Update libbsd to 0.8.7
Remove glibc dependency
Clean up InstallDev and install entries
Use /usr path for consistency
Cherry pick patches from upstream to fix musl compilation
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
- Specifications -
CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.
Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1
Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/
Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/
To boot from the SD card:
Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr
Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.
Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Backport board support from the upcoming v2018.09 release,
and add an additional patch to read the MAC address
from flash memory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Without UHCI a non-trivial number of machines will have no keyboard
without BIOS assistance.
Add XHCI as well in case there are chipsets which don't support legacy
interfaces, and support PCI OHCI controllers also.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Starting with version 2.1.8, a release tarball is available.
Simplifies the Makefile slightly.
Updated the project URL. HTTPS is broken. Issue has been reported upstream
Adjusted patches. CMake support is not present in the tarball. It's made
for Windows anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
In some places the output of commands, which include "cd" are used.
In case of CDPATH the new path is printed, which might not be expected.
Disable the variable to avoid these problem.
When CDPATH was set by the user to some value like "export CDPATH=."
the git checkout done by the build system did not work anymore, the
git cloning aborted with such an error message for example:
....
Packing checkout...
tar: /disk/fs1/tmp2/mehrtens/pon-ugw/ugw-haps/openwrt/tmp/dl/ppa-drv-1.0\n@1534240258: Cannot stat: No such file or directory
tar: Date sample file not found
Try 'tar --help' or 'tar --usage' for more information.
.....
To avoid this, this patch makes the build system unset CDPATH inside
the build system, so the build system will still work even when the
user set this variable in his local environment.
Signed-off-by: Thomas Langer <thomas.langer@intel.com>
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
7daf962 mt7603: add survey support
980c606 mt7603: add fix for CCA signal configuration
30b8371 mt7603: fix BAR rate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CVE description :
The recv_msg_userauth_request function in svr-auth.c in Dropbear through
2018.76 is prone to a user enumeration vulnerability because username
validity affects how fields in SSH_MSG_USERAUTH messages are handled,
a similar issue to CVE-2018-15473 in an unrelated codebase.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch improves faf64056dd by correcting
the partition scheme for the "RouterBoot" section of the flash.
The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.
The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.
Leave a note in DTS to explain how the original author selected the SPI speed.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
This patch improves 5684d08741 by correcting
the partition scheme for the "RouterBoot" section of the flash.
The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.
The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.
The OEM source code also define a "RouterBootFake" partition at the
beginning of the secondary flash chip: to avoid trouble if OEM ever makes
use of that space, it is also defined here.
The resulting partition scheme looks like this:
[ 10.114241] m25p80 spi0.0: w25x40 (512 Kbytes)
[ 10.118708] 1 fixed-partitions partitions found on MTD device spi0.0
[ 10.125049] Creating 1 MTD partitions on "spi0.0":
[ 10.129824] 0x000000000000-0x000000040000 : "RouterBoot"
[ 10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot
[ 10.142894] Creating 5 MTD partitions on "RouterBoot":
[ 10.148032] 0x000000000000-0x00000000f000 : "bootloader1"
[ 10.154336] 0x00000000f000-0x000000010000 : "hard_config"
[ 10.160665] 0x000000010000-0x00000001f000 : "bootloader2"
[ 10.167046] 0x000000020000-0x000000021000 : "soft_config"
[ 10.173461] 0x000000030000-0x000000031000 : "bios"
[ 10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes)
[ 10.194950] 2 fixed-partitions partitions found on MTD device spi0.1
[ 10.201271] Creating 2 MTD partitions on "spi0.1":
[ 10.206071] 0x000000000000-0x000000040000 : "RouterBootFake"
[ 10.212746] 0x000000040000-0x000001000000 : "firmware"
[ 10.307216] 2 minor-fw partitions found on MTD device firmware
[ 10.313044] 0x000000040000-0x000000220000 : "kernel"
[ 10.319002] 0x000000220000-0x000001000000 : "rootfs"
[ 10.324906] mtd: device 9 (rootfs) set to be root filesystem
[ 10.330678] 1 squashfs-split partitions found on MTD device rootfs
[ 10.336886] 0x000000b40000-0x000001000000 : "rootfs_data"
Leave a note in DTS to explain how the original author selected the SPI speed.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
[rmilecki: dropped "RouterBootFake" partition]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI
mapping for them, so visual feedback on RSSI is available, when using
userspace RSSI monitor daemon.
Runtime tested using rssileds.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Create aliases for led-booting and led-failsafe pointing at
ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback
on device status becomes available, in order to enter failsafe mode
via button. led-running and led-upgrade aliases are omitted to avoid
conflicting with RSSI LEDs when in normal operation.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet
port, therefore disable creation of WAN zone and interfaces for them,
as their intended purpose is a wireless bridge. This aligns the
configuration with one found in ar71xx target.
ubnt,nano-m target is kept as is, being a two-port device.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards.
This is required for wireless interface to function.
Runtime tested on Nanobridge M5.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
I-O DATA ETG3-R is a wired router, based on Atheros AR9342.
Specification:
- Atheros AR9342
- 64 MB of RAM
- 8 MB of Flash
- 5x 10/100/1000 Ethernet
- AR8327N
- 2x LEDs, 1x key
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using initramfs image:
1. Connect serial cable to UART header on ETG3-R
2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in
the TFTP directory
3. Set IP address of the computer to 192.168.0.10, connect to the
LAN port of ETG3-R, and start the TFTP server on the computer
4. Connect power cable to ETG3-R and turn on the router
5. Press "Enter" key when the "Hit any key to stop autoboot:" message
is displayed on the console and enter the u-boot cli
6. execute following commands to change kernel address for u-boot
setenv bootsf 1
setenv mtd_kernel1 "bootm 0x9f050000"
saveenv
7. execute "tftpboot; bootm" command to download the initramfs image from
TFTP server and boot with it
8. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for ETG3-R
9. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The device was not included in the /etc/board.d/02_network file, so
the network wouldn't be properly set up on boot.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A.
This is almost same as WRC-2533GST except wireless specs.
Specifications:
- SoC : MT7621A (four logical CPU cores)
- RAM : 128MiB
- ROM : 16MiB of SPI NOR-FLASH
- wireless :
5GHz : 3T3R up to 1300Mbps/11ac with MT7615
2.4GHz : 3T3R up to 600Mbps/11n with MT7615
- Ethernet : 5 ports, all ports is capable of 1000base-T
- Ether switch : MT7530 (MT7621A built-in)
- LEDs : 4 LEDs
- buttons : 2 buttons and 1 slide-switch
- UART : header is on PCB, 57600bps
Flash instruction using factory image:
1. Connect the computer to the LAN port of WRC-1900GST
2. Connect power cable to WRC-1900GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't
have a jtag group. Having these groups defined might cause a boot
panic.
The pin controller fails to initialise for kernels > 4.9 if invalid
groups are used. If a subsystem references a pin controller
configuration node, it can not find this node and errors out. In worst
case it's the SPI driver which errors out and we have no root
filesystem to mount.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AX_AM_JOBSERVER macro shipped with m4/ax_am_jobserver.m4 is broken on
plain POSIX shells due to the use of `let`.
Shells lacking `let` will fail to run the generated m4sh code and end up
invoking "make" with "-jyes" as argument, fialing the build.
Since there is no reason in the first place for some random package to
muck with the make job server settings and since we do not want it to
randomly override "-j" either, simply remove references to this defunct
macro to let the build succeed on platforms which not happen to use bash
as default shell.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Patch 300-CVE-2015-8370.patch was added without proper rebasing on the
version used by OpenWrt, make it apply and refresh the patch to fix
compilation.
Fixes: 7e73e9128f ("grub2: Fix CVE-2015-8370")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest git HEAD in order to support configuring multiple
concurrent Lua prefixes in a single uhttpd instance:
b741dec lua: support multiple Lua prefixes
Additionally rework the init script and update the default configuration
example to treat the lua_prefix option as key=value uci list, similar to
the interpreter extension mapping. Support for the old "option lua_prefix"
plus "option lua_handler" notation is still present.
Finally drop the sed postinstall hack in uhttpd-mod-lua to avoid mangling
files belonging to other packages. Since Lua prefixes have precedence
over CGI prefixes, simply register `/cgi-bin/luci` as Lua handler which
will only become active if both luci-base and uhttpd-mod-lua is installed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This CVE is a culmination of multiple integer overflow issues that cause
multiple issues like Denial of Service and authentication bypass.
More info: https://nvd.nist.gov/vuln/detail/CVE-2015-8370
Taken from Fedora.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
While "rawnand.h" is available in kernel 4.14,
the default for this target is kernel 4.9 in which "nand.h" should be used.
Add an extra check to include the correct file depending on kernel version
Fixes these build errors:
drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory
#include <linux/mtd/rawnand.h>
^~~~~~~~~~~~~~~~~~~~~
compilation terminated.
Fixes: 318e19ba67 ("ar71xx: add v4.14 support")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Allows discovery without having to use NetBIOS. Useful for mobile devices.
Could eventually throw nbmd away. But that requires Windows 10...
Tested on Fedora 28 with avahi-discover.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Since kernel 4.14 there is no auto assignment of conntrack helpers anymore
so fw3 needs raw table support in order to stage ct helper assignment rules.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Remove creation of file /etc/ethers in dnsmasq init script as the
file is now created by default in the base-files package by
commit fa3301a28e
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
/etc/ethers is missing on /rom but always created when dnsmasq
runs. It is better to have it in place and avoid an extra change
in flash after firstboot.
It will generate an extra /etc/ethers-opkg when it has changed.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Engberg
Vladimir Vid
Antonio Silverio
Martin Schiller
Luis Araneda
Alex Maclean
Rosen Penev
Thomas Langer
Felix Fietkau
Hans Dedecker
Thibaut VARÈNE
Koen Vandeputte
Lech Perczak
INAGAKI Hiroshi
Roger Pueyo Centelles
NOGUCHI Hiroshi
Mathias Kresin
Jo-Philipp Wich
John Crispin
Luiz Angelo Daros de Luca