIO JTAG LEDS: 3x (non-configurable) Buttons: 1x (reset, non-configurable) Be advised that erasing or writing 64MB flash takes some time to finish. Do not reset the board until all operations end with success, otherwise You'll need external tools to re-program the flash chip. Installation Follow the QSPI programing procedure for LS1012AFRWY board in target/linux/layerscape/README, point 3.3. Don't forget about updating U-Boot environment with MAC addresses of ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1. As the LSDK images do not support sysupgrade, nor do changes in this commit, it's planed in upcoming submissions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-02-25 19:07:36 +00:00
fdtaddr=0x8f000000
loadaddr=0x81000000
fdt_high=0xffffffffffffffff
initrd_high=0xffffffffffffffff
layerscape: ls1012afrdm: introduce dynamic partitioning Combine fixed sizes of "kernel" and "rootfs" partitions into one partition managed by OpenWrt splitter, it will allow better management of chip capacity and less maintenance burden when compiled kernel image will outgrow allocated size for kernel partition. This also changes kernel image format, since splitter only manages kernel and rootfs partitions, the dtb needs to be updated with the kernel, so for convenience, kernel is packed to FIT image. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-02-25 19:07:39 +00:00
qspi_boot=sf probe 0:0;sf read $loadaddr 1000000 2800000;bootm $loadaddr
layerscape: update u-boot to LSDK-20.04 Update u-boot package to latest LSDK-20.04 dropping patches which are no longer needed. Adapt u-boot bootargs to kernel 5.4 for booting. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-03-11 06:55:36 +00:00
bootargs=rootfstype=squashfs,jffs2 noinitrd earlycon=uart8250,mmio,0x21c0500 console=ttyS0,115200 mtdparts=1550000.spi:1m(bl2),4m(fip),1m(u-boot-env),4m(reserved-1),3m(pfe),2m(reserved-2),1m(dtb),-(firmware)
layerscape: resurrect support for FRDM-LS1012A Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the rest boards supported by LSDK. 0x000000000000-0x000000100000 : "bl2" 0x000000100000-0x000000500000 : "fip" 0x000000500000-0x000000600000 : "u-boot-env" 0x000000600000-0x000000a00000 : "reserved-1" 0x000000a00000-0x000000d00000 : "pfe" 0x000000d00000-0x000000f00000 : "reserved-2" 0x000000f00000-0x000001000000 : "dtb" 0x000001000000-0x000002000000 : "kernel" 0x000002000000-0x000004000000 : "ubifs" Specification SoC: LS1012A single core 800MHz RAM: 512 MB DDR3 Flash: 64 MB QSPI NOR Ethernet: 2x 10/100/1000 Mbps Connectors: µUSB 3.0 OTG µUSB 2.0 (debugging & power input) 2x 3.5mm jack for microphone & headphone (SGTL5000) Arduino Shield expansion with I2C, SPI, UART, and GPIO JTAG LEDS: 3x (non-configurable) Buttons: 1x (reset, non-configurable) Be advised that erasing or writing 64MB flash takes some time to finish. Do not reset the board until all operations end with success, otherwise You'll need external tools to re-program the flash chip. Installation Follow the QSPI programing procedure for LS1012AFRWY board in target/linux/layerscape/README, point 3.3. Don't forget about updating U-Boot environment with MAC addresses of ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1. As the LSDK images do not support sysupgrade, nor do changes in this commit, it's planed in upcoming submissions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-02-25 19:07:36 +00:00
bootcmd=echo starting OpenWrt ...;pfe stop;run qspi_boot
bootdelay=3