Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45599
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43074
The default inittab uses "askconsole" which is implemented by procd
and uses the console provided by the kernel command line.
Hence, this platform specific workaround is not necessary anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39367
Felix Fietkau
Jo-Philipp Wich
Imre Kaloz
Luka Perkov
John Crispin
Gabor Juhos