openwrt-owl/target/linux/lantiq/image/ARV752DPW.dts

220 lines
3.7 KiB
Plaintext

/dts-v1/;
/include/ "danube.dtsi"
/ {
model = "ARV752DPW - Arcor 802";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
gpios = <&gpiomm 1 0>;
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x800000>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x10000>;
read-only;
};
partition@10000 {
label = "uboot_env";
reg = <0x10000 0x10000>;
read-only;
};
partition@20000 {
label = "linux";
reg = <0x20000 0x7d0000>;
};
partition@7f0000 {
label = "board_config";
reg = <0x7f0000 0x10000>;
read-only;
};
};
mac_addr {
compatible = "lantiq,eth-mac";
reg = <0 0x7f0016 0x6>;
mac-increment = <2>;
};
gpiomm: gpiomm@4000000 {
compatible = "lantiq,gpio-mm";
reg = <1 0x0 0x10 >;
#address-cells = <1>;
#size-cells = <1>;
#gpio-cells = <2>;
gpio-controller;
lantiq,shadow = <0x3>;
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ebu {
lantiq,groups = "ebu cs1";
lantiq,function = "ebu";
};
exin {
lantiq,groups = "exin1";
lantiq,function = "exin";
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_in {
lantiq,groups = "req2", "req1";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
leds {
lantiq,pins = "io3", "io5", "io6", "io8";
lantiq,output = <1>;
lantiq,pull = <0>;
};
keys {
lantiq,pins = "io11", "io12", "io13", "io28";
lantiq,output = <0>;
lantiq,pull = <2>;
lantiq,open-drain = <1>;
};
};
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpiomm 0 0>;
};
etop@E180000 {
phy-mode = "rmii";
};
pci@E105400 {
status = "okay";
lantiq,external-clock;
gpio-reset = <&gpio 21 0>;
interrupt-map = <0x7000 0 0 1 &icu0 135>;
req-mask = <0x3>;
};
};
ralink_eep {
compatible = "ralink,eeprom";
ralink,eeprom = "RT2860.eeprom";
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
/* wps {
label = "wps";
gpios = <&gpio 11 1>;
linux,code = <0x211>;
};*/
restart {
label = "restart";
gpios = <&gpio 12 0>;
linux,code = <0x110>;
};
dsl {
label = "dsl";
gpios = <&gpio 13 0>;
linux,code = <0x111>;
};
reset {
label = "reset";
gpios = <&gpio 28 0>;
linux,code = <0x198>;
};
};
gpio-leds {
compatible = "gpio-leds";
power {
label = "power";
gpios = <&gpio 3 1>;
};
message {
label = "message";
gpios = <&gpio 5 1>;
};
power1 {
label = "power1";
gpios = <&gpio 6 1>;
};
voice1 {
label = "voice1";
gpios = <&gpio 8 1>;
};
microphone {
/* use this led as te usb led */
label = "usb";
gpios = <&gpiomm 3 1>;
};
wifi {
label = "wifi";
gpios = <&gpiomm 4 1>;
};
fxs1 {
label = "fxs1";
gpios = <&gpiomm 5 1>;
};
fx2 {
label = "fxs2";
gpios = <&gpiomm 6 1>;
};
fxo {
label = "fxo";
gpios = <&gpiomm 7 1>;
};
internet {
label = "internet";
gpios = <&gpiomm 8 1>;
};
voice2 {
label = "voice2";
gpios = <&gpiomm 9 1>;
};
};
};