Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.
Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of grepping for NETWORK after calling ipcalc.sh; pass ipcalc.sh as
argument to eval allowing to use $NETWORK to retrieve the IPv4 prefix
(ip4prefix).
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.
Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.
Specification:
- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers
Flash instruction (do it under U-Boot, using UART and TFTP server):
Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Several new DRM symbols that were introduced after 4.9 are missing in
the generic config for 4.14, so add them.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Prevent emitting broken dependency statements when resolving references
to non existing packages to an empty provider list.
Fixes: 47d6b05ad3 ("metadata: always resolve dependencies through provides list")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The logic for choice between source and binary packages was reversed.
Fixes: 52719c2b67 "metadata: scripts/feeds: distinguish between source
and binary packages, resolve virtual dependencies"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Eventually the BUILDONLY package flag could be replaced by simply creating
a package Makefile without any BuildPackage calls. This will fail for now,
as BuildPackage also causes the Makefile's compile target etc. to do
something useful at all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Package "features" seem to be unused for some time. In any case, custom
Config.in snippets and package PROVIDES are a much more flexible way to
express similar options.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Properly resolve build depends to source packages and runtime depends to
binary packages. Dependencies on virtual packages are resolved to the first
provider now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Instead of adding virtual packages to the normal package list, keep a
separate list for provides, make each package provide itself, and resolve
all dependencies through this list. This allows to use PROVIDES to replace
existing packages.
Fixes FS#837.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Runtime depends cannot have a buildtype suffix, and they never refer to
source package names. In addition, this adds warnings about unsatisfiable
dependencies.
Furthermore, this change fixes the generation of conditional build
dependencies for virtual packages provided by different source packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Target build depends are similar to host build depends in that they refer
to source packages rather than binary packages. Therefore, it makes sense
to handle them together, rather than putting them in a list together with
runtime depends and trying to figure out if the entries refer to source or
to binary packages afterwards.
This does lead to PKG_BUILD_DEPENDS entries referring to binary package
names not working anymore, which requires some fixes in the package
repositories.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This feature has been unused for years, and its scope is too limited to be
actually useful.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Every single reference to subdir was concatenated with the source package
name, so it makes sense to store the concatenated value instead.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We often want to access fields of a source packages through pkg->{src}.
Allow accessing them directly instead of resolving the source hash through
srcpackages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All build dependencies are between source packages. Interating over source
rather than binary packages simplifies parts of the code and prepares
further improvement.
As a side effect, this changes the implicit default variant of a few
packages (the first defined is used now instead of the lexicographically
first).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Build types are a property of source rather than binary packages. This is a
preparation for followup cleanup.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Turn the srcpackage values into hashes to allow storing more information
than just binary package names.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Nothing explicitly depends on base-files, and even if it would, it would
not cause any problems. Remove the unused special case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
18090d9 overlay: fix compilation with glibc
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the
bootloader.
By default, all symbols containing INITRAMFS are wiped from the final
config and then re-added conditionally.
Add support for this symbol, as the build will stop otherwise
questioning the user about this option:
* Restart config...
*
*
* General setup
*
Cross-compiler tool prefix (CROSS_COMPILE) []
Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n
...
Initial RAM filesystem and RAM disk (initramfs/initrd) support
(BLK_DEV_INITRD) [Y/n/?] y
Initramfs source file(s) (INITRAMFS_SOURCE) []
Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE)
[N/y/?] (NEW)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.
This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich
Hans Dedecker
Roger Pueyo Centelles
Piotr Dymacz
Davide Fioravanti
Stijn Tintel
Matthias Schiffer
John Crispin
Koen Vandeputte