hak5
/
openwrt-owl
mirror of https://github.com/hak5/openwrt-owl.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
30,420 Commits
4 Branches
8 Tags
169 MiB
C 66.6%
Makefile 16.7%
Shell 8%
Roff 2.7%
Perl 2.1%
Other 3.8%
 
 
 
 
 
 
Go to file
John Crispin fd82ffec00 ar71xx: Hornet UB GPIO WPS/Reset 
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".

There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:

Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.

The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44692
 		2015-03-12 10:06:42 +00:00
config config: disable kernel tracing on uml 2015-02-11 11:31:26 +00:00
docs docs: update remaining references to functions.sh 2012-12-20 15:29:33 +00:00
include netfilter: fix nf_nat_redirect dependencies for 3.19 and 4.0 2015-03-05 20:24:22 +00:00
package lldpd: add support for 'readonly_mode' 2015-03-12 10:06:08 +00:00
scripts scripts: fix getver git dir check 2015-02-14 20:48:37 +00:00
target ar71xx: Hornet UB GPIO WPS/Reset 2015-03-12 10:06:42 +00:00
toolchain toolchain/gcc: fix an ICE on ARM (PR58595) 2015-02-11 11:30:56 +00:00
tools disable silent-rules by default 2015-03-12 00:39:50 +00:00
.gitattributes add .gitattributes to prevent the git autocrlf option from messing with CRLF/LF in files 2012-05-08 13:30:49 +00:00
.gitignore add git-src to .gitignore 2014-01-12 12:06:39 +00:00
BSDmakefile
…
Config.in scripts/config: sync with linux upstream 2015-01-08 14:33:53 +00:00
LICENSE
…
Makefile Revert "build: use ONESHELL to speed up scanning and the toplevel makefile" 2014-10-22 10:47:26 +00:00
README Add 'subversion' build dependency to README 2014-08-31 12:06:32 +00:00
feeds.conf.default Move telephony feed to github 2014-12-11 10:30:51 +00:00
rules.mk rules.mk: don't add staging_dir/host/bin/ path again 2015-02-10 15:49:36 +00:00

README 

This is the buildsystem for the OpenWrt Linux distribution.

Please use "make menuconfig" to configure your appreciated
configuration for the toolchain and firmware.

You need to have installed gcc, binutils, bzip2, flex, python, perl, make,
find, grep, diff, unzip, gawk, getopt, subversion, libz-dev and libc headers.

Run "./scripts/feeds update -a" to get all the latest package definitions
defined in feeds.conf / feeds.conf.default respectively
and "./scripts/feeds install -a" to install symlinks of all of them into
package/feeds/.

Use "make menuconfig" to configure your image.

Simply running "make" will build your firmware.
It will download all sources, build the cross-compile toolchain, 
the kernel and all choosen applications.

You can use "scripts/flashing/flash.sh" for remotely updating your embedded
system via tftp.

The OpenWrt system is documented in docs/. You will need a LaTeX distribution
and the tex4ht package to build the documentation. Type "make -C docs/" to build it.

To build your own firmware you need to have access to a Linux, BSD or MacOSX system
(case-sensitive filesystem required). Cygwin will not be supported because of
the lack of case sensitiveness in the file system.


Sunshine!
	Your OpenWrt Project
	http://openwrt.org