mirror of https://github.com/hak5/openwrt-owl.git
426 lines
7.6 KiB
Plaintext
426 lines
7.6 KiB
Plaintext
#include "qcom-ipq8064-v1.0.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "TP-Link Archer VR2600v";
|
|
compatible = "tplink,vr2600v", "qcom,ipq8064";
|
|
|
|
memory@0 {
|
|
reg = <0x42000000 0x1e000000>;
|
|
device_type = "memory";
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
rsvd@41200000 {
|
|
reg = <0x41200000 0x300000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
serial0 = &uart4;
|
|
mdio-gpio0 = &mdio0;
|
|
|
|
led-boot = &power;
|
|
led-failsafe = &general;
|
|
led-running = &power;
|
|
led-upgrade = &general;
|
|
};
|
|
|
|
chosen {
|
|
linux,stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
soc {
|
|
pinmux@800000 {
|
|
led_pins: led_pins {
|
|
mux {
|
|
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
|
|
"gpio26", "gpio53", "gpio56", "gpio66";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
i2c4_pins: i2c4_pinmux {
|
|
mux {
|
|
pins = "gpio12", "gpio13";
|
|
function = "gsbi4";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
button_pins: button_pins {
|
|
mux {
|
|
pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
spi_pins: spi_pins {
|
|
mux {
|
|
pins = "gpio18", "gpio19", "gpio21";
|
|
function = "gsbi5";
|
|
bias-pull-down;
|
|
};
|
|
|
|
data {
|
|
pins = "gpio18", "gpio19";
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
cs {
|
|
pins = "gpio20";
|
|
drive-strength = <10>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
clk {
|
|
pins = "gpio21";
|
|
drive-strength = <12>;
|
|
};
|
|
};
|
|
|
|
mdio0_pins: mdio0_pins {
|
|
mux {
|
|
pins = "gpio0", "gpio1";
|
|
function = "gpio";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
rgmii2_pins: rgmii2_pins {
|
|
mux {
|
|
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
|
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
|
function = "rgmii2";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
gsbi@16300000 {
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
status = "ok";
|
|
serial@16340000 {
|
|
status = "ok";
|
|
};
|
|
/*
|
|
* The i2c device on gsbi4 should not be enabled.
|
|
* On ipq806x designs gsbi4 i2c is meant for exclusive
|
|
* RPM usage. Turning this on in kernel manifests as
|
|
* i2c failure for the RPM.
|
|
*/
|
|
};
|
|
|
|
gsbi5: gsbi@1a200000 {
|
|
qcom,mode = <GSBI_PROT_SPI>;
|
|
status = "ok";
|
|
|
|
spi4: spi@1a280000 {
|
|
status = "ok";
|
|
|
|
pinctrl-0 = <&spi_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
|
|
|
flash: W25Q128@0 {
|
|
compatible = "jedec,spi-nor";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
SBL1@0 {
|
|
label = "SBL1";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
MIBIB@20000 {
|
|
label = "MIBIB";
|
|
reg = <0x20000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL2@40000 {
|
|
label = "SBL2";
|
|
reg = <0x40000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL3@80000 {
|
|
label = "SBL3";
|
|
reg = <0x80000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
DDRCONFIG@100000 {
|
|
label = "DDRCONFIG";
|
|
reg = <0x100000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
SSD@110000 {
|
|
label = "SSD";
|
|
reg = <0x110000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
TZ@120000 {
|
|
label = "TZ";
|
|
reg = <0x120000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
RPM@1a0000 {
|
|
label = "RPM";
|
|
reg = <0x1a0000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBL@220000 {
|
|
label = "APPSBL";
|
|
reg = <0x220000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBLENV@2a0000 {
|
|
label = "APPSBLENV";
|
|
reg = <0x2a0000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
OLDART@2e0000 {
|
|
label = "OLDART";
|
|
reg = <0x2e0000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
kernel@320000 {
|
|
label = "kernel";
|
|
reg = <0x320000 0x200000>;
|
|
};
|
|
|
|
rootfs@520000 {
|
|
label = "rootfs";
|
|
reg = <0x520000 0xa60000>;
|
|
};
|
|
|
|
defaultmac: default-mac@0xfaf100 {
|
|
label = "default-mac";
|
|
reg = <0xfaf100 0x00200>;
|
|
read-only;
|
|
};
|
|
|
|
ART@fc0000 {
|
|
label = "ART";
|
|
reg = <0xfc0000 0x40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
phy@100f8800 { /* USB3 port 1 HS phy */
|
|
status = "ok";
|
|
};
|
|
|
|
phy@100f8830 { /* USB3 port 1 SS phy */
|
|
status = "ok";
|
|
};
|
|
|
|
phy@110f8800 { /* USB3 port 0 HS phy */
|
|
status = "ok";
|
|
};
|
|
|
|
phy@110f8830 { /* USB3 port 0 SS phy */
|
|
status = "ok";
|
|
};
|
|
|
|
usb30@0 {
|
|
status = "ok";
|
|
};
|
|
|
|
usb30@1 {
|
|
status = "ok";
|
|
};
|
|
|
|
pcie0: pci@1b500000 {
|
|
status = "ok";
|
|
phy-tx0-term-offset = <7>;
|
|
};
|
|
|
|
pcie1: pci@1b700000 {
|
|
status = "ok";
|
|
phy-tx0-term-offset = <7>;
|
|
};
|
|
|
|
mdio0: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-0 = <&mdio0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
device_type = "ethernet-phy";
|
|
reg = <0>;
|
|
qca,ar8327-initvals = <
|
|
0x00004 0x7600000 /* PAD0_MODE */
|
|
0x00008 0x1000000 /* PAD5_MODE */
|
|
0x0000c 0x80 /* PAD6_MODE */
|
|
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
|
0x000e0 0xc74164de /* SGMII_CTRL */
|
|
0x0007c 0x4e /* PORT0_STATUS */
|
|
0x00094 0x4e /* PORT6_STATUS */
|
|
>;
|
|
};
|
|
|
|
phy4: ethernet-phy@4 {
|
|
device_type = "ethernet-phy";
|
|
reg = <4>;
|
|
};
|
|
};
|
|
|
|
gmac1: ethernet@37200000 {
|
|
status = "ok";
|
|
phy-mode = "rgmii";
|
|
qcom,id = <1>;
|
|
|
|
pinctrl-0 = <&rgmii2_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
mtd-mac-address = <&defaultmac 0>;
|
|
mtd-mac-address-increment = <1>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
gmac2: ethernet@37400000 {
|
|
status = "ok";
|
|
phy-mode = "sgmii";
|
|
qcom,id = <2>;
|
|
|
|
mtd-mac-address = <&defaultmac 0>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
rpm@108000 {
|
|
pinctrl-0 = <&i2c4_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
pinctrl-0 = <&button_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
wifi {
|
|
label = "wifi";
|
|
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RFKILL>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
dect {
|
|
label = "dect";
|
|
gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_PHONE>;
|
|
};
|
|
|
|
ledswitch {
|
|
label = "ledswitch";
|
|
gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_LIGHTS_TOGGLE>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&led_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
dsl {
|
|
label = "vr2600v:white:dsl";
|
|
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
usb {
|
|
label = "vr2600v:white:usb";
|
|
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
lan {
|
|
label = "vr2600v:white:lan";
|
|
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wlan2g {
|
|
label = "vr2600v:white:wlan2g";
|
|
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "vr2600v:white:wlan5g";
|
|
gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
power: power {
|
|
label = "vr2600v:white:power";
|
|
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
|
|
phone {
|
|
label = "vr2600v:white:phone";
|
|
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wan {
|
|
label = "vr2600v:white:wan";
|
|
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
general: general {
|
|
label = "vr2600v:white:general";
|
|
gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&adm_dma {
|
|
status = "ok";
|
|
};
|