mirror of https://github.com/hak5/openwrt-owl.git
176 lines
7.8 KiB
Diff
176 lines
7.8 KiB
Diff
--- a/nl80211.h
|
|
+++ b/nl80211.h
|
|
@@ -503,6 +503,9 @@
|
|
* TX status event pertaining to the TX request.
|
|
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
|
|
* management frames at CCK rate or not in 2GHz band.
|
|
+ * %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
|
|
+ * counters which will be updated to the current value. This attribute
|
|
+ * is used during CSA period.
|
|
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
|
|
* command may be used with the corresponding cookie to cancel the wait
|
|
* time if it is known that it is no longer necessary.
|
|
@@ -1525,10 +1528,10 @@ enum nl80211_commands {
|
|
* operation).
|
|
* @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
|
|
* for the time while performing a channel switch.
|
|
- * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter
|
|
- * field in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
|
|
- * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter
|
|
- * field in the probe response (%NL80211_ATTR_PROBE_RESP).
|
|
+ * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
|
|
+ * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
|
|
+ * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
|
|
+ * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
|
|
*
|
|
* @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
|
|
* As specified in the &enum nl80211_rxmgmt_flags.
|
|
@@ -1576,9 +1579,21 @@ enum nl80211_commands {
|
|
* advertise values that cannot always be met. In such cases, an attempt
|
|
* to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
|
|
*
|
|
+ * @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which
|
|
+ * should be updated when the frame is transmitted.
|
|
+ * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
|
|
+ * supported number of csa counters.
|
|
+ *
|
|
* @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32.
|
|
* As specified in the &enum nl80211_tdls_peer_capability.
|
|
*
|
|
+ * @NL80211_ATTR_IFACE_SOCKET_OWNER: flag attribute, if set during interface
|
|
+ * creation then the new interface will be owned by the netlink socket
|
|
+ * that created it and will be destroyed when the socket is closed
|
|
+ *
|
|
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
|
|
+ * transmit power to stay within regulatory limits. u32, dBi.
|
|
+ *
|
|
* @NL80211_ATTR_MAX: highest attribute number currently defined
|
|
* @__NL80211_ATTR_AFTER_LAST: internal use
|
|
*/
|
|
@@ -1914,6 +1929,13 @@ enum nl80211_attrs {
|
|
|
|
NL80211_ATTR_TDLS_PEER_CAPABILITY,
|
|
|
|
+ NL80211_ATTR_IFACE_SOCKET_OWNER,
|
|
+
|
|
+ NL80211_ATTR_CSA_C_OFFSETS_TX,
|
|
+ NL80211_ATTR_MAX_CSA_COUNTERS,
|
|
+
|
|
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
|
|
+
|
|
/* add attributes here, update the policy in nl80211.c */
|
|
|
|
__NL80211_ATTR_AFTER_LAST,
|
|
@@ -2182,6 +2204,8 @@ enum nl80211_sta_bss_param {
|
|
* Contains a nested array of signal strength attributes (u8, dBm)
|
|
* @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
|
|
* Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
|
|
+ * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the
|
|
+ * 802.11 header (u32, kbps)
|
|
* @__NL80211_STA_INFO_AFTER_LAST: internal
|
|
* @NL80211_STA_INFO_MAX: highest possible station info attribute
|
|
*/
|
|
@@ -2213,6 +2237,7 @@ enum nl80211_sta_info {
|
|
NL80211_STA_INFO_TX_BYTES64,
|
|
NL80211_STA_INFO_CHAIN_SIGNAL,
|
|
NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
|
|
+ NL80211_STA_INFO_EXPECTED_THROUGHPUT,
|
|
|
|
/* keep last */
|
|
__NL80211_STA_INFO_AFTER_LAST,
|
|
@@ -2336,9 +2361,34 @@ enum nl80211_band_attr {
|
|
* using this channel as the primary or any of the secondary channels
|
|
* isn't possible
|
|
* @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
|
|
+ * @NL80211_FREQUENCY_ATTR_INDOOR_ONLY: Only indoor use is permitted on this
|
|
+ * channel. A channel that has the INDOOR_ONLY attribute can only be
|
|
+ * used when there is a clear assessment that the device is operating in
|
|
+ * an indoor surroundings, i.e., it is connected to AC power (and not
|
|
+ * through portable DC inverters) or is under the control of a master
|
|
+ * that is acting as an AP and is connected to AC power.
|
|
+ * @NL80211_FREQUENCY_ATTR_GO_CONCURRENT: GO operation is allowed on this
|
|
+ * channel if it's connected concurrently to a BSS on the same channel on
|
|
+ * the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
|
|
+ * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO on a
|
|
+ * channel that has the GO_CONCURRENT attribute set can be done when there
|
|
+ * is a clear assessment that the device is operating under the guidance of
|
|
+ * an authorized master, i.e., setting up a GO while the device is also
|
|
+ * connected to an AP with DFS and radar detection on the UNII band (it is
|
|
+ * up to user-space, i.e., wpa_supplicant to perform the required
|
|
+ * verifications)
|
|
+ * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
|
|
+ * on this channel in current regulatory domain.
|
|
+ * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
|
|
+ * on this channel in current regulatory domain.
|
|
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
|
|
* currently defined
|
|
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
|
|
+ *
|
|
+ * See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
|
|
+ * for more information on the FCC description of the relaxations allowed
|
|
+ * by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
|
|
+ * NL80211_FREQUENCY_ATTR_GO_CONCURRENT.
|
|
*/
|
|
enum nl80211_frequency_attr {
|
|
__NL80211_FREQUENCY_ATTR_INVALID,
|
|
@@ -2355,6 +2405,10 @@ enum nl80211_frequency_attr {
|
|
NL80211_FREQUENCY_ATTR_NO_80MHZ,
|
|
NL80211_FREQUENCY_ATTR_NO_160MHZ,
|
|
NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
|
|
+ NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
|
|
+ NL80211_FREQUENCY_ATTR_GO_CONCURRENT,
|
|
+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
|
|
+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
|
|
|
|
/* keep last */
|
|
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
|
|
@@ -2573,10 +2627,13 @@ enum nl80211_dfs_regions {
|
|
* present has been registered with the wireless core that
|
|
* has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
|
|
* supported feature.
|
|
+ * @NL80211_USER_REG_HINT_INDOOR: a user sent an hint indicating that the
|
|
+ * platform is operating in an indoor environment.
|
|
*/
|
|
enum nl80211_user_reg_hint_type {
|
|
NL80211_USER_REG_HINT_USER = 0,
|
|
NL80211_USER_REG_HINT_CELL_BASE = 1,
|
|
+ NL80211_USER_REG_HINT_INDOOR = 2,
|
|
};
|
|
|
|
/**
|
|
@@ -3650,6 +3707,8 @@ enum nl80211_iface_limit_attrs {
|
|
* different channels may be used within this group.
|
|
* @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
|
|
* of supported channel widths for radar detection.
|
|
+ * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
|
|
+ * of supported regulatory regions for radar detection.
|
|
* @NUM_NL80211_IFACE_COMB: number of attributes
|
|
* @MAX_NL80211_IFACE_COMB: highest attribute number
|
|
*
|
|
@@ -3683,6 +3742,7 @@ enum nl80211_if_combination_attrs {
|
|
NL80211_IFACE_COMB_STA_AP_BI_MATCH,
|
|
NL80211_IFACE_COMB_NUM_CHANNELS,
|
|
NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
|
|
+ NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
|
|
|
|
/* keep last */
|
|
NUM_NL80211_IFACE_COMB,
|
|
@@ -3893,6 +3953,9 @@ enum nl80211_ap_sme_features {
|
|
* interface. An active monitor interface behaves like a normal monitor
|
|
* interface, but gets added to the driver. It ensures that incoming
|
|
* unicast packets directed at the configured interface address get ACKed.
|
|
+ * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
|
|
+ * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
|
|
+ * lifetime of a BSS.
|
|
*/
|
|
enum nl80211_feature_flags {
|
|
NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
|
|
@@ -3913,6 +3976,7 @@ enum nl80211_feature_flags {
|
|
NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
|
|
NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
|
|
NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
|
|
+ NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
|
|
};
|
|
|
|
/**
|