PTP requires at least one timer to be 1PPS so describe it.
For testing, load kernel module gianfar_ptp and use ptp4l
from linuxptp.
Copied from FSL P1010RDB reference design.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 48275
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if
the selected subtarget is 'generic'.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47109
This patch adds the RFKill GPIO control switch and enables another GPIO to
control power supply to USB Ports by emulating an LED GPIO for WDR4900v1.
Signed-off-by: Guo Wei Lim <alphasparc@gmail.com>
SVN-Revision: 46279
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.
This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45749
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45599
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
It took very little to make the TL-WDR4900 work under 3.19:
- config is the same as for 3.18
- only patch 210 had to be refreshed, the other patches are
the same as for 3.18
- in /etc/config/wireless the path options need to be prefixed
with "platform/" ('platform/ffe09000.pci/...')
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44517
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@ffe00000/timer@41100: cannot get timer frequency.
/soc@ffe00000/timer@42100: cannot get timer frequency.
This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
"clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44501
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa.
To maintain compatibility define p1010rdb-pa as new standard and
copy p1010rdb.dts to p1010rdb-pa.dts under 3.10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43371
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43308
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43074
John Crispin
Felix Fietkau
Jo-Philipp Wich
Jonas Gorski
Imre Kaloz
Luka Perkov