With the default network config provided by package base-files present,
board_detect won't create a new config from board.json.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 48076
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This fixes regression introduced in my recent ledtrig-netdev commit.
Events triggered by different interfaces were stopping timer so it
wasn't working for tx/rx mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48072
It was never tested, most likely not working (because of le32_to_cpu)
and not upstreamed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48060
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2
"MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is
defined in the .dts of vrx200 (VR9) SoCs.
SVN-Revision: 48056
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 48055
The ppp0 interface is renamed after the connection is established. Due
to a missing NETDEV_REGISTER event, the ledtrig-netdev isn't aware of
the renamed interface and literally ignores the device
(no tx/rx indication, led isn't switched off with 'ifdown wan').
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48048
The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those
leds.
Reported-by: Sylwester Petela <sscapi@gmail.com>
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48043
The leds of the following boards are not renamed due to lack of
manuals/informations:
- ARV7519PW
- ARV7510PW22
- ARV4510PW
The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48042
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.
The existing led sequences should be the same as before.
Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48041
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.
On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.
Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48040
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.
Rename the the wifi leds to make sure, the not applicable default
values get overwritten.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48038
- ARV7525PW: use the power led as dsl led as done by the stock firmware
- FRITZ3370: use the info led as internet led
- FRITZ7320: use the power led as dsl led as done by the stock firmware
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48037
Use the same led logic and labels as the OEM firmware (red = okay,
blue = failure).
Add the red internet led.
Remove missing usb led workaround. The workaround shouldn't be in the
default configuration.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48036
No need to switch (and keep) on all leds at boot. Use the same led
logic and labels as the OEM firmware (red = okay, blue = failure).
Add the red internet led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48035
Change the name of the .ubi produced to strip out the word 'factory'. This is
mainly due to the fact that there is no difference between the Ventana 'factory'
image vs the standard image.
Name changes from:
openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to
openwrt-imx6-ventana-squashfs-nand_<size>.ubi
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48016
Some Ventana boards have a Marvell sky2 GigE controller as eth1 however
assigning the mac address through device-tree is difficult because the
PCI slot can move around depending on board configuration and slot population.
To work around this we add a patch to the sky2 driver to allow accessing its
mac address via a device-tree alias.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48013
Rafał Miłecki
Felix Fietkau
John Crispin
Imre Kaloz
Luka Perkov