openwrt/target/linux/ramips/dts/NA930.dts

165 lines
2.5 KiB
Plaintext
Raw Normal View History

/dts-v1/;
/include/ "mt7620a.dtsi"
/ {
compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
model = "Sercomm NA930";
chosen {
bootargs = "console=ttyS1,57600";
};
pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "rgmii2", "spi", "ephy";
ralink,function = "gpio";
};
uartf_gpio {
ralink,group = "uartf";
ralink,function = "gpio uartf";
};
};
};
palmbus@10000000 {
uart@500 {
status = "okay";
};
gpio@638 {
status = "okay";
};
gpio@660 {
status = "okay";
};
};
nand {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mtk,mt7620-nand";
partition@0 {
label = "u-boot";
reg = <0x0 0x20000>;
read-only;
};
partition@200000 {
label = "factory";
reg = <0x200000 0x40000>;
read-only;
};
partition@240000 {
label = "Config";
reg = <0x240000 0x400000>;
read-only;
};
partition@640000 {
label = "firmware";
reg = <0x640000 0x1400000>;
};
};
ethernet@10100000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
ralink,port-map = "llllw";
port@4 {
status = "okay";
phy-handle = <&phy4>;
phy-mode = "rgmii";
};
port@5 {
status = "okay";
phy-handle = <&phy5>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii";
};
phy5: ethernet-phy@5 {
reg = <5>;
phy-mode = "rgmii";
};
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio0 11 1>;
linux,code = <0x198>;
};
zwave {
label = "zwave";
gpios = <&gpio0 12 1>;
linux,code = <0x100>;
};
wps {
label = "wps";
gpios = <&gpio0 14 1>;
linux,code = <0x211>;
};
};
gpio-leds {
compatible = "gpio-leds";
zwave {
label = "na930:blue:zwave";
gpios = <&gpio2 0 1>;
};
status {
label = "na930:blue:status";
gpios = <&gpio2 26 1>;
};
service {
label = "na930:blue:service";
gpios = <&gpio2 28 1>;
};
power {
label = "na930:blue:power";
gpios = <&gpio2 29 1>;
};
};
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
telit {
gpio-export,name = "telit";
gpio-export,output = <1>;
gpios = <&gpio0 13 0>;
};
};
gsw@10110000 {
ralink,port4 = "gmac";
};
ehci@101c0000 {
status = "okay";
};
ohci@101c1000 {
status = "okay";
};
};