Commit Graph

19 Commits (c864661d148cf3f9d955fc9a26a6d2c5808c0e29)

Author SHA1 Message Date
Christian Lamparter 1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Adrian Panella d700c120bf ipq806x: EA8500 fix sysupgrade over stock firmware
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-12-20 09:35:37 +01:00
Sebastian Quilitz ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Felix Fietkau b5ee86c4e5 ipq806x: remove device specific sysupgrade image checks
Replaced by image metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-20 20:08:39 +01:00
Felix Fietkau 9d6d7d9a0e ipq806x: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
André Valentin 1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Henryk Heisig 4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Alexis Green c34f953fef ipq806x: Build image for Netgear Nighthawk X4 R7500v2
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-08-22 17:24:48 +02:00
Pavel Kubelun 823242185b ipq806x: add initial support for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:06 +02:00
Adrian Panella 3d067c0132 ipq806x: base-files: add support for Linksys EA8500
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
Ash Benz 14515cc271 ipq806x/base-files: Add support for Archer C2600
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
John Crispin 78a6a9aec3 ipq806x: Add support for Netgear D7800
Signed-off-by: Tathagata Das <tathagata@alumnux.com>

SVN-Revision: 48360
2016-01-19 10:16:36 +00:00
Jonas Gorski 25ce154605 ipq806x: fix sysupgrade for AP148
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 48304
2016-01-18 10:46:58 +00:00
Rafał Miłecki ffcb268437 ipq806x: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

This follows ar71xx, lantiq and partially bcm53xx.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46945
2015-09-15 16:05:10 +00:00
Jonas Gorski 8b4df1efd5 ipq806x: add support for Netgear Nighthawk X4 R7500
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.

Known issues:
 * 5 GHz wifi not working - there is no quantenna driver
 * One of the USB ports is not working

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46796
2015-09-04 14:46:06 +00:00
Jonas Gorski 89815d4645 ipq806x: build images and add sysupgrade support for AP148
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46789
2015-09-04 14:45:00 +00:00
John Crispin 0ddebefc74 ipq806x: add db149 support to OpenWrt init scripts
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45537
2015-04-21 07:15:47 +00:00
John Crispin 3c1f6e358d ipq806x: Add support for IPQ806x chip family
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.

All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.

Support is currently limited to AP148 board but can be extended to other
platforms in the future.

These changes do not cover ethernet connectivity.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 42334
2014-08-30 09:32:58 +00:00