hak5
/
openwrt
mirror of https://github.com/hak5/openwrt.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
openwrt/target/linux/ipq806x/patches-5.4/083-ipq8064-dtsi-additions....

993 lines
22 KiB
Diff
Raw Normal View History

ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -8,6 +8,8 @@
#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
/ {
#address-cells = <1>;
@@ -28,6 +30,16 @@
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
+ clocks = <&kraitcc 0>, <&kraitcc 4>;
+ clock-names = "cpu", "l2";
+ clock-latency = <100000>;
+ cpu-supply = <&smb208_s2a>;
+ operating-points-v2 = <&opp_table0>;
+ voltage-tolerance = <5>;
+ cooling-min-state = <0>;
+ cooling-max-state = <10>;
+ #cooling-cells = <2>;
+ cpu-idle-states = <&CPU_SPC>;
};
cpu1: cpu@1 {
@@ -38,11 +50,458 @@
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
+ clocks = <&kraitcc 1>, <&kraitcc 4>;
+ clock-names = "cpu", "l2";
+ clock-latency = <100000>;
+ cpu-supply = <&smb208_s2b>;
+ operating-points-v2 = <&opp_table0>;
+ voltage-tolerance = <5>;
+ cooling-min-state = <0>;
+ cooling-max-state = <10>;
+ #cooling-cells = <2>;
+ cpu-idle-states = <&CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
+ qcom,saw = <&saw_l2>;
+ };
+
+ qcom,l2 {
+ qcom,l2-rates = <384000000 1000000000 1200000000>;
+ qcom,l2-cpufreq = <384000000 600000000 1200000000>;
+ qcom,l2-volt = <1100000 1100000 1150000>;
+ qcom,l2-supply = <&smb208_s1a>;
+ };
+
+ idle-states {
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ status = "disabled";
+ entry-latency-us = <400>;
+ exit-latency-us = <900>;
+ min-residency-us = <3000>;
+ };
+ };
+ };
+
+ opp_table0: opp_table0 {
ipq806x: replace nvmem qcom patch with upstream version - Replace nvmem qcom patch with upstream version - Update compatible Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [refresh patches, minor commit message rewording] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-10 11:46:35 +00:00
+ compatible = "operating-points-v2-kryo-cpu";
ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
+ nvmem-cells = <&speedbin_efuse>;
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1000000>;
+ opp-microvolt-speed0-pvs1-v0 = <925000>;
+ opp-microvolt-speed0-pvs2-v0 = <875000>;
+ opp-microvolt-speed0-pvs3-v0 = <800000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1050000>;
+ opp-microvolt-speed0-pvs1-v0 = <975000>;
+ opp-microvolt-speed0-pvs2-v0 = <925000>;
+ opp-microvolt-speed0-pvs3-v0 = <850000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+
+ opp-800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1100000>;
+ opp-microvolt-speed0-pvs1-v0 = <1025000>;
+ opp-microvolt-speed0-pvs2-v0 = <995000>;
+ opp-microvolt-speed0-pvs3-v0 = <900000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1150000>;
+ opp-microvolt-speed0-pvs1-v0 = <1075000>;
+ opp-microvolt-speed0-pvs2-v0 = <1025000>;
+ opp-microvolt-speed0-pvs3-v0 = <950000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1200000>;
+ opp-microvolt-speed0-pvs1-v0 = <1125000>;
+ opp-microvolt-speed0-pvs2-v0 = <1075000>;
+ opp-microvolt-speed0-pvs3-v0 = <1000000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+
+ opp-1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-microvolt-speed0-pvs0-v0 = <1250000>;
+ opp-microvolt-speed0-pvs1-v0 = <1175000>;
+ opp-microvolt-speed0-pvs2-v0 = <1125000>;
+ opp-microvolt-speed0-pvs3-v0 = <1050000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <100000>;
+ };
+ };
+
+ thermal-zones {
+ tsens_tz_sensor0 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 0>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor1 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor2 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 2>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor3 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor4 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 4>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor5 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 5>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor6 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 6>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor7 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 7>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor8 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 8>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor9 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 9>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
+ };
+
+ tsens_tz_sensor10 {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&tsens 10>;
+
+ trips {
+ cpu-critical-hi {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical_high";
+ };
+
+ cpu-config-hi {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "configurable_hi";
+ };
+
+ cpu-config-lo {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "configurable_lo";
+ };
+
+ cpu-critical-low {
+ temperature = <0>;
+ hysteresis = <2000>;
+ type = "critical_low";
+ };
+ };
};
};
@@ -93,6 +552,15 @@
};
};
+ fab-scaling {
+ compatible = "qcom,fab-scaling";
+ clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
+ clock-names = "apps-fab-clk", "ddr-fab-clk";
+ fab_freq_high = <533000000>;
+ fab_freq_nominal = <400000000>;
+ cpu_freq_threshold = <1000000000>;
+ };
+
firmware {
scm {
compatible = "qcom,scm-ipq806x", "qcom,scm";
@@ -120,6 +588,84 @@
reg-names = "lpass-lpaif";
};
+ qfprom: qfprom@700000 {
+ compatible = "qcom,qfprom", "syscon";
+ reg = <0x700000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "okay";
+ tsens_calib: calib@400 {
+ reg = <0x400 0xb>;
+ };
+ tsens_backup: backup@410 {
+ reg = <0x410 0xb>;
+ };
+ speedbin_efuse: speedbin@0c0 {
+ reg = <0x0c0 0x4>;
+ };
+ };
+
+ rpm: rpm@108000 {
+ compatible = "qcom,rpm-ipq8064";
+ reg = <0x108000 0x1000>;
+ qcom,ipc = <&l2cc 0x8 2>;
+
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "ack", "err", "wakeup";
+
+ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+ clock-names = "ram";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ regulators {
+ compatible = "qcom,rpm-smb208-regulators";
+
+ smb208_s1a: s1a {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1150000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+
+ smb208_s1b: s1b {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1150000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+
+ smb208_s2a: s2a {
+ regulator-min-microvolt = < 800000>;
+ regulator-max-microvolt = <1250000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+
+ smb208_s2b: s2b {
+ regulator-min-microvolt = < 800000>;
+ regulator-max-microvolt = <1250000>;
+
+ qcom,switch-mode-frequency = <1200000>;
+ };
+ };
+ };
+
+ rng@1a500000 {
+ compatible = "qcom,prng";
+ reg = <0x1a500000 0x200>;
+ clocks = <&gcc PRNG_CLK>;
+ clock-names = "core";
+ };
+
qcom_pinmux: pinmux@800000 {
compatible = "qcom,ipq8064-pinctrl";
reg = <0x800000 0x4000>;
@@ -159,6 +705,15 @@
};
};
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
@@ -168,6 +723,53 @@
};
};
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29",
+ "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59",
+ "gpio60", "gpio61", "gpio62";
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
leds_pins: leds_pins {
mux {
pins = "gpio7", "gpio8", "gpio9",
@@ -229,6 +831,17 @@
clock-output-names = "acpu1_aux";
};
+ l2cc: clock-controller@2011000 {
+ compatible = "qcom,kpss-gcc", "syscon";
+ reg = <0x2011000 0x1000>;
+ clock-output-names = "acpu_l2_aux";
+ };
+
+ kraitcc: clock-controller {
+ compatible = "qcom,krait-cc-v1";
+ #clock-cells = <1>;
+ };
+
saw0: regulator@2089000 {
compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
@@ -241,6 +854,17 @@
regulator;
};
+ saw_l2: regulator@02012000 {
+ compatible = "qcom,saw2", "syscon";
+ reg = <0x02012000 0x1000>;
+ regulator;
+ };
+
+ sic_non_secure: sic-non-secure@12100000 {
+ compatible = "syscon";
+ reg = <0x12100000 0x10000>;
+ };
+
gsbi2: gsbi@12480000 {
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
@@ -436,6 +1060,15 @@
#power-domain-cells = <1>;
};
+ tsens: thermal-sensor@900000 {
+ compatible = "qcom,ipq8064-tsens";
+ reg = <0x900000 0x3680>;
+ nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+ nvmem-cell-names = "calib", "calib_backup";
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <1>;
+ };
+
tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-ipq8064", "syscon";
reg = <0x1a400000 0x100>;
@@ -448,6 +1081,95 @@
#reset-cells = <1>;
};
+ sfpb_mutex_block: syscon@1200600 {
+ compatible = "syscon";
+ reg = <0x01200600 0x100>;
+ };
+
+ hs_phy_0: hs_phy_0 {
ipq806x: replace phy dwc3 patch with upstream version - Replace dwc3 phy patch with upstream version - Rework the dts to use the upstream bindings - Update changed config flags - Rename module to reflect config name Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-10 11:56:15 +00:00
+ compatible = "qcom,ipq806x-usb-phy-hs";
+ reg = <0x110f8800 0x30>;
ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
+ clocks = <&gcc USB30_0_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
+
+ ss_phy_0: ss_phy_0 {
ipq806x: replace phy dwc3 patch with upstream version - Replace dwc3 phy patch with upstream version - Rework the dts to use the upstream bindings - Update changed config flags - Rename module to reflect config name Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-10 11:56:15 +00:00
+ compatible = "qcom,ipq806x-usb-phy-ss";
+ reg = <0x110f8830 0x30>;
ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
+
+ usb3_0: usb3@110f8800 {
+ compatible = "qcom,dwc3", "syscon";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x110f8800 0x8000>;
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "core";
+
+ ranges;
+
+ resets = <&gcc USB30_0_MASTER_RESET>;
+ reset-names = "master";
+
+ status = "disabled";
+
+ dwc3_0: dwc3@11000000 {
+ compatible = "snps,dwc3";
+ reg = <0x11000000 0xcd00>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&hs_phy_0>, <&ss_phy_0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ snps,dis_u3_susphy_quirk;
+ };
+ };
+
+ hs_phy_1: hs_phy_1 {
ipq806x: replace phy dwc3 patch with upstream version - Replace dwc3 phy patch with upstream version - Rework the dts to use the upstream bindings - Update changed config flags - Rename module to reflect config name Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-10 11:56:15 +00:00
+ compatible = "qcom,ipq806x-usb-phy-hs";
+ reg = <0x100f8800 0x30>;
ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
+ clocks = <&gcc USB30_1_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
+
+ ss_phy_1: ss_phy_1 {
ipq806x: replace phy dwc3 patch with upstream version - Replace dwc3 phy patch with upstream version - Rework the dts to use the upstream bindings - Update changed config flags - Rename module to reflect config name Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-10 11:56:15 +00:00
+ compatible = "qcom,ipq806x-usb-phy-ss";
+ reg = <0x100f8830 0x30>;
ipq806x: use qcom-ipq8064.dtsi from upstream Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 09:12:10 +00:00
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
+
+ usb3_1: usb3@100f8800 {
+ compatible = "qcom,dwc3", "syscon";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x100f8800 0x8000>;
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "core";
+
+ ranges;
+
+ resets = <&gcc USB30_1_MASTER_RESET>;
+ reset-names = "master";
+
+ status = "disabled";
+
+ dwc3_1: dwc3@10000000 {
+ compatible = "snps,dwc3";
+ reg = <0x10000000 0xcd00>;
+ interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&hs_phy_1>, <&ss_phy_1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ snps,dis_u3_susphy_quirk;
+ };
+ };
+
pcie0: pci@1b500000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b500000 0x1000
@@ -601,6 +1323,167 @@
perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
};
+ adm_dma: dma@18300000 {
+ compatible = "qcom,adm";
+ reg = <0x18300000 0x100000>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+
+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+ clock-names = "core", "iface";
+
+ resets = <&gcc ADM0_RESET>,
+ <&gcc ADM0_PBUS_RESET>,
+ <&gcc ADM0_C0_RESET>,
+ <&gcc ADM0_C1_RESET>,
+ <&gcc ADM0_C2_RESET>;
+ reset-names = "clk", "pbus", "c0", "c1", "c2";
+ qcom,ee = <0>;
+
+ status = "disabled";
+ };
+
+ nand_controller: nand-controller@1ac00000 {
+ compatible = "qcom,ipq806x-nand";
+ reg = <0x1ac00000 0x800>;
+
+ clocks = <&gcc EBI2_CLK>,
+ <&gcc EBI2_AON_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&adm_dma 3>;
+ dma-names = "rxtx";
+ qcom,cmd-crci = <15>;
+ qcom,data-crci = <3>;
+
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ nss_common: syscon@03000000 {
+ compatible = "syscon";
+ reg = <0x03000000 0x0000FFFF>;
+ };
+
+ qsgmii_csr: syscon@1bb00000 {
+ compatible = "syscon";
+ reg = <0x1bb00000 0x000001FF>;
+ };
+
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <7>;
+ snps,rd_osr_lmt = <7>;
+ snps,blen = <16 0 0 0 0 0 0>;
+ };
+
+ mdio0: mdio@37000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ compatible = "qcom,ipq8064-mdio", "syscon";
+ reg = <0x37000000 0x200000>;
+ resets = <&gcc GMAC_CORE1_RESET>;
+ reset-names = "stmmaceth";
+ clocks = <&gcc GMAC_CORE1_CLK>;
+ clock-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac0: ethernet@37000000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37000000 0x200000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE1_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE1_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac1: ethernet@37200000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac";
+ reg = <0x37200000 0x200000>;
+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE2_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE2_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac2: ethernet@37400000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+ reg = <0x37400000 0x200000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE3_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE3_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
+ gmac3: ethernet@37600000 {
+ device_type = "network";
+ compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+ reg = <0x37600000 0x200000>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,pbl = <32>;
+ snps,aal = <1>;
+
+ qcom,nss-common = <&nss_common>;
+ qcom,qsgmii-csr = <&qsgmii_csr>;
+
+ clocks = <&gcc GMAC_CORE4_CLK>;
+ clock-names = "stmmaceth";
+
+ resets = <&gcc GMAC_CORE4_RESET>;
+ reset-names = "stmmaceth";
+
+ status = "disabled";
+ };
+
vsdcc_fixed: vsdcc-regulator {
compatible = "regulator-fixed";
regulator-name = "SDCC Power";
@@ -676,4 +1559,17 @@
};
};
};
+
+ sfpb_mutex: sfpb-mutex {
+ compatible = "qcom,sfpb-mutex";
+ syscon = <&sfpb_mutex_block 4 4>;
+
+ #hwlock-cells = <1>;
+ };
+
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem>;
+ hwlocks = <&sfpb_mutex 3>;
+ };
};