openwrt/target/linux/generic/pending-4.19/681-NET-add-of_get_mac_addr...

134 lines
3.5 KiB
Diff
Raw Normal View History

From: John Crispin <blogic@openwrt.org>
Subject: NET: add mtd-mac-address support to of_get_mac_address()
Many embedded devices have information such as mac addresses stored inside mtd
devices. This patch allows us to add a property inside a node describing a
network interface. The new property points at a mtd partition with an offset
where the mac address can be found.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/of/of_net.c | 37 +++++++++++++++++++++++++++++++++++++
include/linux/of_net.h | 1 +
2 files changed, 38 insertions(+)
--- a/drivers/of/of_net.c
+++ b/drivers/of/of_net.c
kernel: Make the patches apply on top of 4.19 This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-11-01 17:01:44 +00:00
@@ -11,6 +11,7 @@
#include <linux/of_net.h>
#include <linux/phy.h>
#include <linux/export.h>
+#include <linux/mtd/mtd.h>
/**
* of_get_phy_mode - Get phy mode for given device_node
kernel: Make the patches apply on top of 4.19 This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-11-01 17:01:44 +00:00
@@ -39,7 +40,7 @@ int of_get_phy_mode(struct device_node *
}
EXPORT_SYMBOL_GPL(of_get_phy_mode);
-static const void *of_get_mac_addr(struct device_node *np, const char *name)
+static void *of_get_mac_addr(struct device_node *np, const char *name)
{
struct property *pp = of_find_property(np, name, NULL);
kernel: Make the patches apply on top of 4.19 This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-11-01 17:01:44 +00:00
@@ -48,6 +49,79 @@ static const void *of_get_mac_addr(struc
return NULL;
}
+static const void *of_get_mac_address_mtd(struct device_node *np)
+{
+#ifdef CONFIG_MTD
+ struct device_node *mtd_np = NULL;
+ struct property *prop;
+ size_t retlen;
+ int size, ret;
+ struct mtd_info *mtd;
+ const char *part;
+ const __be32 *list;
+ phandle phandle;
+ u32 mac_inc = 0;
+ u8 mac[ETH_ALEN];
+ void *addr;
+ u32 inc_idx;
+
+ list = of_get_property(np, "mtd-mac-address", &size);
+ if (!list || (size != (2 * sizeof(*list))))
+ return NULL;
+
+ phandle = be32_to_cpup(list++);
+ if (phandle)
+ mtd_np = of_find_node_by_phandle(phandle);
+
+ if (!mtd_np)
+ return NULL;
+
+ part = of_get_property(mtd_np, "label", NULL);
+ if (!part)
+ part = mtd_np->name;
+
+ mtd = get_mtd_device_nm(part);
+ if (IS_ERR(mtd))
+ return NULL;
+
+ ret = mtd_read(mtd, be32_to_cpup(list), 6, &retlen, mac);
+ put_mtd_device(mtd);
+
+ if (of_property_read_u32(np, "mtd-mac-address-increment-byte", &inc_idx))
+ inc_idx = 5;
+ if (inc_idx > 5)
+ return NULL;
+
+ if (!of_property_read_u32(np, "mtd-mac-address-increment", &mac_inc))
+ mac[inc_idx] += mac_inc;
+
+ if (!is_valid_ether_addr(mac))
+ return NULL;
+
+ addr = of_get_mac_addr(np, "mac-address");
+ if (addr) {
+ memcpy(addr, mac, ETH_ALEN);
+ return addr;
+ }
+
+ prop = kzalloc(sizeof(*prop), GFP_KERNEL);
+ if (!prop)
+ return NULL;
+
+ prop->name = "mac-address";
+ prop->length = ETH_ALEN;
+ prop->value = kmemdup(mac, ETH_ALEN, GFP_KERNEL);
+ if (!prop->value || of_add_property(np, prop))
+ goto free;
+
+ return prop->value;
+free:
+ kfree(prop->value);
+ kfree(prop);
+#endif
+ return NULL;
+}
+
/**
* Search the device tree for the best MAC address to use. 'mac-address' is
* checked first, because that is supposed to contain to "most recent" MAC
kernel: Make the patches apply on top of 4.19 This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-11-01 17:01:44 +00:00
@@ -65,11 +139,18 @@ static const void *of_get_mac_addr(struc
* addresses. Some older U-Boots only initialized 'local-mac-address'. In
* this case, the real MAC is in 'local-mac-address', and 'mac-address' exists
* but is all zeros.
+ *
+ * If a mtd-mac-address property exists, try to fetch the MAC address from the
+ * specified mtd device, and store it as a 'mac-address' property
*/
const void *of_get_mac_address(struct device_node *np)
{
const void *addr;
+ addr = of_get_mac_address_mtd(np);
+ if (addr)
+ return addr;
+
addr = of_get_mac_addr(np, "mac-address");
if (addr)
return addr;