openwrt/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-qxwlan-e2600ac...

263 lines
4.1 KiB
Plaintext
Raw Normal View History

ipq40xx: add support for Qxwlan E2600AC C1 and C2 Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-21 05:28:32 +00:00
/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
*
* Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
*
*/
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Qxwlan E2600AC";
compatible = "qcom,ipq4019";
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256MB */
};
soc {
mdio@90000 {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
};
ess-psgmii@98000 {
status = "okay";
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
/* select hostmode */
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
status = "okay";
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
usb2: usb2@60f8800 {
status = "okay";
dwc3@6000000 {
#address-cells = <1>;
#size-cells = <0>;
usb2_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
};
serial@78af000 {
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
status = "okay";
};
serial@78b0000 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
status = "okay";
};
i2c@78b7000 { /* BLSP1 QUP2 */
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "okay";
};
usb3: usb3@8af8800 {
status = "okay";
dwc3@8a00000 {
#address-cells = <1>;
#size-cells = <0>;
usb3_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
usb3_port2: port@2 {
reg = <2>;
#trigger-source-cells = <0>;
};
};
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
};
edma@c080000 {
status = "okay";
};
leds {
compatible = "gpio-leds";
led1 {
label = "e2600ac:green:wlan0";
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
};
led2 {
label = "e2600ac:green:wlan1";
gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
};
led3 {
label = "e2600ac:green:usb";
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>;
linux,default-trigger = "usbport";
};
led4 {
label = "e2600ac:green:ctrl1";
gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
};
led5 {
label = "e2600ac:green:ctrl2";
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
};
led6 {
label = "e2600ac:green:ctrl3";
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
};
&blsp_dma {
status = "okay";
};
&cryptobam {
status = "okay";
};
&qpic_bam {
status = "okay";
};
&tlmm {
i2c_0_pins: i2c-0-pinmux {
mux {
pins = "gpio20", "gpio21";
function = "blsp_i2c0";
bias-disable;
};
};
mdio_pins: mdio_pinmux {
mux_1 {
pins = "gpio6";
function = "mdio";
bias-pull-up;
};
mux_2 {
pins = "gpio7";
function = "mdc";
bias-pull-up;
};
};
serial_0_pins: serial0-pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
serial_1_pins: serial1_pinmux {
mux {
pins = "gpio8", "gpio9";
function = "blsp_uart1";
bias-disable;
};
};
spi_0_pins: spi_0_pinmux {
pinmux {
function = "blsp_spi0";
pins = "gpio13", "gpio14", "gpio15";
drive-strength = <12>;
bias-disable;
};
pinmux_cs {
function = "gpio";
pins = "gpio12";
drive-strength = <2>;
bias-disable;
output-high;
};
};
};
&usb3_ss_phy {
status = "okay";
};
&usb3_hs_phy {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
};