NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position) and an E3372 device (which mandates NDP
to be after indexed datagrams).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46464
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
There are a few NETGEAR devices which don't terminate the model name in the
ART with a NUL byte, at least some NETGEAR WNDR3700v2. The current awk
expression doesn't match 0xFF bytes, so AR71XX_MODEL contains lots of
trailing 0xFF garbage in this case.
Fix this by matching for the first non-printable character and explicitly
setting LC_CTYPE=C (probably not strictly necessary on OpenWrt, but will
definitely work like this, even when awk supports locales and LANG is set).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46455
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This ports 9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46453
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Now that we have a dtc command that invokes the preprocessor, make use
of it and replace the magic numbers with KEY_* defines.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46391
Felix Fietkau
John Crispin
Jonas Gorski