openwrt/target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2...

162 lines
2.7 KiB
Plaintext
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
model = "ELECOM WRC-300GHBK2-I";
compatible = "elecom,wrc-300ghbk2-i", "qca,qca9563";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};
leds {
compatible = "gpio-leds";
power: power {
label = "wrc-300ghbk2-i:white:power";
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
wlan2g {
label = "wrc-300ghbk2-i:white:wlan2g";
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
wps {
label = "wrc-300ghbk2-i:red:wps";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
button_wps {
label = "wps";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
ap {
label = "ap";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
read-only;
};
partition@50000 {
label = "nvram";
reg = <0x050000 0x020000>;
read-only;
};
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x070000 0x770000>;
};
partition@7e0000 {
label = "hwconfig";
reg = <0x7e0000 0x010000>;
read-only;
};
ART: partition@7f0000 {
label = "ART";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "sgmii";
qca,ar8327-initvals = <
0x04 0x00000080 /* PORT0 PAD MODE CTRL */
0x50 0xcf37cf37 /* LED_CTRL0 */
0x54 0x00000000 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
0x5c 0x03ffff00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&ART 0x1002>;
mtd-mac-address-increment = <(-1)>;
phy-mode = "sgmii";
phy-handle = <&phy0>;
};
&uart {
status = "okay";
};
&wmac {
status = "okay";
mtd-cal-data = <&ART 0x1000>;
};