openwrt/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064.dtsi

1409 lines
30 KiB
Plaintext
Raw Normal View History

/dts-v1/;
#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
#include <dt-bindings/mfd/qcom-rpm.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Qualcomm IPQ8064";
compatible = "qcom,ipq8064";
interrupt-parent = <&intc>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <0>;
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
clocks = <&kraitcc 0>, <&kraitcc 4>;
clock-names = "cpu", "l2";
clock-latency = <100000>;
cpu-supply = <&smb208_s2a>;
voltage-tolerance = <5>;
cooling-min-state = <0>;
cooling-max-state = <10>;
#cooling-cells = <2>;
cpu-idle-states = <&CPU_SPC>;
};
cpu1: cpu@1 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <1>;
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
clocks = <&kraitcc 1>, <&kraitcc 4>;
clock-names = "cpu", "l2";
clock-latency = <100000>;
cpu-supply = <&smb208_s2b>;
cooling-min-state = <0>;
cooling-max-state = <10>;
#cooling-cells = <2>;
cpu-idle-states = <&CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
qcom,saw = <&saw_l2>;
};
qcom,l2 {
qcom,l2-rates = <384000000 1000000000 1200000000>;
};
idle-states {
CPU_SPC: spc {
compatible = "qcom,idle-state-spc",
"arm,idle-state";
entry-latency-us = <400>;
exit-latency-us = <900>;
min-residency-us = <3000>;
};
};
};
thermal-zones {
tsens_tz_sensor0 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 0>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor1 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 1>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor2 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 2>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor3 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 3>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor4 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 4>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor5 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 5>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor6 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 6>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor7 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 7>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor8 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 8>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor9 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 9>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
tsens_tz_sensor10 {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens 10>;
trips {
cpu-critical-hi {
temperature = <125000>;
hysteresis = <2000>;
type = "critical_high";
};
cpu-config-hi {
temperature = <105000>;
hysteresis = <2000>;
type = "configurable_hi";
};
cpu-config-lo {
temperature = <95000>;
hysteresis = <2000>;
type = "configurable_lo";
};
cpu-critical-low {
temperature = <0>;
hysteresis = <2000>;
type = "critical_low";
};
};
};
};
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 10 0x304>;
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
nss@40000000 {
reg = <0x40000000 0x1000000>;
no-map;
};
smem: smem@41000000 {
reg = <0x41000000 0x200000>;
no-map;
};
};
clocks {
cxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
pxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
sleep_clk: sleep_clk {
compatible = "fixed-clock";
clock-frequency = <32768>;
#clock-cells = <0>;
};
};
firmware {
scm {
compatible = "qcom,scm-ipq806x";
};
};
kraitcc: clock-controller {
compatible = "qcom,krait-cc-v1";
#clock-cells = <1>;
};
qcom,pvs {
qcom,pvs-format-a;
qcom,speed0-pvs0-bin-v0 =
< 1400000000 1250000 >,
< 1200000000 1200000 >,
< 1000000000 1150000 >,
< 800000000 1100000 >,
< 600000000 1050000 >,
< 384000000 1000000 >;
qcom,speed0-pvs1-bin-v0 =
< 1400000000 1175000 >,
< 1200000000 1125000 >,
< 1000000000 1075000 >,
< 800000000 1025000 >,
< 600000000 975000 >,
< 384000000 925000 >;
qcom,speed0-pvs2-bin-v0 =
< 1400000000 1125000 >,
< 1200000000 1075000 >,
< 1000000000 1025000 >,
< 800000000 995000 >,
< 600000000 925000 >,
< 384000000 875000 >;
qcom,speed0-pvs3-bin-v0 =
< 1400000000 1050000 >,
< 1200000000 1000000 >,
< 1000000000 950000 >,
< 800000000 900000 >,
< 600000000 850000 >,
< 384000000 800000 >;
};
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "simple-bus";
lpass@28100000 {
compatible = "qcom,lpass-cpu";
status = "disabled";
clocks = <&lcc AHBIX_CLK>,
<&lcc MI2S_OSR_CLK>,
<&lcc MI2S_BIT_CLK>;
clock-names = "ahbix-clk",
"mi2s-osr-clk",
"mi2s-bit-clk";
interrupts = <0 85 1>;
interrupt-names = "lpass-irq-lpaif";
reg = <0x28100000 0x10000>;
reg-names = "lpass-lpaif";
};
qfprom: qfprom@700000 {
compatible = "qcom,qfprom", "syscon";
reg = <0x700000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
status = "okay";
tsens_calib: calib@400 {
reg = <0x400 0x10>;
};
tsens_backup: backup@410 {
reg = <0x410 0x10>;
};
};
rpm@108000 {
compatible = "qcom,rpm-ipq8064";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
interrupts = <0 19 0>,
<0 21 0>,
<0 22 0>;
interrupt-names = "ack",
"err",
"wakeup";
clocks = <&gcc RPM_MSG_RAM_H_CLK>;
clock-names = "ram";
#address-cells = <1>;
#size-cells = <0>;
rpmcc: clock-controller {
compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
#clock-cells = <1>;
};
regulators {
compatible = "qcom,rpm-smb208-regulators";
smb208_s1a: s1a {
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1150000>;
qcom,switch-mode-frequency = <1200000>;
};
smb208_s1b: s1b {
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1150000>;
qcom,switch-mode-frequency = <1200000>;
};
smb208_s2a: s2a {
regulator-min-microvolt = < 800000>;
regulator-max-microvolt = <1250000>;
qcom,switch-mode-frequency = <1200000>;
};
smb208_s2b: s2b {
regulator-min-microvolt = < 800000>;
regulator-max-microvolt = <1250000>;
qcom,switch-mode-frequency = <1200000>;
};
};
};
rng@1a500000 {
compatible = "qcom,prng";
reg = <0x1a500000 0x200>;
clocks = <&gcc PRNG_CLK>;
clock-names = "core";
};
qcom_pinmux: pinmux@800000 {
compatible = "qcom,ipq8064-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 0x4>;
pcie0_pins: pcie0_pinmux {
mux {
pins = "gpio3";
function = "pcie1_rst";
drive-strength = <2>;
bias-disable;
};
};
pcie1_pins: pcie1_pinmux {
mux {
pins = "gpio48";
function = "pcie2_rst";
drive-strength = <2>;
bias-disable;
};
};
pcie2_pins: pcie2_pinmux {
mux {
pins = "gpio63";
function = "pcie3_rst";
drive-strength = <2>;
bias-disable;
output-low;
};
};
};
intc: interrupt-controller@2000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x02000000 0x1000>,
<0x02002000 0x1000>;
};
timer@200a000 {
compatible = "qcom,kpss-timer", "qcom,msm-timer";
interrupts = <1 1 0x301>,
<1 2 0x301>,
<1 3 0x301>,
<1 4 0x301>,
<1 5 0x301>;
reg = <0x0200a000 0x100>;
clock-frequency = <25000000>,
<32768>;
clocks = <&sleep_clk>;
clock-names = "sleep";
cpu-offset = <0x80000>;
};
acc0: clock-controller@2088000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
clock-output-names = "acpu0_aux";
};
acc1: clock-controller@2098000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
clock-output-names = "acpu1_aux";
};
l2cc: clock-controller@2011000 {
compatible = "qcom,kpss-gcc", "syscon";
reg = <0x2011000 0x1000>;
clock-output-names = "acpu_l2_aux";
};
saw0: regulator@2089000 {
compatible = "qcom,saw2", "syscon";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw1: regulator@2099000 {
compatible = "qcom,saw2", "syscon";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw_l2: regulator@02012000 {
compatible = "qcom,saw2", "syscon";
reg = <0x02012000 0x1000>;
regulator;
};
sic_non_secure: sic-non-secure@12100000 {
compatible = "syscon";
reg = <0x12100000 0x10000>;
};
gsbi2: gsbi@12480000 {
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
reg = <0x12480000 0x100>;
clocks = <&gcc GSBI2_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
status = "disabled";
syscon-tcsr = <&tcsr>;
uart2: serial@12490000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x12490000 0x1000>,
<0x12480000 0x1000>;
interrupts = <0 195 0x0>;
clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
i2c@124a0000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x124a0000 0x1000>;
interrupts = <0 196 0>;
clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi4: gsbi@16300000 {
compatible = "qcom,gsbi-v1.0.0";
cell-index = <4>;
reg = <0x16300000 0x100>;
clocks = <&gcc GSBI4_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
status = "disabled";
syscon-tcsr = <&tcsr>;
gsbi4_serial: serial@16340000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16340000 0x1000>,
<0x16300000 0x1000>;
interrupts = <0 152 0x0>;
clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
i2c@16380000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x16380000 0x1000>;
interrupts = <0 153 0>;
clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi5: gsbi@1a200000 {
compatible = "qcom,gsbi-v1.0.0";
cell-index = <5>;
reg = <0x1a200000 0x100>;
clocks = <&gcc GSBI5_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
status = "disabled";
syscon-tcsr = <&tcsr>;
uart5: serial@1a240000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x1000>,
<0x1a200000 0x1000>;
interrupts = <0 154 0x0>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
i2c@1a280000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
interrupts = <0 155 0>;
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
spi@1a280000 {
compatible = "qcom,spi-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
interrupts = <0 155 0>;
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
sata_phy: sata-phy@1b400000 {
compatible = "qcom,ipq806x-sata-phy";
reg = <0x1b400000 0x200>;
clocks = <&gcc SATA_PHY_CFG_CLK>;
clock-names = "cfg";
#phy-cells = <0>;
status = "disabled";
};
sata@29000000 {
compatible = "qcom,ipq806x-ahci", "generic-ahci";
reg = <0x29000000 0x180>;
interrupts = <0 209 0x0>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
<&gcc SATA_A_CLK>,
<&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
clock-names = "slave_face", "iface", "core",
"rxoob", "pmalive";
assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
assigned-clock-rates = <100000000>, <100000000>;
phys = <&sata_phy>;
phy-names = "sata-phy";
status = "disabled";
};
qcom,ssbi@500000 {
compatible = "qcom,ssbi";
reg = <0x00500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
};
gcc: clock-controller@900000 {
compatible = "qcom,gcc-ipq8064";
reg = <0x00900000 0x4000>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
};
tsens: thermal-sensor@900000 {
compatible = "qcom,ipq8064-tsens";
reg = <0x900000 0x3680>;
nvmem-cells = <&tsens_calib>, <&tsens_backup>;
nvmem-cell-names = "calib", "calib_backup";
interrupts = <0 178 0>;
#thermal-sensor-cells = <1>;
};
tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-ipq8064", "syscon";
reg = <0x1a400000 0x100>;
};
lcc: clock-controller@28000000 {
compatible = "qcom,lcc-ipq8064";
reg = <0x28000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
sfpb_mutex_block: syscon@1200600 {
compatible = "syscon";
reg = <0x01200600 0x100>;
};
hs_phy_1: phy@100f8800 {
compatible = "qcom,dwc3-hs-usb-phy";
reg = <0x100f8800 0x30>;
clocks = <&gcc USB30_1_UTMI_CLK>;
clock-names = "ref";
#phy-cells = <0>;
status = "disabled";
};
ss_phy_1: phy@100f8830 {
compatible = "qcom,dwc3-ss-usb-phy";
reg = <0x100f8830 0x30>;
clocks = <&gcc USB30_1_MASTER_CLK>;
clock-names = "ref";
#phy-cells = <0>;
status = "disabled";
};
hs_phy_0: phy@110f8800 {
compatible = "qcom,dwc3-hs-usb-phy";
reg = <0x110f8800 0x30>;
clocks = <&gcc USB30_0_UTMI_CLK>;
clock-names = "ref";
#phy-cells = <0>;
status = "disabled";
};
ss_phy_0: phy@110f8830 {
compatible = "qcom,dwc3-ss-usb-phy";
reg = <0x110f8830 0x30>;
clocks = <&gcc USB30_0_MASTER_CLK>;
clock-names = "ref";
#phy-cells = <0>;
status = "disabled";
};
usb3_0: usb30@0 {
compatible = "qcom,dwc3";
#address-cells = <1>;
#size-cells = <1>;
clocks = <&gcc USB30_0_MASTER_CLK>;
clock-names = "core";
ranges;
resets = <&gcc USB30_0_MASTER_RESET>;
reset-names = "usb30_0_mstr_rst";
status = "disabled";
dwc3@11000000 {
compatible = "snps,dwc3";
reg = <0x11000000 0xcd00>;
interrupts = <0 110 0x4>;
phys = <&hs_phy_0>, <&ss_phy_0>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "host";
snps,dis_u3_susphy_quirk;
};
};
usb3_1: usb30@1 {
compatible = "qcom,dwc3";
#address-cells = <1>;
#size-cells = <1>;
clocks = <&gcc USB30_1_MASTER_CLK>;
clock-names = "core";
ranges;
resets = <&gcc USB30_1_MASTER_RESET>;
reset-names = "usb30_1_mstr_rst";
status = "disabled";
dwc3@10000000 {
compatible = "snps,dwc3";
reg = <0x10000000 0xcd00>;
interrupts = <0 205 0x4>;
phys = <&hs_phy_1>, <&ss_phy_1>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "host";
snps,dis_u3_susphy_quirk;
};
};
pcie0: pci@1b500000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
interrupts = <GIC_SPI 35 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_CLK>,
<&gcc PCIE_AUX_CLK>,
<&gcc PCIE_ALT_REF_CLK>;
clock-names = "core", "iface", "phy", "aux", "ref";
assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
assigned-clock-rates = <100000000>;
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>,
<&gcc PCIE_EXT_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
pinctrl-0 = <&pcie0_pins>;
pinctrl-names = "default";
perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
phy-tx0-term-offset = <7>;
status = "disabled";
};
pcie1: pci@1b700000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b700000 0x1000
0x1b702000 0x80
0x1b800000 0x100
0x31f00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <1>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_1_A_CLK>,
<&gcc PCIE_1_H_CLK>,
<&gcc PCIE_1_PHY_CLK>,
<&gcc PCIE_1_AUX_CLK>,
<&gcc PCIE_1_ALT_REF_CLK>;
clock-names = "core", "iface", "phy", "aux", "ref";
assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
assigned-clock-rates = <100000000>;
resets = <&gcc PCIE_1_ACLK_RESET>,
<&gcc PCIE_1_HCLK_RESET>,
<&gcc PCIE_1_POR_RESET>,
<&gcc PCIE_1_PCI_RESET>,
<&gcc PCIE_1_PHY_RESET>,
<&gcc PCIE_1_EXT_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
pinctrl-0 = <&pcie1_pins>;
pinctrl-names = "default";
perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
phy-tx0-term-offset = <7>;
status = "disabled";
};
pcie2: pci@1b900000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b900000 0x1000
0x1b902000 0x80
0x1ba00000 0x100
0x35f00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <2>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_2_A_CLK>,
<&gcc PCIE_2_H_CLK>,
<&gcc PCIE_2_PHY_CLK>,
<&gcc PCIE_2_AUX_CLK>,
<&gcc PCIE_2_ALT_REF_CLK>;
clock-names = "core", "iface", "phy", "aux", "ref";
assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
assigned-clock-rates = <100000000>;
resets = <&gcc PCIE_2_ACLK_RESET>,
<&gcc PCIE_2_HCLK_RESET>,
<&gcc PCIE_2_POR_RESET>,
<&gcc PCIE_2_PCI_RESET>,
<&gcc PCIE_2_PHY_RESET>,
<&gcc PCIE_2_EXT_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
pinctrl-0 = <&pcie2_pins>;
pinctrl-names = "default";
perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
phy-tx0-term-offset = <7>;
status = "disabled";
};
adm_dma: dma@18300000 {
compatible = "qcom,adm";
reg = <0x18300000 0x100000>;
interrupts = <0 170 0>;
#dma-cells = <1>;
clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
clock-names = "core", "iface";
resets = <&gcc ADM0_RESET>,
<&gcc ADM0_PBUS_RESET>,
<&gcc ADM0_C0_RESET>,
<&gcc ADM0_C1_RESET>,
<&gcc ADM0_C2_RESET>;
reset-names = "clk", "pbus", "c0", "c1", "c2";
qcom,ee = <0>;
status = "disabled";
};
nand@1ac00000 {
compatible = "qcom,ipq806x-nand";
reg = <0x1ac00000 0x800>;
clocks = <&gcc EBI2_CLK>,
<&gcc EBI2_AON_CLK>;
clock-names = "core", "aon";
dmas = <&adm_dma 3>;
dma-names = "rxtx";
qcom,cmd-crci = <15>;
qcom,data-crci = <3>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
nss_common: syscon@03000000 {
compatible = "syscon";
reg = <0x03000000 0x0000FFFF>;
};
qsgmii_csr: syscon@1bb00000 {
compatible = "syscon";
reg = <0x1bb00000 0x000001FF>;
};
stmmac_axi_setup: stmmac-axi-config {
snps,wr_osr_lmt = <7>;
snps,rd_osr_lmt = <7>;
snps,blen = <16 0 0 0 0 0 0>;
};
gmac0: ethernet@37000000 {
device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37000000 0x200000>;
interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
snps,aal = <1>;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
clocks = <&gcc GMAC_CORE1_CLK>;
clock-names = "stmmaceth";
resets = <&gcc GMAC_CORE1_RESET>;
reset-names = "stmmaceth";
status = "disabled";
};
gmac1: ethernet@37200000 {
device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37200000 0x200000>;
interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
snps,aal = <1>;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
clocks = <&gcc GMAC_CORE2_CLK>;
clock-names = "stmmaceth";
resets = <&gcc GMAC_CORE2_RESET>;
reset-names = "stmmaceth";
status = "disabled";
};
gmac2: ethernet@37400000 {
device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37400000 0x200000>;
interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
snps,aal = <1>;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
clocks = <&gcc GMAC_CORE3_CLK>;
clock-names = "stmmaceth";
resets = <&gcc GMAC_CORE3_RESET>;
reset-names = "stmmaceth";
status = "disabled";
};
gmac3: ethernet@37600000 {
device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37600000 0x200000>;
interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
snps,axi-config = <&stmmac_axi_setup>;
snps,pbl = <32>;
snps,aal = <1>;
qcom,nss-common = <&nss_common>;
qcom,qsgmii-csr = <&qsgmii_csr>;
clocks = <&gcc GMAC_CORE4_CLK>;
clock-names = "stmmaceth";
resets = <&gcc GMAC_CORE4_RESET>;
reset-names = "stmmaceth";
status = "disabled";
};
/* Temporary fixed regulator */
vsdcc_fixed: vsdcc-regulator {
compatible = "regulator-fixed";
regulator-name = "SDCC Power";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
sdcc1bam:dma@12402000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <0 98 0>;
clocks = <&gcc SDC1_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc3bam:dma@12182000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <0 96 0>;
clocks = <&gcc SDC3_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
amba {
compatible = "arm,amba-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <8>;
max-frequency = <96000000>;
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
vmmc-supply = <&vsdcc_fixed>;
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
dma-names = "tx", "rx";
};
sdcc3: sdcc@12180000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x12180000 0x2000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <8>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <192000000>;
#mmc-ddr-1_8v;
sd-uhs-sdr104;
sd-uhs-ddr50;
vqmmc-supply = <&vsdcc_fixed>;
dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
dma-names = "tx", "rx";
};
};
};
sfpb_mutex: sfpb-mutex {
compatible = "qcom,sfpb-mutex";
syscon = <&sfpb_mutex_block 4 4>;
#hwlock-cells = <1>;
};
smem {
compatible = "qcom,smem";
memory-region = <&smem>;
hwlocks = <&sfpb_mutex 3>;
};
};