Looks like the addresses for BCM3368 were wrongly defined when DT
support was introduced.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48980
This patch adds support for the NuCom R5010UNv2.
It's a BCM6328 based board. It has an onboard BCM43217 wifi chip. For this
wifi chip looks like the brcmsmac driver isn't still supported, b43 drivers are used
for the profile of the router.
It's worth mentioning this board was affected by a bug solved with
https://dev.openwrt.org/changeset/46707
Tested-by: Angel Fontan <angel.fontan@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47697
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.
Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46752
BCM6318: add support for Plusnet / Sagem 2704N (V1)
Signed-off-by: Matt Goring <matt.goring@googlemail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46562
Now that we have a dtc command that invokes the preprocessor, make use
of it and replace the magic numbers with KEY_* defines.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46391
This patch adds buttons support for Huawei EchoLife HG553.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46388
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45583
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44566
Add a generic mmio gpio controller based driver and probe it
through device tree.
Use aliases for base calculation until we converted all users to
device tree or named gpios.
Convert bcm63xx_enet's ephy-reset gpio to use a named gpio.
While at it, remove the duplicate reset gpio defintion for livebox.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44565
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert
it to use ImageDTB. Since HCS requires more arguments, enhance the max
arguments of the call.
The image name is intentionally left blank to prevent non-initramfs
images to be built, as they currently contain no rootfs and consequently
won't work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44561
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
Add the required nodes for the interrupt controllers and register
them through DT when a DTB is present.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43457
John Crispin
Jonas Gorski