openwrt/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5...

63 lines
1020 B
Plaintext
Raw Normal View History

ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qca9563_tplink_archer-x7-v5.dtsi"
/ {
compatible = "tplink,archer-a7-v5", "qca,qca9563";
model = "TP-Link Archer A7 v5";
};
&keys {
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
&mtdparts {
partition@0 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "factory-uboot";
reg = <0x000000 0x020000>;
read-only;
};
uboot: partition@20000 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "u-boot";
reg = <0x020000 0x020000>;
read-only;
};
partition@40000 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "firmware";
reg = <0x040000 0xec0000>;
compatible = "denx,uimage";
};
info: partition@f40000 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "info";
reg = <0xf40000 0x020000>;
read-only;
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
};
config: partition@f60000 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "config";
reg = <0xf60000 0x050000>;
read-only;
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
};
partition@fc0000 {
label = "partition-table";
reg = <0xfc0000 0x010000>;
read-only;
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
};
art: partition@ff0000 {
ath79: add support for TP-Link Archer A7 This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-12 16:56:15 +00:00
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};