openwrt-owl

Go to file

Gabor Juhos b3fdd931d1 ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boards This patch adds support for the Sitecom WL-341 v3 and other Sercomm IP1006RRv2 based boards for sysupgrade support and for the initial flash through pushbutton initiated recovery mode with the special partition table and fixes for the quirks and things required by the modified bootloader. There is a known bug, Wi-Fi is not working on my board probably because of the lack of RAM (the board only has 16MiB ram -- half of the normal amount for non rebadged versions, but there is an empty slot for another ram chip,) but I don't know for sure. The driver loads but hostapd fails to load so I think it's not related to the specific device except for the lack of RAM. Moreover, only 7 of the 11 onboard leds are confirmed working, it seems that one of the others is always on and the remaining ones are connected to the wireless card leds already recognized by OpenWrt [juhosg: reordered some parts in order to keep things sorted alphabetically] Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com> SVN-Revision: 29910		2012-01-26 10:44:23 +00:00
docs	kamikaze has been released long ago	2011-02-11 14:04:00 +00:00
include	autotools.mk: fix autoreconf in subdirectories, thanks field_it for spotting this	2012-01-20 21:31:03 +00:00
package	mac80211: enable support for RaLink Rt53xx USB devices in rt2800usb	2012-01-25 07:44:46 +00:00
scripts	ext-toolchain.sh: CONFIG_NLS -> CONFIG_BUILD_NLS	2012-01-19 00:03:52 +00:00
target	ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boards	2012-01-26 10:44:23 +00:00
toolchain	eglibc 2.14 needs our eglibc patchset as well	2012-01-21 19:39:37 +00:00
tools	libtool: fix accidental sed invocation in libtoolize	2012-01-21 09:49:53 +00:00
.gitignore	.gitignore: Ignore Emacs editor generated files	2011-10-31 09:37:59 +00:00
BSDmakefile	add missing copyright header	2007-02-26 01:05:09 +00:00
Config.in	if CONFIG_BUILD_NLS is selected, compile uClibc with locale support	2012-01-01 15:11:11 +00:00
LICENSE	finally move buildroot-ng to trunk	2016-03-20 17:29:15 +01:00
Makefile	abort built in prereq target if there is no site config file for the current target	2012-01-19 12:19:28 +00:00
README	trying to make README file a bit more helpful	2012-01-21 01:15:24 +00:00
feeds.conf.default	Add xorg feed to feeds.conf.default	2011-11-16 16:05:23 +00:00
rules.mk	use ext-toolchain.sh to integrate external toolchains Use ext-toolchain.sh to wrap external toolchain commands, abort build if certain features such as CONFIG_SOFT_FLOAT or CONFIG_IPV6 are enabled but not supported by the toolchain.	2012-01-18 03:08:09 +00:00

README

This is the buildsystem for the OpenWrt Linux distribution.

Please use "make menuconfig" to configure your appreciated
configuration for the toolchain and firmware.

You need to have installed gcc, binutils, patch, bzip2, flex,
make, gettext, pkg-config, unzip, libz-dev and libc headers.

Run "./scripts/feeds update" to get the latest package definitions
defined in feeds.conf / feeds.conf.default respectively
and "./scripts/feeds install" to install symlinks into "package/feeds/*".

Use "make menuconfig" to configure your image.

Simply running "make" will build your firmware.
It will download all sources, build the cross-compile toolchain, 
the kernel and all choosen applications.

You can use "scripts/flashing/flash.sh" for remotely updating your embedded
system via tftp.

The OpenWrt system is documented in docs/. You will need a LaTeX distribution
and the tex4ht package to build the documentation. Type "make -C docs/" to build it.

To build your own firmware you need to have access to a Linux, BSD or MacOSX system
(case-sensitive filesystem required). Cygwin will not be supported because of
the lack of case sensitiveness in the file system.


Sunshine!
	Your OpenWrt Project
	http://openwrt.org