openwrt/target/linux/brcm2708/patches-4.1/0087-gpio-poweroff-Allow-it...

109 lines
3.8 KiB
Diff
Raw Normal View History

From 842fe412d512dabb76d169395086b6337150015a Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Thu, 25 Jun 2015 12:16:11 +0100
Subject: [PATCH 087/121] gpio-poweroff: Allow it to work on Raspberry Pi
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
---
arch/arm/boot/dts/overlays/Makefile | 1 +
arch/arm/boot/dts/overlays/README | 13 +++++++++
.../boot/dts/overlays/gpio-poweroff-overlay.dts | 34 ++++++++++++++++++++++
drivers/power/reset/gpio-poweroff.c | 4 ++-
4 files changed, 51 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts
--- a/arch/arm/boot/dts/overlays/Makefile
+++ b/arch/arm/boot/dts/overlays/Makefile
@@ -16,6 +16,7 @@ dtb-$(RPI_DT_OVERLAYS) += ads7846-overla
dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
+dtb-$(RPI_DT_OVERLAYS) += gpio-poweroff-overlay.dtb
dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb
dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb
dtb-$(RPI_DT_OVERLAYS) += hifiberry-dacplus-overlay.dtb
--- a/arch/arm/boot/dts/overlays/README
+++ b/arch/arm/boot/dts/overlays/README
@@ -192,6 +192,19 @@ Params: int_pin GPIO us
speed SPI bus speed (default 12000000)
+Name: gpio-poweroff
+Info: Drives a GPIO high or low on reboot
+Load: gpio-poweroff,<param>=<val>
+Params: gpiopin GPIO for signalling (default 26)
+
+ active_low Set if the power control device requires a
+ high->low transition to trigger a power-down.
+ Note that this will require the support of a
+ custom dt-blob.bin to prevent a power-down
+ during the boot process, and that a reboot
+ will also cause the pin to go low.
+
+
Name: hifiberry-amp
Info: Configures the HifiBerry Amp and Amp+ audio cards
Load: dtoverlay=hifiberry-amp
--- /dev/null
+++ b/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts
@@ -0,0 +1,34 @@
+// Definitions for gpio-poweroff module
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "brcm,bcm2708";
+
+ fragment@0 {
+ target-path = "/";
+ __overlay__ {
+ power_ctrl: power_ctrl {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio 26 0>;
+ force;
+ };
+ };
+ };
+
+ fragment@1 {
+ target = <&gpio>;
+ __overlay__ {
+ power_ctrl_pins: power_ctrl_pins {
+ brcm,pins = <26>;
+ brcm,function = <1>; // out
+ };
+ };
+ };
+
+ __overrides__ {
+ gpiopin = <&power_ctrl>,"gpios:4",
+ <&power_ctrl_pins>,"brcm,pins:0";
+ active_low = <&power_ctrl>,"gpios:8";
+ };
+};
--- a/drivers/power/reset/gpio-poweroff.c
+++ b/drivers/power/reset/gpio-poweroff.c
@@ -48,9 +48,11 @@ static void gpio_poweroff_do_poweroff(vo
static int gpio_poweroff_probe(struct platform_device *pdev)
{
bool input = false;
+ bool force = false;
/* If a pm_power_off function has already been added, leave it alone */
- if (pm_power_off != NULL) {
+ force = of_property_read_bool(pdev->dev.of_node, "force");
+ if (!force && (pm_power_off != NULL)) {
dev_err(&pdev->dev,
"%s: pm_power_off function already registered",
__func__);