openwrt/target/linux/brcm2708/patches-3.10/0141-V4L2-Fix-issue-when-sw...

160 lines
4.9 KiB
Diff
Raw Normal View History

From 50a40e8c2a9014c62943b034edefa035c0647519 Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dsteve@broadcom.com>
Date: Mon, 9 Dec 2013 11:24:55 +0000
Subject: [PATCH 141/174] V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
---
drivers/media/platform/bcm2835/bcm2835-camera.c | 126 ++++++++++++++----------
1 file changed, 72 insertions(+), 54 deletions(-)
--- a/drivers/media/platform/bcm2835/bcm2835-camera.c
+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
@@ -955,69 +955,87 @@ static int mmal_setup_components(struct
camera_port->current_buffer.num =
camera_port->recommended_buffer.num;
- port->format.encoding = mfmt->mmal;
- port->format.encoding_variant = 0;
- /* Set any encoding specific parameters */
- switch (mfmt->mmal_component) {
- case MMAL_COMPONENT_VIDEO_ENCODE:
- port->format.bitrate =
- dev->capture.encode_bitrate;
- break;
- case MMAL_COMPONENT_IMAGE_ENCODE:
- /* Could set EXIF parameters here */
- break;
- default:
- break;
- }
- ret = vchiq_mmal_port_set_format(dev->instance, port);
-
+ ret =
+ vchiq_mmal_port_connect_tunnel(
+ dev->instance,
+ camera_port,
+ &encode_component->input[0]);
if (ret) {
- v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
- "%s failed to set format\n", __func__);
+ v4l2_dbg(1, bcm2835_v4l2_debug,
+ &dev->v4l2_dev,
+ "%s failed to create connection\n",
+ __func__);
+ /* ensure capture is not going to be tried */
+ dev->capture.port = NULL;
} else {
+ port->es.video.width = f->fmt.pix.width;
+ port->es.video.height = f->fmt.pix.height;
+ port->es.video.crop.x = 0;
+ port->es.video.crop.y = 0;
+ port->es.video.crop.width = f->fmt.pix.width;
+ port->es.video.crop.height = f->fmt.pix.height;
+ port->es.video.frame_rate.num =
+ dev->capture.timeperframe.denominator;
+ port->es.video.frame_rate.den =
+ dev->capture.timeperframe.numerator;
+
+ port->format.encoding = mfmt->mmal;
+ port->format.encoding_variant = 0;
+ /* Set any encoding specific parameters */
+ switch (mfmt->mmal_component) {
+ case MMAL_COMPONENT_VIDEO_ENCODE:
+ port->format.bitrate =
+ dev->capture.encode_bitrate;
+ break;
+ case MMAL_COMPONENT_IMAGE_ENCODE:
+ /* Could set EXIF parameters here */
+ break;
+ default:
+ break;
+ }
+ ret = vchiq_mmal_port_set_format(dev->instance,
+ port);
+ if (ret)
+ v4l2_dbg(1, bcm2835_v4l2_debug,
+ &dev->v4l2_dev,
+ "%s failed to set format\n",
+ __func__);
+ }
+
+ if (!ret) {
ret = vchiq_mmal_component_enable(
dev->instance,
encode_component);
if (ret) {
v4l2_dbg(1, bcm2835_v4l2_debug,
- &dev->v4l2_dev,
- "%s Failed to enable encode components\n",
- __func__);
- } else {
- /* configure buffering */
- port->current_buffer.num = 1;
- port->current_buffer.size =
- f->fmt.pix.sizeimage;
- if (port->format.encoding ==
- MMAL_ENCODING_JPEG) {
- v4l2_dbg(1, bcm2835_v4l2_debug,
- &dev->v4l2_dev,
- "JPEG - fiddle buffer size\n");
- port->current_buffer.size =
- (f->fmt.pix.sizeimage <
- (100 << 10))
- ? (100 << 10) : f->fmt.pix.
- sizeimage;
- }
+ &dev->v4l2_dev,
+ "%s Failed to enable encode components\n",
+ __func__);
+ }
+ }
+ if (!ret) {
+ /* configure buffering */
+ port->current_buffer.num = 1;
+ port->current_buffer.size =
+ f->fmt.pix.sizeimage;
+ if (port->format.encoding ==
+ MMAL_ENCODING_JPEG) {
v4l2_dbg(1, bcm2835_v4l2_debug,
- &dev->v4l2_dev,
- "vid_cap - current_buffer.size being set to %d\n",
- f->fmt.pix.sizeimage);
- port->current_buffer.alignment = 0;
- ret =
- vchiq_mmal_port_connect_tunnel(
- dev->instance,
- camera_port,
- &encode_component->input[0]);
- if (ret) {
- v4l2_dbg(1, bcm2835_v4l2_debug,
- &dev->v4l2_dev,
- "%s failed to create connection\n",
- __func__);
- /* ensure capture is not going to be tried */
- dev->capture.port = NULL;
- }
+ &dev->v4l2_dev,
+ "JPG - buf size now %d was %d\n",
+ f->fmt.pix.sizeimage,
+ port->current_buffer.size);
+ port->current_buffer.size =
+ (f->fmt.pix.sizeimage <
+ (100 << 10))
+ ? (100 << 10) : f->fmt.pix.
+ sizeimage;
}
+ v4l2_dbg(1, bcm2835_v4l2_debug,
+ &dev->v4l2_dev,
+ "vid_cap - cur_buf.size set to %d\n",
+ f->fmt.pix.sizeimage);
+ port->current_buffer.alignment = 0;
}
} else {
/* configure buffering */