This patch tries to
- Let the DHCPv6 feature depend on CONFIG_IPV6.
- Conditionally select libnettle, kmod-ipv6, kmod-ipt-ipset only if the
corresponding features are enabled.
- Install `trust-anchors.conf` only if DNSSEC is selected.
- Add PKG_CONFIG_DEPENDS for the configurable options.
- Add a patch to let the Makefile of dnsmasq be aware of changes in
COPTS variable.
Big thanks goes to Frank Schäfer <fschaefer.oss@googlemail.com> for
providing necessary information on connections and dependency relations
between these CONFIGs and packages.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43851
Target pxcab and ps3 were removed from maintaince in r34764 and r34765
respectively.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43850
The uapsd option sets the uapsd_advertisement_enabled flag in hostapd.
The check for phy support is already implemented here in hostapd since 2011:
http://w1.fi/cgit/hostap/commit/?id=70619a5d8a3d32faa43d66bcb1b670cacf0c243e
So this can be safely set to 1 as default.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43846
Commit ce92f6650bd8a86db04c7a6cbb58e7fdb200a7e6 added source IP support
for DHCP default routes. As a side effect of this change the default route
could be present twice in netifd (once with source IP set and once with
source IP unset) if it was sent by the server in both the router and static
route options. Therefore add source IP support as well for static routes as this
case was not considered. Additional remove unused parameter type.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 43645
I have not found a scenario that would break by setting the source address on
default, but please let me know if any special considerations should be taken.
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
SVN-Revision: 43582
Added complementary blobmsg_close_table() before returning from function
on error.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 43477
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
Thanks to Dave Taht for debugging and thanks to Comcast for
shipping strangely behaving software so I can fix some corner cases.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 43415
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
b52053b 6in4: https support for he.net tunnel api
introduced HTTPS support using wget.
The busybox version of wget, however, doesn't support the -V option,
thus poluting logfiles with a full invalid-parameter-output.
Redirect stderr to fix that.
As libcurl and curl support selecting the SSL library of your choice,
also add support for curl which is more commonly used on OpenWrt than
"real" wget which needs libopenssl.
Also make sure to respect SSL_CERT_DIR and increase timeouts.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43228
This patch adds the userspace and kernelspace for
- match NETFILTER_XT_MATCH_CLUSTER
This match can be used to deploy gateway and back-end load-sharing clusters.
- target IP_NF_TARGET_CLUSTERIP
This module allows you to configure a simple cluster of nodes
that share a certain IP and MAC address
without an explicit load balancer in front of them.
Connections are statically distributed between the nodes in this cluster.
This is used i.e. by strongswan-ha.
Signed-off-by: Christian Scheele <cs@embedd.com>
SVN-Revision: 43174
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Port Debians adaptive LCP echo patch to pppd, make it configurable with UCI
and enable it by default.
When adaptive LCP echo is enabled, LCP echo requests are only sent if the
link is idle, this avoids the common situation where a congested PPP link
(e.g. during torrenting) is falsely detected as disconnected because the
LCP replies are not received in time.
Also bump the copyright year in the Makefile, remove a redundant maintainer
entry and fix the shell processing of the keepalive option when the two-
value syntax is used.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43143
HE.net tunnel update API requests are now made via https if an
SSL-capable wget is installed. Certificate validation is
conditionally enabled if the CA certs are available.
Signed-off-by: Andrew Skalski <askalski@gmail.com>
SVN-Revision: 43124
I had to use a VDSL-only tone-setup to get show-time.
Handle this in uci by checking if annex is unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43114
* Fixes sending an extraneous message body for 204 and 304 resoponses which
breaks Chrome in keep-alive mode.
* Adds mimetypes for JSON and JSONP.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43078
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
* Rewrite ndp proxy using kernel proxying
* Aid flash-renumbering in hybrid DHCPv6-mode
* Unicast RAs to RS senders
* Add support for router address
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42944
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
Patch allows to configure the mtu of the dynamic 6rd tunnel interface when created by dhcp script.
In some setups it's desirable to have config control over the 6rd tunnel mtu to maximize the traffic throughput
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42871
This is not needed after all:
Omitting option ipv6 or setting it to 'auto' will
fire up a dhcpv6 subprotocol (this was added).
Setting ipv6 to 1 will only cause the IPv6 link to
be brought up and an accompanying dhcpv6 or static
interface with ifname @wan can be used to configure addresses.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42859
Use network_get_ipaddrs_all to get all ip-addresses of an interface. If the
function fails, the interface does not exists or has not any suiteable ip
addresses assigned.
Use the returned ip-address(es) to construct the dropbear listen address.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 42857
this proto handler will detect which of 3g, qmi, mbim, ncm or directip you need
for a stick and setup uci automagically
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42837
Some ISP seem to only do stateful DHCPv6 and not sending RAs.
This is technically broken because plain DHCPv6 doesn't carry routes.
We work around here by faking a default route to the DHCPv6 server
if we do not receive a useful RA from the ISP.
This workaround can be turned off with: option fakeroutes 0
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42803
The AR9580 with the new ID can be found in the EnGenius ESR900 and the
QCA9880 without any subsystem IDs can be found in the EnGenius ESR1750.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
SVN-Revision: 42793
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
Jo-Philipp Wich
Felix Fietkau
Imre Kaloz
Steven Barth
John Crispin
Matteo Croce
Nicolas Thill