mirror of https://github.com/hak5/openwrt.git
257 lines
4.8 KiB
Plaintext
257 lines
4.8 KiB
Plaintext
|
/include/ "vr9.dtsi"
|
||
|
|
||
|
/ {
|
||
|
model = "VGV7510KW22 - o2 Box 6431";
|
||
|
|
||
|
chosen {
|
||
|
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
|
||
|
};
|
||
|
|
||
|
memory@0 {
|
||
|
reg = <0x0 0x4000000>;
|
||
|
};
|
||
|
|
||
|
fpi@10000000 {
|
||
|
localbus@0 {
|
||
|
nor-boot@0 {
|
||
|
compatible = "lantiq,nor";
|
||
|
bank-width = <2>;
|
||
|
reg = <0 0x0 0x1000000>;
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <1>;
|
||
|
|
||
|
boardconfig: partition@fe0000 {
|
||
|
label = "board_config";
|
||
|
reg = <0xfe0000 0x20000>;
|
||
|
read-only;
|
||
|
};
|
||
|
};
|
||
|
};
|
||
|
|
||
|
gpio: pinmux@E100B10 {
|
||
|
pinctrl-names = "default";
|
||
|
pinctrl-0 = <&state_default>;
|
||
|
|
||
|
state_default: pinmux {
|
||
|
ip101a-rst {
|
||
|
lantiq,pins = "io46";
|
||
|
lantiq,output = <0>;
|
||
|
lantiq,pull = <1>;
|
||
|
};
|
||
|
gphy-leds {
|
||
|
lantiq,groups = "gphy0 led1",
|
||
|
"gphy1 led0", "gphy1 led1";
|
||
|
lantiq,function = "gphy";
|
||
|
lantiq,open-drain = <0>;
|
||
|
lantiq,pull = <0>;
|
||
|
lantiq,output = <1>;
|
||
|
};
|
||
|
stp {
|
||
|
lantiq,groups = "stp";
|
||
|
lantiq,function = "stp";
|
||
|
lantiq,pull = <2>;
|
||
|
lantiq,open-drain = <0>;
|
||
|
lantiq,output = <1>;
|
||
|
};
|
||
|
mdio {
|
||
|
lantiq,groups = "mdio";
|
||
|
lantiq,function = "mdio";
|
||
|
};
|
||
|
pci-rst {
|
||
|
lantiq,pins = "io21";
|
||
|
lantiq,open-drain = <0>;
|
||
|
lantiq,pull = <0>;
|
||
|
lantiq,output = <1>;
|
||
|
};
|
||
|
spi {
|
||
|
lantiq,groups = "spi";
|
||
|
lantiq,function = "spi";
|
||
|
};
|
||
|
};
|
||
|
};
|
||
|
|
||
|
eth@E108000 {
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <0>;
|
||
|
compatible = "lantiq,xrx200-net";
|
||
|
reg = < 0xE108000 0x3000 /* switch */
|
||
|
0xE10B100 0x70 /* mdio */
|
||
|
0xE10B1D8 0x30 /* mii */
|
||
|
0xE10B308 0x30 /* pmac */
|
||
|
>;
|
||
|
interrupt-parent = <&icu0>;
|
||
|
interrupts = <73 72>;
|
||
|
|
||
|
lan: interface@0 {
|
||
|
compatible = "lantiq,xrx200-pdi";
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <0>;
|
||
|
reg = <0>;
|
||
|
mtd-mac-address = <&boardconfig 0x16>;
|
||
|
lantiq,switch;
|
||
|
|
||
|
ethernet@2 {
|
||
|
compatible = "lantiq,xrx200-pdi-port";
|
||
|
reg = <2>;
|
||
|
phy-mode = "mii";
|
||
|
phy-handle = <&phy11>;
|
||
|
};
|
||
|
ethernet@3 {
|
||
|
compatible = "lantiq,xrx200-pdi-port";
|
||
|
reg = <3>;
|
||
|
phy-mode = "mii";
|
||
|
phy-handle = <&phy12>;
|
||
|
};
|
||
|
ethernet@4 {
|
||
|
compatible = "lantiq,xrx200-pdi-port";
|
||
|
reg = <4>;
|
||
|
phy-mode = "mii";
|
||
|
phy-handle = <&phy13>;
|
||
|
};
|
||
|
ethernet@5 {
|
||
|
compatible = "lantiq,xrx200-pdi-port";
|
||
|
reg = <5>;
|
||
|
phy-mode = "mii";
|
||
|
phy-handle = <&phy14>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
mdio@0 {
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <0>;
|
||
|
compatible = "lantiq,xrx200-mdio";
|
||
|
|
||
|
phy11: ethernet-phy@11 {
|
||
|
reg = <0x11>;
|
||
|
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
|
||
|
};
|
||
|
phy12: ethernet-phy@12 {
|
||
|
reg = <0x12>;
|
||
|
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
|
||
|
};
|
||
|
phy13: ethernet-phy@13 {
|
||
|
reg = <0x13>;
|
||
|
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
|
||
|
};
|
||
|
phy14: ethernet-phy@14 {
|
||
|
reg = <0x14>;
|
||
|
compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
|
||
|
};
|
||
|
};
|
||
|
};
|
||
|
|
||
|
stp: stp@E100BB0 {
|
||
|
compatible = "lantiq,gpio-stp-xway";
|
||
|
reg = <0xE100BB0 0x40>;
|
||
|
#gpio-cells = <2>;
|
||
|
gpio-controller;
|
||
|
|
||
|
lantiq,shadow = <0xff>;
|
||
|
lantiq,groups = <0x1>;
|
||
|
lantiq,dsl = <0x0>;
|
||
|
lantiq,phy1 = <0x7>;
|
||
|
lantiq,phy2 = <0x7>; /* enable gphy0 led2 = LAN2 LED */
|
||
|
};
|
||
|
|
||
|
ifxhcd@E101000 {
|
||
|
status = "okay";
|
||
|
gpios = <&gpio 47 0>;
|
||
|
};
|
||
|
|
||
|
pci@E105400 {
|
||
|
status = "okay";
|
||
|
lantiq,bus-clock = <33333333>;
|
||
|
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
|
||
|
interrupt-map = <
|
||
|
0x7000 0 0 1 &icu0 30 1 // slot 14, irq 30
|
||
|
>;
|
||
|
gpio-reset = <&gpio 21 0>;
|
||
|
req-mask = <0x1>; /* GNT1 */
|
||
|
};
|
||
|
|
||
|
pcie@d900000 {
|
||
|
status = "disabled";
|
||
|
};
|
||
|
};
|
||
|
|
||
|
gphy-xrx200 {
|
||
|
compatible = "lantiq,phy-xrx200";
|
||
|
firmware1 = "lantiq/vr9_phy22f_a1x.bin"; /*VR9 1.1*/
|
||
|
firmware2 = "lantiq/vr9_phy22f_a2x.bin"; /*VR9 1.2*/
|
||
|
phys = [ 00 01 ];
|
||
|
};
|
||
|
|
||
|
ralink_eep {
|
||
|
compatible = "ralink,eeprom";
|
||
|
ralink,eeprom = "RT3062.eeprom";
|
||
|
};
|
||
|
|
||
|
gpio-keys-polled {
|
||
|
compatible = "gpio-keys-polled";
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <0>;
|
||
|
poll-interval = <100>;
|
||
|
|
||
|
reset {
|
||
|
label = "reset";
|
||
|
gpios = <&gpio 6 1>;
|
||
|
linux,code = <0x198>;
|
||
|
};
|
||
|
|
||
|
wps {
|
||
|
label = "wps";
|
||
|
gpios = <&gpio 9 1>;
|
||
|
linux,code = <0x211>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
gpio-leds {
|
||
|
compatible = "gpio-leds";
|
||
|
|
||
|
dsl {
|
||
|
label = "dsl";
|
||
|
gpios = <&gpio 2 1>;
|
||
|
};
|
||
|
|
||
|
internet_red {
|
||
|
label = "internet_red";
|
||
|
gpios = <&gpio 10 1>;
|
||
|
};
|
||
|
|
||
|
info_red {
|
||
|
label = "info_red";
|
||
|
gpios = <&gpio 12 1>;
|
||
|
};
|
||
|
|
||
|
power {
|
||
|
label = "power"; /* green */
|
||
|
gpios = <&gpio 14 1>;
|
||
|
};
|
||
|
|
||
|
info_green {
|
||
|
label = "info_green";
|
||
|
gpios = <&gpio 15 1>;
|
||
|
};
|
||
|
|
||
|
internet_green {
|
||
|
label = "internet_green";
|
||
|
gpios = <&gpio 19 1>;
|
||
|
};
|
||
|
|
||
|
wifi {
|
||
|
label = "wifi";
|
||
|
gpios = <&gpio 20 1>;
|
||
|
};
|
||
|
|
||
|
power2 {
|
||
|
label = "power2"; /* red */
|
||
|
gpios = <&gpio 28 1>;
|
||
|
};
|
||
|
|
||
|
phone_red {
|
||
|
label = "phone_red";
|
||
|
gpios = <&gpio 29 1>;
|
||
|
};
|
||
|
};
|
||
|
};
|