openwrt-owl/package/boot/uboot-oxnas/files/drivers/usb/host/ehci-oxnas.c

106 lines
3.0 KiB
C

/*
* drivers/usb/host/ehci-oxnas.c
*
* Tzachi Perelstein <tzachi@marvell.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <common.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sysctl.h>
#include <asm/arch/clock.h>
#include "ehci.h"
static struct ehci_hcor *ghcor;
static int start_oxnas_usb_ehci(void)
{
#ifdef CONFIG_USB_PLLB_CLK
reset_block(SYS_CTRL_RST_PLLB, 0);
enable_clock(SYS_CTRL_CLK_REF600);
writel((1 << PLLB_ENSAT) | (1 << PLLB_OUTDIV) | (2 << PLLB_REFDIV),
SEC_CTRL_PLLB_CTRL0);
/* 600MHz pllb divider for 12MHz */
writel(PLLB_DIV_INT(50) | PLLB_DIV_FRAC(0), SEC_CTRL_PLLB_DIV_CTRL);
#else
/* ref 300 divider for 12MHz */
writel(REF300_DIV_INT(25) | REF300_DIV_FRAC(0), SYS_CTRL_REF300_DIV);
#endif
/* Ensure the USB block is properly reset */
reset_block(SYS_CTRL_RST_USBHS, 1);
reset_block(SYS_CTRL_RST_USBHS, 0);
reset_block(SYS_CTRL_RST_USBHSPHYA, 1);
reset_block(SYS_CTRL_RST_USBHSPHYA, 0);
reset_block(SYS_CTRL_RST_USBHSPHYB, 1);
reset_block(SYS_CTRL_RST_USBHSPHYB, 0);
/* Force the high speed clock to be generated all the time, via serial
programming of the USB HS PHY */
writel((2UL << USBHSPHY_TEST_ADD) |
(0xe0UL << USBHSPHY_TEST_DIN), SYS_CTRL_USBHSPHY_CTRL);
writel((1UL << USBHSPHY_TEST_CLK) |
(2UL << USBHSPHY_TEST_ADD) |
(0xe0UL << USBHSPHY_TEST_DIN), SYS_CTRL_USBHSPHY_CTRL);
writel((0xfUL << USBHSPHY_TEST_ADD) |
(0xaaUL << USBHSPHY_TEST_DIN), SYS_CTRL_USBHSPHY_CTRL);
writel((1UL << USBHSPHY_TEST_CLK) |
(0xfUL << USBHSPHY_TEST_ADD) |
(0xaaUL << USBHSPHY_TEST_DIN), SYS_CTRL_USBHSPHY_CTRL);
#ifdef CONFIG_USB_PLLB_CLK /* use pllb clock */
writel(USB_CLK_INTERNAL | USB_INT_CLK_PLLB, SYS_CTRL_USB_CTRL);
#else /* use ref300 derived clock */
writel(USB_CLK_INTERNAL | USB_INT_CLK_REF300, SYS_CTRL_USB_CTRL);
#endif
/* Enable the clock to the USB block */
enable_clock(SYS_CTRL_CLK_USBHS);
return 0;
}
int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr,
struct ehci_hcor **hcor)
{
start_oxnas_usb_ehci();
*hccr = (struct ehci_hccr *)(USB_HOST_BASE + 0x100);
*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
ghcor = *hcor;
return 0;
}
int ehci_hcd_stop(int index)
{
reset_block(SYS_CTRL_RST_USBHS, 1);
disable_clock(SYS_CTRL_CLK_USBHS);
return 0;
}
extern void __ehci_set_usbmode(int index);
void ehci_set_usbmode(int index)
{
#define or_txttfill_tuning _reserved_1_[0]
u32 tmp;
__ehci_set_usbmode(index);
tmp = ehci_readl(&ghcor->or_txfilltuning);
tmp &= ~0x00ff0000;
tmp |= 0x003f0000; /* set burst pre load count to 0x40 (63 * 4 bytes) */
tmp |= 0x16; /* set sheduler overhead to 22 * 1.267us (HS) or 22 * 6.33us (FS/LS)*/
ehci_writel(&ghcor->or_txfilltuning, tmp);
tmp = ehci_readl(&ghcor->or_txttfill_tuning);
tmp |= 0x2; /* set sheduler overhead to 2 * 6.333us */
ehci_writel(&ghcor->or_txttfill_tuning, tmp);
}