This adds some more code for bgmac core rev 4 and it now restarts all
cores when initializing the first one on BCM4708. I am just able to
send under 100 packages and then DMA TX does not work any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38714
This pci ID is used by sprom less BCM4313 devices.
This is a backport from the mainline kernel.
This is part of #13551.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38713
The current code only allows to automatically set
root device on MTD partitions. Move the code to MTD
core to allow to use it with all MTD devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38643
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38288
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
Separate OpenWrt specific MTD options from the mainline
option by moving those into a new submenu in the kernel
configuration interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37997
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931
The 'Warning: unable to open an initial console' message
indicates an error in the rootfs. Remove the patch which
hides the warning.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37848
Linux expects that the /dev/console node is present
in the rootfs image. Create the node in initramfs,
in order to make std{in,out,err} usable even in early
init process.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37846
Fixes the following build error on ramips/rt3883:
arch/mips/pci/pci-rt3883.c:488:3: error: implicit declaration of function \
'of_pci_get_devfn' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Although the function is only used by the PCI driver
of the RT3883 SoC but at the moment but it might be
useful for other targets as well.
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37826
vsnprintf returns the number of chars that would have been written, not
the actual number of chars written. This can lead to crashlog_buf->len
being too big which in turn can lead to get_maxlen() returning negative
numbers. The length argument of kmsg_dump_get_buffer will be casted to
a size_t which makes a negative input a big positive number allowing
kmsg_dump_get_buffer to write out of bounds.
Fix this by using vscnprintf which returns the actually written number
of chars.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 37820
Hauke Mehrtens
Gabor Juhos
Felix Fietkau
Jonas Gorski
Luka Perkov
Florian Fainelli