86013d40d5
ar71xx: remove the built-in MTD map of the ALL0258N
...
Pass the mtd_layout via the kernel command line instead.
Also increase the kernel partition size to 1024k, so current kernel can fit in.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32585
2012-07-03 15:24:01 +00:00
8b9931fd27
ar71xx: add support for the TL-WDR4300 board
...
SVN-Revision: 32459
2012-06-19 11:51:17 +00:00
f509a87f2d
ar71xx: remove superfluous include of asm/mach-ath79/pci.h
...
SVN-Revision: 32455
2012-06-19 10:13:43 +00:00
1a1121158f
ar71xx: add a common function to configure USB power GPIOs
...
SVN-Revision: 32454
2012-06-19 10:13:41 +00:00
26cf21df02
ar71xx: add support for the embeddedwireless Dorin board (based on patch by embeddedwireless.de)
...
SVN-Revision: 32447
2012-06-19 00:22:04 +00:00
dddf321b6e
ar71xx: swap the PHY address of the ethernet port of TL-MR3040/TL-MR11U similar to TL-MR3020 to fix ethernet link detection
...
SVN-Revision: 32336
2012-06-13 12:54:22 +00:00
73b8805e78
ar71xx: fix PHY setup on TL-MR3020 ( fixes #11572 )
...
SVN-Revision: 32093
2012-06-06 17:24:12 +00:00
dc9675282e
ar71xx: add a helper function for setting up PHY4 swapping on ar933x
...
SVN-Revision: 32092
2012-06-06 17:24:09 +00:00
8039a1bbb2
ar71xx: fix MII clock settings for various chips, improves ethernet stability on AR934x
...
SVN-Revision: 31925
2012-05-27 21:02:41 +00:00
013f434f5b
ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnD
...
Patch by Kamil Trzciński <ayufan@osk-net.pl>
SVN-Revision: 31846
2012-05-23 21:05:25 +00:00
ab897ab04e
ar71xx: add support for the TP-Link TL-WR1041N v2 board
...
Patch-by: Vince Huang <axishero@foxmail.com>
SVN-Revision: 31608
2012-05-05 17:02:35 +00:00
3e3a4d3d6b
ar71xx: allow to disable link polling on unused PHYs
...
SVN-Revision: 31533
2012-04-29 18:29:24 +00:00
408de85883
ar71xx: use ap91_pci_init for RB751{,G}
...
SVN-Revision: 31356
2012-04-19 21:31:48 +00:00
0a9832b50d
ar71xx: move USB device registration directly into rb751{,g}_setup
...
SVN-Revision: 31355
2012-04-19 21:31:43 +00:00
78967e6640
ar71xx: add ap9x_pci_get_wmac_data helper
...
SVN-Revision: 31354
2012-04-19 21:31:42 +00:00
5c9ca38e47
ar71xx: add sanity checks to decode_rle
...
Also use -EINVAL instead of -1.
SVN-Revision: 31353
2012-04-19 21:31:40 +00:00
e295a077ce
ar71xx: initial support for Mikrotik RB751G-2HnD and RB751U-2HnD
...
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
SVN-Revision: 31208
2012-04-06 06:45:07 +00:00
b77217d963
ar71xx: boost SPI flash read performance
...
mtd_speedtest results:
page read speed
old new delta
DB120 929 KiB/s 2597 KiB/s +179.55%
TL-WR1043ND v1 754 KiB/s 2166 KiB/s +187.27%
TL-WR703N v1 745 KiB/s 2176 KiB/s +192.08%
TL-MR3220 v1 752 KiB/s 2154 KiB/s +186.44%
TL-WR2543ND v1 564 KiB/s 2130 KiB/s +277.66%
TL-WR741ND v2 525 KiB/s 1767 KiB/s +236.57%
ALFA-AP96 702 KiB/s 1977 KiB/s +181.62%
WNDR3700 697 KiB/s 1965 KiB/s +181.92%
SVN-Revision: 31118
2012-03-27 19:38:17 +00:00
6cd5fb7001
ar71xx: remove the built-in MTD map of the AP96 board
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31112
2012-03-27 19:38:07 +00:00
61ee283899
ar71xx: remove the built-in MTD map of the PB92 board
...
Pass the mtd_layout via the kernel command line instead
SVN-Revision: 31111
2012-03-27 19:38:05 +00:00
1094dc1996
ar71xx: remove the built-in MTD map of the Zcomax devices
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31110
2012-03-27 19:38:04 +00:00
87e4ec687b
ar71xx: remove the built-in MTD maps of several boards
...
We are passing the MTD layout via the kernel command line, so
it makes no sense to duplicate it in mach-* files. The patch
removes the built-in MTD maps of the following boards:
* AP113
* ALFA N2/N5
* DIR-600
* DIR-615
* DIR-825
* TEW-6{3,5}2BRP
* TEW-673GRU
* WHR-G301N
* WHR-HP-GN
* WHR-HP-G300N
SVN-Revision: 31108
2012-03-27 19:38:01 +00:00
f4d1e3d147
ar71xx: fix button polarity on TL-WR703N and TL-WR741N v4
...
SVN-Revision: 31102
2012-03-27 19:37:51 +00:00
8a2e4b49de
ar71xx: add initial support for RB750GL
...
SVN-Revision: 31025
2012-03-19 15:57:04 +00:00
d19f3dd512
ar71xx: make rb750_latch_change 'static void'
...
SVN-Revision: 31024
2012-03-19 15:57:03 +00:00
5348f46c80
ar71xx: add latch_change field to rb750_led_platform_data
...
SVN-Revision: 31023
2012-03-19 15:57:01 +00:00
8a471efe01
ar71xx: add platform data for the RB750 NAND driver
...
SVN-Revision: 31022
2012-03-19 15:56:59 +00:00
e9b45ebaba
ar71xx: add AR934x specific interface speed setup for ge0
...
SVN-Revision: 31017
2012-03-19 11:11:20 +00:00
6036151187
ar71xx: add support for the jjPlus JA76PF2 board
...
SVN-Revision: 30957
2012-03-16 18:00:34 +00:00
a680662391
ar71xx: change LED name prefix on the jjplus boards
...
SVN-Revision: 30956
2012-03-16 18:00:26 +00:00
1c5ac02a29
ar71xx: reset the switch on AR934x before ethernet device registration
...
SVN-Revision: 30922
2012-03-13 17:29:33 +00:00
66df117d1b
ar71xx: use a dummy callback for interfaces with fixed speed
...
SVN-Revision: 30913
2012-03-12 20:38:58 +00:00
8b2b37ae58
ar71xx: merge ar934x_bo_ddr_flush patch
...
SVN-Revision: 30912
2012-03-12 20:38:57 +00:00
2d89fa7f43
ar71xx: fix WPS button polarity on TL-WR2543N
...
SVN-Revision: 30849
2012-03-07 19:50:53 +00:00
d72bde99cd
ar71xx: merge files-3.2 to files
...
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
386cbfe45b
ar71xx: move arch specific files to files-2.6.39
...
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
ef1c53b7b7
ar71xx: change board id of the UniFi board
...
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
fbf81c8e79
ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
...
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
12dae96097
ar71xx: fix a compiler warning
...
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
5ae0fd802c
ar71xx: fix GPIO count for AR934x
...
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
e52269364a
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
3104d70552
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
42e8ae09b5
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
c15caea360
ar71xx: add an irq parameter for ar724x_pcibios_init
...
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
cf90b24bb9
ar71xx: remove hardwired interface parameters from mach-* files
...
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
defc79cb40
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
6f4bc1ce37
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
368bbc510b
ar71xx: enable has_gbit flag on AR724{0,1}
...
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
15d7016c9f
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
f623066e60
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
d0db89133c
ar71xx: remove mii_ctrl resources of the ethernet devices
...
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
538a9493b9
ar71xx: set MII interface speed from the set_speed callbacks
...
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
93cd46be13
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
9579bb4267
ar71xx: ag71xx: remove MII interface setup code
...
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
da64ce8603
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
5ad763075e
ar71xx: use the button for WPS control on the DB120
...
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
4555be2bec
ar71xx: register the second ethernet interface on the DB120 board
...
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
368c6605a0
ar71xx: implement SoC specific phy interface setup
...
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
21d317b9cc
ar71xx: move phy interface setup into a separate function
...
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
aff0c84ffa
ar71xx: register both MDIO bus on the DB120 board
...
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
b144249108
ar71xx: add AR934X specific MDIO registration code
...
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
f835106c8c
ar71xx: add a secondary mdio bus
...
SVN-Revision: 28984
2011-11-12 12:09:54 +00:00
90a42da270
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
SVN-Revision: 28983
2011-11-12 12:09:50 +00:00
9daa2149fd
ar71xx: add an id argument to ar71xx_add_device_mdio
...
SVN-Revision: 28982
2011-11-12 12:09:48 +00:00
b07b687aec
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
SVN-Revision: 28981
2011-11-12 12:09:42 +00:00
a9216bb76e
ar71xx: add AR934x specific USB setup
...
SVN-Revision: 28980
2011-11-12 10:54:20 +00:00
346e44105a
ar71xx: register the first ethernet interface on the DB120 board
...
SVN-Revision: 28979
2011-11-12 10:54:18 +00:00
b1ba5e2f3d
ar71xx: allow to register ethernet interfaces for AR934X
...
SVN-Revision: 28978
2011-11-12 10:54:17 +00:00
e962b07c8b
ar71xx: add AR934X specific bootstrap and reset register bits
...
SVN-Revision: 28976
2011-11-12 10:54:15 +00:00
d8db8e94c8
ar71xx: fix GPIO direction setup for AR934x
...
SVN-Revision: 28974
2011-11-12 10:54:09 +00:00
43e993e5f5
ar71xx: fix AR934X clock frequency calculation
...
SVN-Revision: 28973
2011-11-12 10:54:08 +00:00
a801d620a7
ar71xx: add support for the Buffalo WHR-HP-GN board
...
SVN-Revision: 28805
2011-11-07 12:59:10 +00:00
4509af17ed
ar71xx: add support for the Buffalo WHR-G301N board
...
SVN-Revision: 28803
2011-11-07 12:59:07 +00:00
4aace1e2e3
ar71xx: fix WHR-HP-G300N MTD partitions
...
SVN-Revision: 28800
2011-11-07 12:59:03 +00:00
4c985724af
ar71xx: add missing AR71XX_MACH_TL_WR741ND_V4
...
SVN-Revision: 28709
2011-11-01 14:38:12 +00:00
91f08d47c2
ar71xx: add initial support for the TL-WR741ND v4 board
...
The ethernet port LEDs are not working yet.
SVN-Revision: 28706
2011-11-01 11:20:52 +00:00
21e651c9a1
ar71xx: add AR933X GMAC register defines
...
SVN-Revision: 28705
2011-11-01 11:20:50 +00:00
f372620ffa
ar71xx: unify LED names on Planex boards
...
SVN-Revision: 28703
2011-11-01 11:20:47 +00:00
66ab406d5a
ar71xx: unify LED names on Buffalo boards
...
SVN-Revision: 28702
2011-11-01 11:20:46 +00:00
e7586959df
ar71xx: unify LED names on TP-Link boards
...
SVN-Revision: 28701
2011-11-01 11:20:44 +00:00
1646346798
ar71xx: add initial support for the OpenMesh OM2P board
...
Based on a patch by Marek Lindner <marek@open-mesh.com>
SVN-Revision: 28617
2011-10-27 07:54:51 +00:00
d02f22fea1
ar71xx/all0258n: fix partition layout
...
A miscalculation in the original patch makes OpenWrt destroy the failsafe image.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28615
2011-10-27 07:54:47 +00:00
9d51cda2db
ar71xx: Buffalo WHR-HP-G300N kernel support
...
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 28567
2011-10-24 21:49:26 +00:00
d96e321bd1
ar71xx: add kernel support for the Allnet ALL0258N board
...
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28564
2011-10-24 21:49:21 +00:00
a136b67604
linux: ar71xx: add support for Mikrotik Routerboard RB493G
...
SVN-Revision: 28423
2011-10-11 23:05:16 +00:00
6ac4156136
ar71xx: fix MAC addresses on the DIR-825-B1 board
...
Patch-by: Lukas Kuna
SVN-Revision: 28295
2011-09-23 19:56:39 +00:00
733399600f
ar71xx: add support for the TP-Link TL-WR703N v1 board
...
Based on a patch by dongyuqi <729650915@qq.com>
SVN-Revision: 28277
2011-09-21 11:47:53 +00:00
d3617ac7d3
ar71xx: add AR933x specific USB setup function
...
SVN-Revision: 28276
2011-09-21 11:47:51 +00:00
91340d8af7
ar71xx: add ar71xx_device_reset_rmw helper
...
SVN-Revision: 28275
2011-09-21 11:47:50 +00:00
079e746fc4
ar71xx: remove 'default [yn]' from machine Kconfig entries
...
SVN-Revision: 28273
2011-09-21 11:47:47 +00:00
73dac07c44
ar71xx: sort AR71XX_MACH_* entries
...
SVN-Revision: 28272
2011-09-21 11:47:45 +00:00
65d809ef19
ar71xx: do not count normal interrupts as spurious ( fixes #10037 )
...
SVN-Revision: 28182
2011-09-06 05:38:23 +00:00
cd2c68501c
ar71xx: fix ethernet PLL setting on ar7242
...
SVN-Revision: 28124
2011-08-29 21:23:46 +00:00
12c84f8eeb
ar71xx: add some code to detect DMA stuck conditions on ar7240
...
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
d26bb6c59c
ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image layout ( fixes #9922 )
...
SVN-Revision: 27959
2011-08-11 13:52:40 +00:00
e18ceb1dac
ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NH
...
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.
SVN-Revision: 27814
2011-07-28 11:57:51 +00:00
9e4113b493
ar71xx: autodetect rtl8366s/rtl8366rb on wzr-hp-g300nh
...
SVN-Revision: 27756
2011-07-24 14:40:35 +00:00
1afe8a0726
rtl8366: unify rtl8366s and rtl8366rb platform data
...
SVN-Revision: 27754
2011-07-24 14:40:23 +00:00
9105dad418
ar71xx: enable the usb power regulator on the wzr-hp-ag300h through gpio 2 ( #9684 )
...
SVN-Revision: 27739
2011-07-24 08:02:20 +00:00
fefc79f3cb
ar71xx: reset the phy in the ethernet init on ar724x
...
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
f9e4619b97
ar71xx: remove CONFIG_MTD_CONCAT ifdefs from the WZR-HP-AG300H code
...
The config option has been removed in 2.6.39.
SVN-Revision: 27320
2011-06-30 12:15:33 +00:00
d98476c6bd
ar71xx: merge 2.6.39 patches
...
Also remove the old UART driver for ar933x.
SVN-Revision: 27314
2011-06-29 08:57:37 +00:00
Gabor Juhos
Felix Fietkau
Jo-Philipp Wich
Jonas Gorski